Lin Communication System

In this manual: Lin Communication System
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~43min read
  • Precaution
  • Parts Location
  • System Description
  • How To Proceed With Troubleshooting
  • Terminals Of Ecu
  • Data List / Active Test
  • Diagnostic Trouble Code Chart
  • P/W Master SW System Missing Message (B120687,B232187-B232487)
  • LIN Communication Missing Message (B228787)
  • Door LIN Bus off (B232588)
  • Alarm / Wiper LIN Bus off (B276C88)
  • Communication between ECUs connected by LIN Bus off (B278588)
  • ID-BOX Missing Message (B278987)
  • Power Source Control System Missing Message (B278C87)

Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*A

w/ Auto Wiper System

-

-

*1

POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR)

*2

POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR)

*3

POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR)

*4

POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR)

*5

RAIN SENSOR

-

-

ILLUSTRATION

*1

MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

*2

CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*3

ID CODE BOX (IMMOBILISER CODE ECU)

*4

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*5

DLC3

*6

POWER DISTRIBUTION BOX ASSEMBLY

- ECU-B NO. 1 FUSE

- ECU-B NO. 2 FUSE

- DOOR F/L FUSE

- DOOR F/R FUSE

- DOOR R/L FUSE

- DOOR R/R FUSE

System Description

SYSTEM DESCRIPTION

LIN COMMUNICATION SYSTEM DESCRIPTION

The LIN communication system is used for communication between the components in the tables below. If communication cannot be performed through LIN communication such as when there is an open or short in a communication line, the master control ECU of the relevant system will store a DTC. Refer to the table below about the communication bus lines and connected components.

HINT:

  • Each component has a fail-safe function which operates in the event of a malfunction to protect the system and allow communication between other components to continue.
  • In the following table, "○" indicates that the function applies, and "-" indicates that it does not.
Door Bus Lines

Component

Master Control

LIN Communication DTC Output Function

Main Body ECU (Multiplex Network Body ECU)

○

○

Power Window Regulator Motor Assembly LH (Driver Door)

-

-

Power Window Regulator Motor Assembly RH (Front Passenger Door)

-

-

Power Window Regulator Motor Assembly LH (Rear LH Door)

-

-

Power Window Regulator Motor Assembly RH (Rear RH Door)

-

-

Multiplex Network Master Switch Assembly

-

-

Certification Bus Lines

Component

Master Control

LIN Communication DTC Output Function

Certification ECU (Smart Key ECU Assembly)

○

○

ID Code Box (Immobiliser Code ECU)

-

-

Sensor Bus Lines (w/ Auto Wiper System)

Component

Master Control

LIN Communication DTC Output Function

Main Body ECU (Multiplex Network Body ECU)

○

○

Rain Sensor

-

-

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the LIN communication system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
  • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
  • The following 5 items are important points for problem analysis:

What

Toyota Prius Vehicle model, system name

When

Date, time, occurrence frequency

Where

Road conditions

Under what conditions?

Driving conditions, weather conditions

How did it happen?

Problem symptoms

NEXT
  1. PRE-CHECK

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

for HEV Model: Click here

for PHEV Model: Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for PHEV Model: Click here

A
  1. INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Using the GTS, check for LIN communication system DTCs.

Body Electrical > Main Body > Trouble Codes Body Electrical > Power Source Control > Trouble Codes Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

LIN DTCs are not output

A

LIN DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Terminals of ECU

Click here

(b) Data List / Active Test

Click here

NEXT
  1. REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Terminals Of Ecu

TERMINALS OF ECU

CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Disconnect the z1 main body ECU (multiplex network body ECU) connector.

Click here

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

z1-13 (GND1) - Body ground

Ground

Always

Below 1 Ω

z1-14 (GND2) - Body ground

Ground

Always

Below 1 Ω

z1-26 (BECU) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

z1-27 (IGR) - Body ground

IG power supply

Ignition switch ON

11 to 14 V

Ignition switch off

Below 1 V

(c) Reconnect the z1 main body ECU (multiplex network body ECU) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

R17-17 - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) Disconnect the O8 multiplex network master switch assembly connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O8-1 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

O8-4 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the O8 multiplex network master switch assembly connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O8-3 (LIN1) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

O8-9 (LIN2) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR)

(a) Disconnect the O5 power window regulator motor assembly LH (driver door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O5-2 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

O5-1 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the O5 power window regulator motor assembly LH (driver door) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

O5-9 (LIN) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR)

