Rear Coil Spring
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear coil spring removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: Also necessary after performing a tire rotation. *2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location. *3: The Toyota Prius vehicle height changes because of suspension or tire replacement. |
|||
Rear wheel alignment adjustment |
Perform "Calibration" |
|
|
Tires |
|
Tire Pressure Warning System |
Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) |
Rear television camera assembly optical axis (Back camera position setting)*3 |
Parking Assist Monitor System |
||
Parking assist ECU initialization*3 |
Panoramic View Monitor System |
||
Advanced Park |
|||
Suspension parts |
Rear television camera assembly optical axis (Back camera position setting) |
Parking Assist Monitor System |
|
Parking assist ECU initialization |
Panoramic View Monitor System |
||
Advanced Park |
|||
HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR FLOOR SIDE MEMBER COVER LH |
57628E |
- |
- |
- |
2 |
REAR FLOOR SIDE MEMBER COVER RH |
57627G |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
REAR WHEEL |
- |
- |
- |
- |
4 |
REAR STABILIZER BAR (for 2WD with Stabilizer Bar) |
48812 |
- |
- |
|
5 |
REAR STABILIZER BAR (for AWD) |
48812 |
- |
- |
|
6 |
REAR COIL SPRING |
48231B |
- |
- |
|
7 |
REAR UPPER COIL SPRING INSULATOR |
48259A |
- |
- |
- |
8 |
REAR LOWER COIL SPRING INSULATOR |
48258C |
- |
- |
- |
*A |
for 2WD |
*B |
for AWD |
*C |
for 2WD with Stabilizer Bar |
- |
- |
*1 |
REAR NO. 2 SUSPENSION ARM ASSEMBLY |
*2 |
REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY |
*3 |
NO. 2 CAMBER ADJUST CAM |
- |
- |
PROCEDURE
1. REMOVE REAR FLOOR SIDE MEMBER COVER LH
Click here ![]()
2. REMOVE REAR FLOOR SIDE MEMBER COVER RH
Click here ![]()
3. REMOVE REAR WHEEL
Click here ![]()
4. REMOVE REAR STABILIZER BAR (for 2WD with Stabilizer Bar)
![]() |
Click here |
5. REMOVE REAR STABILIZER BAR (for AWD)
![]() |
Click here |
6. REMOVE REAR COIL SPRING

*A |
for 2WD |
*B |
for AWD |
*a |
Matchmark |
*b |
Wooden Block |
*c |
Jack |
- |
- |
(1) Place matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.
(2) Loosen the nut (rear suspension member sub-assembly side) of the rear No. 2 suspension arm assembly.
NOTICE:
Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.
(3) Using a jack and wooden block, support the rear No. 2 suspension arm assembly.
NOTICE:
- When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
- Make sure to perform this operation with the Toyota Prius vehicle kept as low as possible.
(4) Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly from the rear axle carrier sub-assembly.
NOTICE:
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
(5) Slowly lower the rear No. 2 suspension arm assembly, and then remove the rear coil spring.
7. REMOVE REAR UPPER COIL SPRING INSULATOR

8. REMOVE REAR LOWER COIL SPRING INSULATOR

Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR UPPER COIL SPRING INSULATOR |
48259A |
- |
- |
- |
2 |
REAR LOWER COIL SPRING INSULATOR |
48258C |
- |
- |
- |
3 |
REAR COIL SPRING |
48231B |
- |
- |
|
4 |
REAR STABILIZER BAR (for HEV Model 2WD with Stabilizer Bar) |
48812 |
- |
- |
|
5 |
REAR STABILIZER BAR (for HEV Model AWD, PHEV Model) |
48812 |
- |
- |
|
6 |
STABILIZE SUSPENSION |
- |
- |
- |
|
7 |
REAR NO. 2 SUSPENSION ARM ASSEMBLY |
48740F |
- |
- |
|
8 |
REAR STABILIZER LINK ASSEMBLY LH (w/ Stabilizer Bar) |
48840A |
- |
- |
|
9 |
REAR STABILIZER LINK ASSEMBLY RH (w/ Stabilizer Bar) |
48830D |
- |
- |
|
10 |
REAR WHEEL |
- |
- |
- |
- |
11 |
REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY |
48409 |
- |
- |
|
*A |
for HEV Model 2WD |
*B |
for HEV Model AWD, PHEV Model |
*C |
for HEV Model 2WD with Stabilizer Bar |
*D |
w/ Stabilizer Bar |
*1 |
NO. 2 CAMBER ADJUST CAM |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
12 |
REAR FLOOR SIDE MEMBER COVER LH |
57628E |
- |
- |
- |
13 |
REAR FLOOR SIDE MEMBER COVER RH |
57627G |
- |
- |
- |
14 |
BATTERY BOX COVER |
58219K |
- |
- |
- |
15 |
INSPECT AND ADJUST REAR WHEEL ALIGNMENT |
- |
- |
- |
|
16 |
PERFORM INITIALIZATION |
- |
- |
- |
|
*A |
for PHEV Model |
*B |
for HEV Model |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL REAR UPPER COIL SPRING INSULATOR
2. INSTALL REAR LOWER COIL SPRING INSULATOR
3. INSTALL REAR COIL SPRING

*a |
Identification Mark |
*b |
30° or less |
*c |
Lower End of Rear Coil Spring |
- |
- |
![]() |
Inner Side of the Toyota Prius Vehicle |
- |
- |
(1) Set the rear coil spring to the rear No. 2 suspension arm assembly.
NOTICE:
- Set the rear coil spring so that its lower end is within the range shown in the illustration.
- Set the rear coil spring so that the identification mark is positioned as shown in the illustration.
- The smaller diameter end must face upward.
(2) Using a jack and wooden block, slowly jack up the rear No. 2 suspension arm assembly and then install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.
CAUTION:
Do not jack up the rear No. 2 suspension arm assembly too high as the Toyota Prius vehicle may fall.
NOTICE:
- Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
- When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
- Make sure to perform this operation with the vehicle kept as low as possible.
- Insert the bolt with the threaded end facing the front of the Toyota Prius vehicle.
4. INSTALL REAR STABILIZER BAR (for HEV Model 2WD with Stabilizer Bar)
![]() |
Click here |
5. INSTALL REAR STABILIZER BAR (for HEV Model AWD, PHEV Model)
![]() |
Click here |
6. STABILIZE SUSPENSION
![]() |
Click here |
7. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

(1) Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.
Torque:
73 N·m {744 kgf·cm, 54 ft·lbf}
NOTICE:
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
8. INSTALL REAR STABILIZER LINK ASSEMBLY LH (w/ Stabilizer Bar)
![]() |
Click here |
9. INSTALL REAR STABILIZER LINK ASSEMBLY RH (w/ Stabilizer Bar)
10. INSTALL REAR WHEEL
Click here ![]()
11. INSTALL REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY
![]() |
for 2WD: Click here for AWD LH Side: Click here for AWD RH Side: Click here for PHEV: Click here |
12. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for HEV Model)
Click here ![]()
13. INSTALL REAR FLOOR SIDE MEMBER COVER RH (for HEV Model)
Click here ![]()
14. INSTALL BATTERY BOX COVER (for PHEV Model)
Click here ![]()
15. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
Click here ![]()
16. PERFORM INITIALIZATION
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Advanced Park |













































