Electric Parking Brake Actuator
Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
RELEASE PARKING BRAKE |
- |
- |
- |
|
3 |
REAR WHEEL |
- |
- |
- |
- |
4 |
NO. 2 PARKING BRAKE WIRE ASSEMBLY |
890C0A |
- |
- |
|
5 |
PARKING BRAKE ACTUATOR ASSEMBLY |
46310B |
- |
- |
|
6 |
PARKING BRAKE ACTUATOR SEAL |
46310C |
- |
- |
- |
● |
Non-reusable part |
- |
- |
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
Click here ![]()
2. RELEASE PARKING BRAKE

(1) Perform the following procedure.
1. Move the shift lever to P.
2. Turn the ignition switch to ON.
3. Operate the electric parking brake switch assembly to release the parking brake.
HINT:
If the parking brake cannot be released:
Click here ![]()
4. Turn the ignition switch off.
3. REMOVE REAR WHEEL
Click here ![]()
4. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(1) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
NOTICE:
- Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
- Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
5. REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

(1) Using a 5 mm hexagon socket wrench, remove the 2 bolts and parking brake actuator assembly from the rear disc brake cylinder assembly.
NOTICE:
- Check for brake fluid leaks on the back side of the rear disc brake cylinder assembly.
- If there are any brake fluid leaks, replace the rear disc brake cylinder assembly.
6. REMOVE PARKING BRAKE ACTUATOR SEAL

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PARKING BRAKE ACTUATOR SEAL |
46310C |
- |
- |
|
2 |
PARKING BRAKE ACTUATOR ASSEMBLY |
46310B |
- |
- |
|
3 |
NO. 2 PARKING BRAKE WIRE ASSEMBLY |
890C0A |
- |
- |
|
4 |
REAR WHEEL |
- |
- |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
![]() |
Lithium soap base glycol grease |
- |
- |
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL PARKING BRAKE ACTUATOR SEAL

(1) Apply a light coat of lithium soap base glycol grease to a new parking brake actuator seal.
(2) Install the parking brake actuator seal to the rear disc brake cylinder assembly.
NOTICE:
Make sure to replace the parking brake actuator seal with a new one when installing the parking brake actuator assembly.
2. INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

(1) Using a 5 mm hexagon socket wrench, install the parking brake actuator assembly to the rear disc brake cylinder assembly with the 2 bolts.
Torque:
8,4 N·m {86 kgf·cm, 74 in·lbf}
3. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
![]() |
NOTICE:
|
4. INSTALL REAR WHEEL
Click here ![]()