(a) Disconnect the N4 power window regulator motor assembly RH (front passenger door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N4-2 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

N4-1 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the N4 power window regulator motor assembly RH (front passenger door) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

N4-9 (LIN) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR)

(a) Disconnect the M2 power window regulator motor assembly LH (rear LH door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M2-2 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

M2-1 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the M2 power window regulator motor assembly LH (rear LH door) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

M2-9 (LIN) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR)

(a) Disconnect the L2 power window regulator motor assembly RH (rear RH door) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L2-2 (B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

L2-1 (GND) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the L2 power window regulator motor assembly RH (rear RH door) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

L2-9 (LIN) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the K13 certification ECU (smart key ECU assembly) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K13-6 ( B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

K13-29 (E) - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the K13 certification ECU (smart key ECU assembly) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K13-8 (LIN) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK ID CODE BOX (IMMOBILISER CODE ECU)

(a) Disconnect the K43 ID code box (immobiliser code ECU) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K43-5 (GND) - Body ground

Ground

Always

Below 1 Ω

K43-1 ( B) - Body ground

B power supply

Ignition switch off

11 to 14 V

(c) Reconnect the K43 ID code box (immobiliser code ECU) connector.

(d) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

K43-2 (LIN1) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

CHECK RAIN SENSOR (w/ Auto Wiper System)

(a) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

U4-3 (MPX) - Body ground

LIN communication line

Ignition switch ON

Pulse generation

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Communication D-Door Motor

Connection status between power window regulator motor assembly LH (driver door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTC is output if an error occurs in LIN communication.

Communication P-Door Motor

Connection status between power window regulator motor assembly RH (front passenger door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTC is output if an error occurs in LIN communication.

Communication RR-Door Motor

Connection status between power window regulator motor assembly RH (rear RH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTC is output if an error occurs in LIN communication.

Communication RL-Door Motor

Connection status between power window regulator motor assembly LH (rear LH door) and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTC is output if an error occurs in LIN communication.

Communication Intrusion Sensor 1

Connection status between map light assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • Not applicable
  • Although the item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Intrusion Sensor 2

Connection status between map light assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • Not applicable
  • Although the item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Sunshade ECU

Connection status between roof sunshade ECU and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • Not applicable
  • Although the item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Slide Roof

Connection status between sliding roof ECU and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • Not applicable
  • Although the item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Humidity/Rain Sensor

Connection status between rain sensor and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • w/ Auto Wiper System
  • DTC is output if an error occurs in LIN communication.

Communication Double Locking

Connection status between double lock door control relay assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

  • Not applicable
  • Although the item is displayed on the GTS, it is not applicable to this Toyota Prius vehicle.

Communication Master Switch

Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU)

STOP or OK

STOP: Not Connected

OK: Connected

DTC is output if an error occurs in LIN communication.

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

LIN Communication System

DTC No.

Detection Item

DTC Output from

Priority

Link

B120687

P/W Master SW System Missing Message

Main Body

A

B228787

LIN Communication Missing Message

Power Source Control

B

B232187

D-Door P/W System Missing Message

Main Body

A

B232287

P-Door P/W System Missing Message

Main Body

A

B232387

RR-Door P/W System Missing Message

Main Body

A

B232487

RL-Door P/W System Missing Message

Main Body

A

B232588

Door LIN Bus off

Main Body

A

B276C88

Alarm / Wiper LIN Bus off

Main Body

A

B278588

Communication between ECUs connected by LIN Bus off

Smart Key

A

B278987

ID-BOX Missing Message

Smart Key

A

B278C87

Power Source Control System Missing Message

Smart Key

A

P/W Master SW System Missing Message (B120687,B232187-B232487)

DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, power window regulator motor assembly LH (driver door), power window regulator motor assembly RH (front passenger door), power window regulator motor assembly RH (rear RH door) or power window regulator motor assembly LH (rear LH door) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B120687

P/W Master SW System Missing Message

No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Multiplex network master switch assembly
  • Wire harness or connector

Main Body

A

B232187

D-Door P/W System Missing Message

No communication between power window regulator motor assembly LH (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Multiplex network master switch assembly
  • Power window regulator motor assembly LH (driver door)
  • Wire harness or connector

Main Body

A

B232287

P-Door P/W System Missing Message

No communication between power window regulator motor assembly RH (front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Power window regulator motor assembly RH (front passenger door)
  • Wire harness or connector

