Headlight Assembly

In this manual: Headlight Assembly
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~31min read
5special tools
0102030405075N·mlb·ft
Tightening torque found on this page
  • Precaution
  • Removal
  • Disassembly
  • Inspection
  • Adjustment
  • Reassembly
  • Installation

Precaution

PRECAUTION

NOTICE:

When disassembling the headlight assembly, use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

STATIC ELECTRICITY COUNTERMEASURES SST

SST: Desktop anti-static mat set (09890-47010)

  • Wristband

    SST:

    09891-04020

  • Wristband connection wire (No. 1 grounding wire)

    SST:

    09891-04030

  • Anti-static mat

    SST:

    09891-04010

  • Ground connection wire (No. 2 grounding wire)

    SST:

    09891-04040

PRECAUTIONS DURING REPLACEMENT

(a) Precautions during procedures:

(1) Before performing any procedures, touch an unpainted metal part or ground bolt of the Toyota Prius vehicle to eliminate any static electricity.

(2) To prevent damage to electrical equipment, disconnect the battery power supply before installing and removing electrical equipment.

(3) Never touch the electronic parts of a printed wire board or the pins of an integrated circuit.

(4) When performing procedures, do not allow clothing to come near or contact parts.

(b) Wear SST (wristband) firmly on your wrist.

SST:

09891-04020

(c) Connect SST (No. 2 grounding wire) and SST (anti-static mat) to an appropriate grounding point in the workspace and on the work table.

SST:

09891-04040

09891-04010

HINT:

When working inside the Toyota Prius vehicle:

Connect SST (No. 2 grounding wire) to an unpainted metal part or a ground bolt, etc.

(d) Connect SST (No. 1 grounding wire), SST (wristband) and SST (anti-static mat).

SST:

09891-04030

(e) Always place the headlight assembly and its components on SST (anti-static mat).

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*1

Front television camera view adjustment

Panoramic View Monitor System

Advanced Park

Replacement or removal and installation of 2 or more parts:
  • Front television camera assembly, Radiator grille or Front bumper assembly
  • Rear television camera assembly
  • Side television camera assembly LH, Parking assist light LH or Outer rear view mirror assembly LH
  • Side television camera assembly RH, Parking assist light RH or Outer rear view mirror assembly RH

Television camera view adjustment

Panoramic View Monitor System

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
  • w/ Front Side Radar:

    If the headlight assembly is damaged or deformed due to an accident, contact, etc., and repairs have been made to the area of the body to which the headlight assembly is installed, it is necessary to perform front side radar sensor adjustment.

    for Driving Adjustment: Click here

    for Target Adjustment (Triangle Target): Click here

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

FRONT BUMPER ASSEMBLY

-

-

-

-

2

FRONT SIDE RADAR SENSOR

882B1

-

-

3

HEADLIGHT ASSEMBLY

-

-

-

*A

w/ Front Side Radar

-

-

PROCEDURE

1. REMOVE FRONT BUMPER ASSEMBLY

Click here

2. REMOVE FRONT SIDE RADAR SENSOR (w/ Front Side Radar)

Click here

3. REMOVE HEADLIGHT ASSEMBLY

*a

Bolt

*b

Screw

Protective Tape

Disengage in this Direction

(1) Apply protective tape around the headlight assembly as shown in the illustration.

(2) Remove the bolt and 3 screws.

(3) Disengage the 3 guides as shown in the illustration.

(4) Disconnect the 2 connectors and disengage the 2 clamps to remove the headlight assembly.

Disassembly

DISASSEMBLY

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (DISASSEMBLY)

Procedure

Part Name Code

1

HEADLIGHT FRONT TURN SIGNAL LED

8113A

-

-

-

2

HEADLIGHT BRACKET

53246B

-

-

-

3

FRONT SIDE RADAR SENSOR BRACKET

88215C

-

-

-

*A

w/ Front Turn Signal LED Socket

*B

w/ Front Side Radar

*1

HEADLIGHT UNIT SUB-ASSEMBLY

-

-

Procedure

Part Name Code

4

HEADLIGHT LENS

81186

-

-

5

HEADLIGHT LENS GASKET

81132B

-

-

6

INNER LENS ASSEMBLY

-

-

-

-

7

REFLECTOR

-

-

-

-

8

INNER ASSEMBLY

-

-

-

9

HEADLIGHT UNIT

81175

-

-

10

HEADLIGHT LEVELING MOTOR

85691

-

-

-

11

LIGHT CONTROL LED ECU

85967D

-

-

-

*1

HEADLIGHT LEVELING MOTOR WITH BRACKET

*2

HEADLIGHT LEVELING MOTOR BRACKET

●

Non-reusable part

-

-

PROCEDURE

1. REMOVE HEADLIGHT FRONT TURN SIGNAL LED (w/ Front Turn Signal LED Socket)

2. REMOVE HEADLIGHT BRACKET

3. REMOVE FRONT SIDE RADAR SENSOR BRACKET (w/ Front Side Radar)

4. REMOVE HEADLIGHT LENS

NOTICE:

  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not allow dirt or foreign matter to get on the headlight lens.
  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

SST: 09890-47010

09891-04010

09891-04020

09891-04030

09891-04040

*a

"TORX" screw

*b

Screw

(1) Remove the 6 screws.

