Exhaust Manifold
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
Inspection after repair |
|
CAUTION:
- To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

- To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
WINDSHIELD WIPER MOTOR AND LINK |
- |
- |
- |
- |
2 |
WATER GUARD PLATE |
55734D |
- |
- |
- |
3 |
OUTER COWL TOP PANEL SUB-ASSEMBLY |
55701J |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
4 |
AIR FUEL RATIO SENSOR |
89467B |
- |
- |
|
5 |
FRONT FLOOR COVER LH |
58166A |
- |
- |
|
6 |
FRONT FLOOR COVER RH |
58165C |
- |
- |
|
7 |
FRONT FLOOR CENTER BRACE |
57533B |
- |
- |
- |
8 |
FRONT EXHAUST PIPE ASSEMBLY |
17410 |
- |
- |
|
9 |
FRONT NO. 1 FLOOR HEAT INSULATOR |
58151 |
- |
- |
- |
10 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
11 |
WIRING HARNESS CLAMP BRACKET |
- |
- |
- |
|
12 |
NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
17617 |
- |
- |
|
13 |
MANIFOLD STAY |
17118 |
- |
- |
|
14 |
EXHAUST MANIFOLD |
17141 |
- |
- |
|
15 |
NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
17168 |
- |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE WINDSHIELD WIPER MOTOR AND LINK
Click here ![]()
2. REMOVE WATER GUARD PLATE
Click here ![]()
3. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
Click here ![]()
4. REMOVE AIR FUEL RATIO SENSOR
![]() |
Click here |
5. REMOVE FRONT FLOOR COVER LH

(1) Remove the bolt, 2 nuts, and 2 clips.
(2) Turn the clip and remove the front floor cover LH from the Toyota Prius vehicle body.
NOTICE:
If the clip is not turned when the front floor cover LH is removed, the front floor cover LH or stud bolt may be damaged.
HINT:
Do not remove the clip from the front floor cover LH.
6. REMOVE FRONT FLOOR COVER RH

(1) Remove the bolt, 2 nuts, and 2 clips.
(2) Turn the clip and remove the front floor cover RH from the Toyota Prius vehicle body.
NOTICE:
If the clip is not turned when the front floor cover RH is removed, the front floor cover RH or stud bolt may be damaged.
HINT:
Do not remove the clip from the front floor cover RH.
7. REMOVE FRONT FLOOR CENTER BRACE

8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
![]() |
CAUTION: To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot. |

9. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

10. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
11. REMOVE WIRING HARNESS CLAMP BRACKET
![]() |
CAUTION: To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot. |

12. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
![]() |
CAUTION: To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot. |

13. REMOVE MANIFOLD STAY
![]() |
CAUTION: To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot. |

14. REMOVE EXHAUST MANIFOLD
![]() |
CAUTION: To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot. |

15. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Installation
INSTALLATION

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
17168 |
- |
- |
- |
2 |
EXHAUST MANIFOLD |
17141 |
- |
- |
|
3 |
MANIFOLD STAY |
17118 |
- |
- |
|
4 |
NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
17617 |
- |
- |
- |
5 |
WIRING HARNESS CLAMP BRACKET |
- |
- |
- |
- |
6 |
FRONT NO. 1 FLOOR HEAT INSULATOR |
58151 |
- |
- |
- |
7 |
FRONT EXHAUST PIPE ASSEMBLY |
17410 |
- |
- |
|
8 |
FRONT FLOOR CENTER BRACE |
57533B |
- |
- |
- |
9 |
FRONT FLOOR COVER RH |
58165C |
- |
- |
- |
10 |
FRONT FLOOR COVER LH |
58166A |
- |
- |
- |
11 |
SENSOR, AIR FUEL RATIO |
89467B |
- |
- |
|
12 |
INSPECT FOR EXHAUST GAS LEAK |
- |
- |
- |
|
13 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
* |
For use with SST |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
14 |
OUTER COWL TOP PANEL SUB-ASSEMBLY |
55701J |
- |
- |
- |
15 |
WATER GUARD PLATE |
55734D |
- |
- |
- |
16 |
WINDSHIELD WIPER MOTOR AND LINK |
- |
- |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
PROCEDURE
1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
2. INSTALL EXHAUST MANIFOLD

(1) Install a new exhaust manifold to head gasket and EGR cooler gasket to the cylinder head sub-assembly.
(2) Temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.
(3) Using a 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.
Torque:
26 N·m {265 kgf·cm, 19 ft·lbf}
3. INSTALL MANIFOLD STAY

(1) Tighten the 3 bolts in the order shown in the illustration.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
5. INSTALL WIRING HARNESS CLAMP BRACKET
Torque:
39 N·m {398 kgf·cm, 29 ft·lbf}
6. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
Torque:
5 N·m {51 kgf·cm, 44 in·lbf}
7. INSTALL FRONT EXHAUST PIPE ASSEMBLY

*1 |
Exhaust Manifold or Front Exhaust Pipe Assembly |
*2 |
Gasket |
*a |
Wooden Block |
*b |
Plastic Hammer |
(1) Using a vernier caliper, measure the free length of the compression springs.
Standard Length (Front) |
43 mm (1.69 in.) |
Standard Length (Rear) |
40 mm (1.57 in.) |
Minimum Free Length (Front) |
41.5 mm (1.63 in.) |
Minimum Free Length (Rear) |
38.5 mm (1.52 in.) |
If the free length is less than the minimum, replace the compression spring.
(2) temporarily install 2 new gaskets to the exhaust manifold and front exhaust pipe assembly.
(3) Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.
NOTICE:
- Be sure to install the gasket in the correct direction.
- Do not reuse the gaskets.
- Do not damage the gaskets.
- Do not push in the gaskets by using the exhaust pipes when connecting them.

*1 |
Exhaust Manifold |
*2 |
Front Exhaust Pipe Assembly |
*3 |
Tail Exhaust Pipe Assembly |
*4 |
Gasket |
*a |
Space between Flanges: 8.5 mm (0.335in.) |
*b |
Space between Flanges: 6.5 mm (0.256in.) |
(1) Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.
(2) Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
(3) After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly is consistent front-to-rear and left-to-right.
(4) Install the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
(5) After installation, check that the space between the flanges of the front exhaust pipe assembly and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.
(6) Engage the wire harness clamp.
(7) Connect the heated oxygen sensor connector.
8. INSTALL FRONT FLOOR CENTER BRACE
Torque:
27 N·m {275 kgf·cm, 20 ft·lbf}
9. INSTALL FRONT FLOOR COVER RH
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
10. INSTALL FRONT FLOOR COVER LH
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
11. INSTALL AIR FUEL RATIO SENSOR
![]() |
Click here |
12. INSPECT FOR EXHAUST GAS LEAK
Click here ![]()
13. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
14. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Torque:
Bolt :
12 N·m {122 kgf·cm, 9 ft·lbf}
Nut :
50 N·m {510 kgf·cm, 37 ft·lbf}
15. INSTALL WATER GUARD PLATE
16. INSTALL WINDSHIELD WIPER MOTOR AND LINK
Click here ![]()



