Main Body

A

B232387

RR-Door P/W System Missing Message

No communication between power window regulator motor assembly RH (rear RH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Power window regulator motor assembly RH (rear RH door)
  • Wire harness or connector

Main Body

A

B232487

RL-Door P/W System Missing Message

No communication between power window regulator motor assembly LH (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Power window regulator motor assembly LH (rear LH door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

DTCs are not output

A

B120687, B232187, B232287, B232387 and B232487 are output

B

B120687, B232187, B232387 and B232487 are output

C

B120687, B232187 and B232487 are output

D

B120687 and B232187 are output

E

Only B120687 is output

F

Only B232187 is output

G

Only B232287 is output

H

Only B232387 is output

I

Only B232487 is output

J

A

USE SIMULATION METHOD TO CHECK

C

GO TO STEP 5

D

GO TO STEP 6

E

GO TO STEP 6

F

GO TO STEP 7

G

GO TO STEP 8

H

GO TO STEP 11

I

GO TO STEP 13

J

GO TO STEP 15

B
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

Pre-procedure1

(a) Remove the power distribution box assembly.

HINT:

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without harness connected

(Power Distribution Box Assembly)

-

-

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

Standard Resistance:

Click Location & Routing(z1,R17) Click Connector(z1) Click Connector(R17)

Tester Connection

Condition

Specified Condition

Result

z1-15 (LIN2) - R17-17

Always

Below 1 Ω

Ω

Post-procedure1

(d) None

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR))

Pre-procedure1

(a) Disconnect the M2 power window regulator motor assembly LH (rear LH door) connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,M2) Click Connector(R17) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

R17-17 - M2-9 (LIN)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(c) None

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR))

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the N4 power window regulator motor assembly RH (front passenger door) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,N4) Click Connector(R17) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

R17-17 - N4-9 (LIN)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(d) None

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the O8 multiplex network master switch assembly connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,O8) Click Connector(R17) Click Connector(O8)

Tester Connection

Condition

Specified Condition

Result

R17-17 - O8-3 (LIN1)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(d) None

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

(a) Disconnect the O8 multiplex network master switch assembly connector.

Procedure1

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(O8) Click Connector(O8)

Tester Connection

Condition

Specified Condition

Result

O8-1 (B) - Body ground

Ignition switch off

11 to 14 V

V

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O8) Click Connector(O8)

Tester Connection

Condition

Specified Condition

Result

O8-4 (GND) - Body ground

Always

Below 1 Ω

Ω

Post-procedure1

(d) None

OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

(a) Remove the multiplex network master switch assembly.

HINT:

Click here

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O8) Click Connector(O8)

Tester Connection

Condition

Specified Condition

Result

O8-9 (LIN2) - O8-3 (LIN1)

Always

Below 1 Ω

Ω

Result:

Proceed to

OK

NG

*a

Component without harness connected

(Multiplex Network Master Switch Assembly)

Post-procedure1

(c) None

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR))

Pre-procedure1

(a) Disconnect the O5 power window regulator motor assembly LH (driver door) connector.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(O8,O5) Click Connector(O8) Click Connector(O5)

Tester Connection

Condition

Specified Condition

Result

O8-9 (LIN2) - O5-9 (LIN)

Always

Below 1 Ω

Ω

Post-procedure1

(c) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(O5) Click Connector(O5)

Tester Connection

Condition

Specified Condition

Result

O5-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O5) Click Connector(O5)

Tester Connection

Condition

Specified Condition

Result

O5-1 (GND) - Body ground

Always

Below 1 Ω

Ω

OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR))

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the N4 power window regulator motor assembly RH (front passenger door) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,N4) Click Connector(R17) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

R17-17 - N4-9 (LIN)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(N4) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

N4-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(N4) Click Connector(N4)

Tester Connection

Condition

Specified Condition

Result

N4-1 (GND) - Body ground

Always

Below 1 Ω

Ω

OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR))

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the L2 power window regulator motor assembly RH (rear RH Door) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,L2) Click Connector(R17) Click Connector(L2)

Tester Connection

Condition

Specified Condition

Result

R17-17 - L2-9 (LIN)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(L2) Click Connector(L2)

Tester Connection

Condition

Specified Condition

Result

L2-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(L2) Click Connector(L2)

Tester Connection

Condition

Specified Condition

Result

L2-1 (GND) - Body ground

Always

Below 1 Ω

Ω

OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR))

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect the M2 power window regulator motor assembly LH (rear LH door) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(R17,M2) Click Connector(R17) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

R17-17 - M2-9 (LIN)

Ignition switch off

Below 1 Ω

Ω

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(M2) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

M2-2 (B) - Body ground

Ignition switch off

11 to 14 V

V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(M2) Click Connector(M2)

Tester Connection

Condition

Specified Condition

Result

M2-1 (GND) - Body ground

Always

Below 1 Ω

Ω

OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

LIN Communication Missing Message (B228787)

DESCRIPTION

When an internal malfunction is detected in the certification ECU (smart key ECU assembly), this DTC is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B228787

LIN Communication Missing Message

An internal malfunction occurs in the certification ECU (smart key ECU assembly).

