Cylinder Head

In this manual: Cylinder Head
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~18min read
9special tools
010203040509.57N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Disassembly
  • Inspection
  • Reassembly
  • Repair

Precaution

PRECAUTION

HINT:

  • Any digits beyond the 0.01 mm (1/1000 in.) place for standard, minimum and maximum values should be used as a reference only.
  • When both standard and maximum or minimum values are listed for an inspection, use the standard value as a reference only and base any judgments on the maximum and minimum values.

Disassembly

DISASSEMBLY

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

Replacement of ECM

Update ECU security key

Toyota Prius Vehicle Control History (RoB) are stored

ECU configuration

-

Perform Toyota Prius Vehicle Identification Number (VIN) registration

DTC is output

  • Replacement of throttle body assembly
  • Replacement of cylinder head sub-assembly
  • Replacement of camshaft (for intake or exhaust camshaft)
  • Replacement of camshaft timing gear assembly
  • Replacement of fuel injector assembly
  • Replacement of spark plug
  • Replacement of ignition coil assembly
  • Replacement of EGR valve assembly
  • Gas leak from exhaust system is repaired
  • Replacement of knock control sensor

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

Replacement of inverter with converter assembly

ECU configuration

-

Resolver learning

  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Replacement of hybrid vehicle transaxle assembly

  • Resolver learning
  • Initialize resolver
  • DTCs are stored
  • Slight vibration at a Toyota Prius vehicle speed of 5 km/h or less
  • Shock or vibration during acceleration

Suspension parts

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Tires

  • Initialization*1*2
  • Tire Position Identification*1*2

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) table below

Rear television camera assembly optical axis (Back camera position setting)

Parking Assist Monitor System

Parking assist ECU initialization

Panoramic View Monitor System

Advanced Park

Replacement of front bumper assembly*

Front television camera view adjustment

Panoramic View Monitor System

Advanced Park

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  • Learning completes when Toyota Prius vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    Front Camera System

    Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

  • Learning completes when vehicle is operated normally

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    *1: w/o Power Back Door System

    *2: w/ Power Back Door System

    Power Door Lock Control System*1

    • Back door opener

    Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

    Power Back Door System*2

    Reset back door close position

    Air Conditioning System

    After the ignition switch is turned to ON, the servo motor standard position is recognized.

    -

COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

VALVE SPRING RETAINER ROCK

-

-

-

2

VALVE SPRING RETAINER

-

-

-

-

3

INTAKE VALVE COMPRESSION SPRING

-

-

-

-

4

EXHAUST VALVE COMPRESSION SPRING

-

-

-

-

5

INTAKE VALVE

13711

-

-

-

6

EXHAUST VALVE

13715

-

-

-

7

VALVE STEM OIL SEAL

-

-

-

8

VALVE SPRING SEAT

13734

-

-

9

NO. 1 STRAIGHT SCREW PLUG

11117E

-

-

10

INTAKE VALVE GUIDE BUSH

11122

-

-

11

EXHAUST VALVE GUIDE BUSH

11126

-

-

12

RING PIN

-

-

-

-

13

STUD BOLT

-

-

-

-

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE VALVE SPRING RETAINER ROCK

(1) Using SST and wooden blocks, compress the inner compression spring and remove the 16 valve spring retainer locks.

SST: 09202-70020

09202-01010

09202-01020

SST: 09202-00021

2. REMOVE VALVE SPRING RETAINER

3. REMOVE INTAKE VALVE COMPRESSION SPRING

4. REMOVE EXHAUST VALVE COMPRESSION SPRING

(a) Perform the same procedure as for the intake side.

5. REMOVE INTAKE VALVE

6. REMOVE EXHAUST VALVE

(a) Perform the same procedure as for the intake side.

7. REMOVE VALVE STEM OIL SEAL

(1) Using needle-nose pliers, remove the 16 valve stem oil seals.

8. REMOVE VALVE SPRING SEAT

(1) Using compressed air and a Magnet Hand, remove the 16 valve spring seats from the cylinder head sub-assembly by blowing air onto them.

9. REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.

(1) Using a 10 mm straight hexagon wrench, remove the 3 No. 1 straight screw plugs and 3 gaskets from the cylinder head sub-assembly.

