Mass Air Flow Meter
- On-vehicle Inspection
- Removal
- Installation
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
Pre-procedure1
(a) Read the value of Data List item "Mass Air Flow Sensor" using the GTS.
NOTICE:
Perform the inspection of the mass air flow meter sub-assembly while it is installed to the air cleaner cap sub-assembly (installed to the Toyota Prius vehicle).
(1) Check and ensure the following conditions:
- Turn off all electrical loads, such as the air conditioning, etc.
- Check that the coolant temperature is 75 °C or more.
- Put the shift lever in the N position.
(2) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(3) Start the engine.
Procedure1
(b) According to the display on the GTS, read the Data List when the engine is running.
Powertrain > Engine > Data ListMass Air Flow Sensor
Standard Condition:
GTS Display | Condition | Specified Condition | Result |
|---|---|---|---|
Mass Air Flow Sensor |
Idling with warmed up engine (inspection mode [maintenance mode], not charge control) |
1.0 to 3.0 gm/sec |
gm/sec |
Mass Air Flow Sensor |
Warmed up engine, 2500 rpm (inspection mode [maintenance mode]) |
4.5 to 8.5 gm/sec |
gm/sec |
If the result is not as specified, clean the mass air flow meter sub-assembly.
If the result is within the specified range, inspect the mass air flow meter sub-assembly.
Click here ![]()
Post-procedure1
(c) None
2. CLEAN MASS AIR FLOW METER SUB-ASSEMBLY
NOTICE:
If the mass air flow meter sub-assembly is removed and installed 10 times or more, the thread of the hole of the mass air flow meter sub-assembly may be damaged. Therefore, do not loosen the screws of the mass air flow meter sub-assembly.
Pre-procedure1
(a) Remove the air cleaner cap sub-assembly.
Procedure1

*1 |
Mass Air Flow Meter Sub-assembly |
*a |
Air Blow Gun |
*b |
10 mm (0.394 in.) |
*c |
Airflow Hole |
(b) Clean the mass air flow meter sub-assembly.
NOTICE:
- Do not contact the mass air flow meter sub-assembly with the nozzle of the air blow gun.
- Do not insert the nozzle of the air blow gun into the airflow hole.
(1) Using an air blow gun, clean the hole of the mass air flow meter sub-assembly by applying approximately 10 intermittent bursts of air to the airflow hole at a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi). |
|
Post-procedure1
(c) Install the air cleaner cap sub-assembly.
3. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
HINT:
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during mass air flow meter sub-assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Replacement of mass air flow meter sub-assembly |
Inspection after repair |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
MASS AIR FLOW METER SUB-ASSEMBLY |
22204 |
- |
- |
|
PROCEDURE
1. REMOVE MASS AIR FLOW METER SUB-ASSEMBLY
![]() |
NOTICE: If the mass air flow meter sub-assembly has been struck or dropped, replace it. |

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
MASS AIR FLOW METER SUB-ASSEMBLY |
22204 |
- |
- |
|
2 |
PERFORM INITIALIZATION |
- |
- |
- |
|
PROCEDURE
1. INSTALL MASS AIR FLOW METER SUB-ASSEMBLY
![]() |
NOTICE:
|
2. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click here ![]()