Certification ECU (smart key ECU assembly)

Power Source Control

B

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here

PROCEDURE

  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

B278588 is not output

A

B278588 is output

B

B

GO TO DTC CHART

A
  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Power Source Control > Trouble Codes
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes

Result

Proceed to

B228787 is not output

A

B228787 is output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Door LIN Bus off (B232588)

DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B232588 will be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B232588

Door LIN Bus off

The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Power distribution box assembly
  • Multiplex network master switch assembly
  • Power window regulator motor assembly LH (driver door)
  • Power window regulator motor assembly RH (front passenger door)
  • Power window regulator motor assembly LH (rear LH door)
  • Power window regulator motor assembly RH (rear RH door)
  • Wire harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the O5 power window regulator motor assembly LH (driver door) connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR)

(a) After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B232588 is not output

A

B232588 is not output

B

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR)

A
  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the O8 multiplex network master switch assembly connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

(a) After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B232588 is output

A

B232588 is not output

B

B

GO TO STEP 14

A
  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the N4 power window regulator motor assembly RH (front passenger door) connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR)

(a) After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B232588 is output

A

B232588 is not output

B

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FRONT PASSENGER DOOR)

A
  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the L2 power window regulator motor assembly RH (rear RH door) connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR)

(a) After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B232588 is output

A

B232588 is not output

B

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REAR RH DOOR)

A
  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the M2 power window regulator motor assembly LH (rear LH door) connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR)

(a) After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B232588 is output

A

B232588 is not output

B

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REAR LH DOOR)

A
  1. CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - EACH ECU)

Pre-procedure1

(a) Disconnect the R17 power distribution box assembly connector.

(b) Disconnect all connectors shown in the wiring diagram.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(R17) Click Connector(R17)

Tester Connection

Condition

Specified Condition

Result

R17-17 - Body ground

Always

10 kΩ or higher

kΩ

R17-17 - Other terminals

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT POWER DISTRIBUTION BOX ASSEMBLY

Pre-procedure1

(a) Remove the power distribution box assembly.

HINT:

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without harness connected

(Power Distribution Box Assembly)

-

-

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

Standard Resistance:

Click Location & Routing(R17,K20,K21,z1) Click Connector(R17) Click Connector(K20) Click Connector(K21) Click Connector(z1)

Tester Connection

Condition

Specified Condition

Result

R17-17 - K20-36 or K21-41

Always

10 kΩ or higher

kΩ

z1-15 (LIN2) - Other terminals

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

OK
  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

(a) Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.

HINT:

Click here

(b) Connect all power distribution box assembly connectors other than R17.

Procedure1

(c) Using a GTS, check the waveform.

*a

Component with harness connected

(Power Distribution Box Assembly)

*b

Waveform

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

OK:

Click Location & Routing(R17) Click Connector(R17)

Tester Connection

Condition

Tool Setting

Specified Condition

R17-17 - Body ground

Ignition switch ON

2 V/DIV., 200 ms/DIV.

Pulse generation

(See waveform)

Post-procedure1

(d) None

OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (DRIVER DOOR))

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(O8) Click Connector(O8)

Tester Connection

Condition

Specified Condition

Result

O8-9 (LIN2) - Body ground

Always

10 kΩ or higher

kΩ

O8-9 (LIN2) - Other terminals

Always

10 kΩ or higher

kΩ

OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Alarm / Wiper LIN Bus off (B276C88)

DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B276C88

Alarm / Wiper LIN Bus off

No communication between main body ECU (multiplex network body ECU) and rain sensor for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Rain sensor
  • Harness or connector

Main Body

A

WIRING DIAGRAM

NOTICE:

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

  • When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the Toyota Prius vehicle begins, and then select the vehicle model manually.

    Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key (CAN). While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the Toyota Prius vehicle.