10. REMOVE INTAKE VALVE GUIDE BUSH

(1) Heat the cylinder head sub-assembly to 80 to 100 °C.

(2) Using SST and a hammer, tap out the intake valve guide bush.

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

11. REMOVE EXHAUST VALVE GUIDE BUSH

(1) Heat the cylinder head sub-assembly to 80 to 100 °C.

(2) Using SST and a hammer, tap out the exhaust valve guide bush.

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

12. REMOVE RING PIN

13. REMOVE STUD BOLT

Inspection

INSPECTION

PROCEDURE

1. INSPECT CYLINDER HEAD SUB-ASSEMBLY FOR WARPAGE

(a) Using a precision straightedge and feeler gauge, check the surfaces which contact the cylinder head sub-assembly and manifold for warpage.

Maximum Warpage:

Item

Specified Condition

Result

Bottom side

0.05 mm

0.00197 in.

mm

in.

Intake manifold side

0.10 mm

0.00394 in.

mm

in.

Exhaust manifold side

0.10 mm

0.00394 in.

mm

in.

*a

Bottom Side

*b

Intake Manifold Side

*c

Exhaust Manifold Side

(b) If the warpage is more than the maximum, replace the cylinder head sub-assembly.

2. INSPECT CYLINDER HEAD SUB-ASSEMBLY FOR CRACKS

(a) Using a dye penetrant, check the intake ports, exhaust ports and bottom surface of the cylinder head sub-assembly for cracks.

(b) If cracks are found, replace the cylinder head sub-assembly.

3. INSPECT INTAKE VALVE

(a) Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:

Minimum Overall Length

Specified Condition

Result

108.84 mm

4.29 in.

109.34 mm

4.30 in.

mm

in.

(1) If the overall length is less than the minimum, replace the intake valve.

*a

Overall Length

(b) Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

Specified Condition

Result

5.470 to 5.485 mm

0.215 to 0.216 in.

mm

in.

(1) If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.

HINT:

Click here

(c) Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

Minimum Margin Thickness

Specified Condition

Result

0.5 mm

0.0197 in.

1.0 mm

0.0394 in.

mm

in.

(1) If the margin thickness is less than the minimum, replace the intake valve.

*a

Margin Thickness

4. INSPECT EXHAUST VALVE

(a) Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:

Minimum Overall Length

Specified Condition

Result

107.75 mm

4.24 in.

108.25 mm

4.26 in.

mm

in.

(1) If the overall length is less than the minimum, replace the exhaust valve.

*a

Overall Length

(b) Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

Specified Condition

Result

5.465 to 5.480 mm

0.215 to 0.216 in.

mm

in.

(1) If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.

HINT:

Click here

(c) Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

Minimum Margin Thickness

Specified Condition

Result

0.5 mm

0.0197 in.

1.0 mm

0.0394 in.

mm

in.

(1) If the margin thickness is less than the minimum, replace the exhaust valve.

*a

Margin Thickness

5. INSPECT INNER COMPRESSION SPRING

(a) Using a vernier caliper, measure the free length of the inner compression spring.

Standard Free Length:

Specified Condition

Result

58.52 mm

2.30 in.

mm

in.

Specified Condition

Result

58.90 mm

2.32 in.

mm

in.

NOTICE:

Inner compression springs come in 2 different lengths. Make sure all inner compression springs are the same length when replacing them.

(b) Using a steel square, measure the angle of the inner compression spring.

Maximum Angle (Reference):

2°

(1) If the deviation is greater than the maximum, replace the inner compression spring.

*a

Angle

*b

40 mm (1.57 in.)

6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE

(a) Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

Specified Condition

Result

5.510 to 5.530 mm

0.217 to 0.218 in.

mm

in.

(b) Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:

Item

Maximum Oil Clearance

Specified Condition

Result

Intake Side

0.080 mm

0.00315 in.

0.025 to 0.060 mm

0.000984 to 0.00236 in.

mm

in.

Exhaust Side

0.085 mm

0.00335 in.

0.030 to 0.065 mm

0.00118 to 0.00256 in.

mm

in.