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B276C88 is not output

A

B276C88 is output

B

A

USE SIMULATION METHOD TO CHECK

B
  1. CLEAR DTC

Pre-procedure1

(a) Disconnect the U4 rain sensor connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK RAIN SENSOR

(a) Check if the DTC is output.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

B276C88 is output

A

B276C88 is not output

B

B

REPLACE RAIN SENSOR

A
  1. CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

Pre-procedure1

(a) Disconnect the K16 main body ECU (multiplex network body ECU) connector.

(b) Disconnect the U4 rain sensor connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K16) Click Connector(K16)

Tester Connection

Condition

Specified Condition

Result

K16-11 (LIN4) - Body ground

Always

10 kΩ or higher

kΩ

Post-procedure1

(d) None

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Communication between ECUs connected by LIN Bus off (B278588)

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B278588

Communication between ECUs connected by LIN Bus off

No communication between ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) for 10 seconds or more.

  • Certification ECU (smart key ECU assembly)
  • ID code box (immobiliser code ECU)
  • Wire harness or connector

Smart Key

A

WIRING DIAGRAM

NOTICE:

  • Before performing the inspection, check that DTC B278987 or B278C87 is not output.

    Click here

  • When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the Toyota Prius vehicle begins, and then select the vehicle model manually.

    Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key (CAN). While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the Toyota Prius vehicle.

  • Before replacing the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to Registration.

    Click here

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

Pre-procedure1

(a) Disconnect the K13 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the K43 ID code box (immobiliser code ECU) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(K13,K43) Click Connector(K13) Click Connector(K43)

Tester Connection

Condition

Specified Condition

Result

K13-8 (LIN) - K43-2 (LIN1)

Ignition switch off

Below 1 Ω

Ω

K13-8 (LIN) or K43-2 (LIN1) - Body ground

Ignition switch off

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CLEAR DTC

Pre-procedure1

(a) Connect the K13 certification ECU (smart key ECU assembly) connector.

Procedure1

(b) Clear the DTCs.

Body Electrical > Smart Key > Clear DTCs

Post-procedure1

(c) None

NEXT
  1. CHECK FOR DTC

(a) Recheck for DTCs.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

B278588 is output

A

B278588 is not output

B

A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

ID-BOX Missing Message (B278987)

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B278987

ID-BOX Missing Message

No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.

  • Certification ECU (smart key ECU assembly)
  • ID code box (immobiliser code ECU)
  • Wire harness or connector

Smart Key

A

WIRING DIAGRAM

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • When using the GTS with the ignition switch off, perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less until communication between the GTS and the Toyota Prius vehicle begins, and then select the vehicle model manually.

    Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key (CAN). While using the GTS, periodically perform lock and unlock operations using the door control switch of the multiplex network master switch assembly at intervals of 1.5 seconds or less to maintain communication between the GTS and the Toyota Prius vehicle.

  • Before replacing the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to Registration.

    Click here

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

Pre-procedure1

(a) Disconnect the K13 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the K43 ID code box (immobiliser code ECU) connector.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Click Location & Routing(K13,K43) Click Connector(K13) Click Connector(K43)

Tester Connection

Condition

Specified Condition

Result

K13-8 (LIN) - K43-2 (LIN1)

Ignition switch off

Below 1 Ω

Ω

K13-8 (LIN) or K43-2 (LIN1) - Body ground

Ignition switch off

10 kΩ or higher

kΩ

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - AUXILIARY BATTERY AND BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Click Location & Routing(K43) Click Connector(K43)

Tester Connection

Condition

Specified Condition

Result

K43-1 ( B) - Body ground

Ignition switch off

11 to 14 V

V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Click Location & Routing(K43) Click Connector(K43)

Tester Connection

Condition

Specified Condition

Result

K43-5 (GND) - Body ground

Always

Below 1 Ω

Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

(a) Replace the ID code box (immobiliser code ECU).

HINT:

Click here

NEXT
  1. REGISTER ECU CODE REGISTRATION

(a) Register the recognition codes in the ECUs.

HINT:

Click here

NEXT
  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Smart Key > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Recheck for DTCs.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

B278987 is not output

A

B278987 is output

B

A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Power Source Control System Missing Message (B278C87)

DESCRIPTION

When an internal malfunction is detected in the certification ECU (smart key ECU assembly), this DTC is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B278C87

Power Source Control System Missing Message

An internal malfunction occurs in the certification ECU (smart key ECU assembly).

Certification ECU (smart key ECU assembly)

Smart Key

A

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

Click here

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Smart Key > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

B278C87 is not output

A

B278C87 is output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)