HINT:

Oil clearance = Inside diameter - Valve stem diameter

(1) If the oil clearance is more than the maximum, replace the valve and valve guide bush.

7. INSPECT VALVE SEATS

Pre-procedure1

(a) Apply a light coat of Prussian blue to the valve face.

*a

Width

(b) Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing it.

Procedure1

(c) Check the valve face and valve seat.

(1) If Prussian blue appears 360° around the entire valve face, the valve face is concentric.

(2) If the valve face is not concentric, replace the valve.

(3) If Prussian blue appears 360° around the entire valve seat, the valve seat and valve face are concentric.

(4) If the valve face is not concentric, resurface the valve seat.

HINT:

Click here

(5) Measure the width of the contact area of the valve seat and valve face.

Standard Width:

Item

Specified Condition

Result

Intake Side

1.0 to 1.4 mm

0.0394 to 0.0551 in.

mm

in.

Exhaust Side

1.0 to 1.4 mm

0.0394 to 0.0551 in.

mm

in.

Post-procedure1

(d) None

Reassembly

REASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click here

COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

SPARK PLUG TUBE

-

-

-

2

RING PIN

-

-

-

3

STUD BOLT

-

-

-

4

INTAKE VALVE GUIDE BUSH

11122

-

-

5

EXHAUST VALVE GUIDE BUSH

11126

-

-

6

NO. 1 STRAIGHT SCREW PLUG

11117E

-

-

7

VALVE SPRING SEAT

13734

-

-

-

8

VALVE STEM OIL SEAL

-

-

-

9

INTAKE VALVE

13711

-

-

10

EXHAUST VALVE

13715

-

-

11

INTAKE VALVE COMPRESSION SPRING

-

-

-

12

EXHAUST VALVE COMPRESSION SPRING

-

-

-

13

VALVE SPRING RETAINER

-

-

-

-

14

VALVE SPRING RETAINER ROCK

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Adhesive 1324

★

Precoated part

PROCEDURE

1. INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head sub-assembly, the spark plug tube must be replaced.

*a

Application Width

*b

1.0 to 13.0 mm (0.0394 to 0.512 in.)

*c

Protrusion Height

-

-

(1) Apply adhesive to the area of a new spark plug tube shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)

NOTICE:

  • Install the spark plug tube within 3 minutes of applying adhesive.
  • Be careful not to deform the spark plug tube.
  • Be careful not to expose the adhesive to engine oil for at least 1 hour after installing the spark plug tube.

(2) Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard Protrusion Height:

122 mm (4.80 in.)

NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

2. INSTALL RING PIN

(1) Using a plastic hammer, tap in 2 new ring pins to the specified protrusion height.

Standard Ring Pin:

Item

Height

Width

Protrusion Height

Ring pin

11.7 to 12.3 mm (0.461 to 0.484 in.)

12.0 mm (0.472 in.)

6.5 to 7.5 mm (0.256 to 0.295 in.)

3. INSTALL STUD BOLT

*a

Intake Manifold Side

*b

Exhaust Manifold Side

*c

Cylinder Head Rear Side

*d

55 mm (2.17 in.)

*e

13 mm (0.512 in.)

*f

26 mm (1.02 in.)

*g

24 mm (0.945 in.)

*h

49.5 mm (1.95 in.)

*i

20 mm (0.787 in.)

*j

42 mm (1.65 in.)

(1) Using E7 and E8 "TORX" socket wrenches, install the 9 stud bolts to the cylinder head sub-assembly.

Torque:

9,5 N·m {97 kgf·cm, 84 in·lbf}

4. INSTALL INTAKE VALVE GUIDE BUSH

*a

Height

-

-

(1) Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

New Guide Bush Selection Chart (STD or O/S 0.05):

Bush Size

Bush Diameter

STD

10.333 to 10.344 mm (0.4068 to 0.4072 in.)

O/S 0.05

10.383 to 10.394 mm (0.4088 to 0.4092 in.)

HINT:

  • If the intake valve guide bush bore diameter is more than 10.306 mm (0.40575 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.40689 to 0.40772 in.) to install an O/S 0.05 intake valve guide bush.
  • If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.40772 in.), replace the cylinder head sub-assembly.

(2) Heat the cylinder head sub-assembly to 80 to 100 °C.

(3) Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

Standard Protrusion Height:

9.9 to 10.3 mm (0.390 to 0.406 in.)

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

(4) Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance between the intake valve guide bush and valve stem.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.002362 in.)

5. INSTALL EXHAUST VALVE GUIDE BUSH

*a

Height

-

-

(1) Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

New Guide Bush Selection Chart (STD or O/S 0.05):

Bush Size

Bush Diameter

STD

10.333 to 10.344 mm (0.4068 to 0.4072 in.)

O/S 0.05

10.383 to 10.394 mm (0.4088 to 0.4092 in.)

HINT:

  • If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.40575 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.40689 to 0.40772 in.) to install an O/S 0.05 exhaust valve guide bush.
  • If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.40772 in.), replace the cylinder head sub-assembly.

(2) Heat the cylinder head sub-assembly to 80 to 100 °C.

(3) Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

Standard Protrusion Height:

11.15 to 11.55 mm (0.439 to 0.455 in.)

(4) Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance between the exhaust valve guide bush and valve stem.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)

6. INSTALL NO. 1 STRAIGHT SCREW PLUG

HINT:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.

(1) Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs to the cylinder head sub-assembly.

Torque:

44 N·m {449 kgf·cm, 32 ft·lbf}

7. INSTALL VALVE SPRING SEAT

8. INSTALL VALVE STEM OIL SEAL

*a

Intake side

*b

Exhaust side

*c

Gray

*d

Black

*e

Correct

*f

Incorrect

(1) Apply a light coat of engine oil to 16 new valve stem oil seals.

NOTICE:

Pay attention when installing the valve stem oil seals. For example, installing an intake side valve stem oil seal to the exhaust side or installing an exhaust side valve stem oil seal to the intake side can cause installation problems later.

HINT:

The intake valve stem oil seal is gray and the exhaust valve stem oil seal is black.

(2) Using SST, push in the 16 valve stem oil seals.

SST: 09201-41020

NOTICE:

  • Failure to use SST will cause the valve stem oil seal to be damaged or improperly seated.
  • Do not push in the valve stem oil seals at an angle.

9. INSTALL INTAKE VALVE

*a

30 mm (1.18 in.) or more

-

-

(1) Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.

(2) Install the 8 intake valves to the cylinder head sub-assembly.

10. INSTALL EXHAUST VALVE

(a) Perform the same procedure as for the intake side.

11. INSTALL INTAKE VALVE COMPRESSION SPRING

NOTICE:

  • Install the inner compression spring with its tapered side facing upward (towards the valve spring retainer).
  • Install the same parts in the same combination to their original locations.

12. INSTALL EXHAUST VALVE COMPRESSION SPRING

NOTICE:

  • Install the inner compression spring with its tapered side facing upward (towards the valve spring retainer).
  • Install the same parts in the same combination to their original locations.

13. INSTALL VALVE SPRING RETAINER

14. INSTALL VALVE SPRING RETAINER ROCK

(1) Using SST and wooden blocks, compress the inner compression spring and install the 16 valve spring retainer locks.

SST: 09202-70020

09202-01010

09202-01020

SST: 09202-00021

(2) Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

  • Be careful not to damage the valve stem tip.
  • Be careful not to damage the valve spring retainer.

Repair

REPAIR

PROCEDURE

1. REPAIR VALVE SEAT

NOTICE:

  • Repair the valve seat while checking the seating position.
  • Release the cutter gradually to make the valve seat smooth.

(a) Using a 45° cutter, resurface the valve seat so that the valve seat width is more than the standard.

(b) Using 30° and 75° cutters, resurface the valve seat so that the valve contacts the entire circumference of the valve seat. The contact should be in the center of the valve seat, and the valve seat width should be maintained within the specified range around the entire circumference of the valve seat.

Standard Valve Seat Width:

1.0 to 1.4 mm (0.0394 to 0.0551 in.)

*a

Valve Seat Width

(c) Hand lap the valve and valve seat with an abrasive compound.

(d) Check the valve seating position.