(2) Using a T20H "TORX" driver, remove the "TORX" screw.

*a

Separation Starting Point

-

-

(1) Disengage the 8 claws.

(2) Using a dryer, warm the headlight lens gasket from the backside of the headlight unit assembly at the separation starting point of the headlight lens and headlight housing.

NOTICE:

If the headlight unit assembly is heated unevenly, it will deform or melt.

Headlight Lens

Separation Starting Point

Headlight Lens Gasket

Headlight Housing

(1) Insert a finger between the headlight lens and headlight housing and lift up the headlight lens.

HINT:

  • With all of the claws disengaged, lift up the headlight lens.
  • When the headlight lens is lifted up, the claws may re-engage.

(2) Using a screwdriver with its tip wrapped with protective tape, pull out the headlight lens gasket through the opening.

NOTICE:

Do not damage the groove in the headlight housing or the headlight lens.

Separation Starting Point

Headlight Lens Gasket

Pull out in this Direction

Remove in this Direction

(1) Pull out the headlight lens gasket as shown in the illustration to remove the headlight lens.

HINT:

  • With all of the claws disengaged, lift up the headlight lens.
  • When the headlight lens is lifted up, the claws may re-engage.
  • Before lifting up the headlight lens, check that the surrounding claws have not re-engaged.
  • If the headlight lens gasket is disconnected while being pulled out, lift up the headlight lens and pull the headlight lens gasket again.

(2) Remove the headlight lens from the headlight housing from the separation starting point toward the outside of the Toyota Prius vehicle as shown in the illustration.

5. REMOVE HEADLIGHT LENS GASKET

NOTICE:

  • The headlight lens gasket must not be reused.
  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

*A

Headlight Lens Side

*B

Headlight Housing Side

Headlight Lens Gasket

-

-

(1) Remove the remaining headlight lens gasket from the headlight lens and headlight housing.

6. REMOVE INNER LENS ASSEMBLY

7. REMOVE REFLECTOR

8. REMOVE INNER ASSEMBLY

Place Hand Here

Remove in this Direction

(1) Remove the 5 screws.

(2) Disengage the clip to remove the inner assembly as shown in the illustration.

9. REMOVE HEADLIGHT UNIT

NOTICE:

  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not allow dirt or foreign matter to get on the headlight unit or other components.
  • Prevention of static electricity is required during this procedure.
  • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
  • Do not touch the headlight unit with bare hands.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

SST: 09890-47010

09891-04010

09891-04020

09891-04030

09891-04040

(1) Using a vernier caliper, record the dimensions of a and b shown in the illustration.

Turn in this Direction

Remove in this Direction

(1) Disconnect the connector.

(2) Disengage the 2 claws.

(3) While holding the headlight unit assembly by hand, turn the aiming screws as shown in the illustration until the aiming screws are separated from the headlight unit.

(4) Remove the pivot collar as shown in the illustration.

10. REMOVE HEADLIGHT LEVELING MOTOR

*a

Connector

*b

Screw

Remove in this Direction

-

-

11. REMOVE LIGHT CONTROL LED ECU

Inspection

INSPECTION

PROCEDURE

1. INSPECT HEADLIGHT HOUSING LH (w/ Front Turn Signal LED Socket)

(a) Measure the resistance according to the value(s) in the table below.

*1

Headlight Housing LH (Headlight Cord)

-

-

*a

Component without harness connected

(to No. 1 Headlight Clearance LED LH)

*b

Component without harness connected

(to Wire Harness)

*c

Component without harness connected

(to Headlight Leveling Motor LH)

*d

Component without harness connected

(to Headlight Unit LH)

*e

Component without harness connected

(to Light Control ECU)

*f

Component without harness connected

(to Headlight Turn Signal LED Unit)

(1) Inspect the clearance light/daytime running light circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

A-1 - F-5

Always

Below 1 Ω

Ω

A-2 - E-6

Always

Below 1 Ω

Ω

E-7 - F-1

Always

Below 1 Ω

Ω

E-12 - F-8

Always

Below 1 Ω

Ω

E-13 - F-9

Always

Below 1 Ω

Ω

E-14 - F-2

Always

Below 1 Ω

Ω

E-17 - F-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(2) Inspect the Lo/Hi beam circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

D-1 - E-16

Always

Below 1 Ω

Ω

D-2 - E-10

Always

Below 1 Ω

Ω

D-3 - E-15

Always

Below 1 Ω

Ω

D-4 - E-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(3) Inspect the headlight leveling motor circuit.

Standard Resistance:

Click Location & Routing(A38) Click Connector(A38)

Tester Connection

Condition

Specified Condition

Result

A38-2 (B) - C-3

Always

Below 1 Ω

Ω

A38-3 (LHM ) - C-2

Always

Below 1 Ω

Ω

A38-4 (LH T) - C-1

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(4) Inspect the light control ECU power source circuit.

Standard Resistance:

Click Location & Routing(A38) Click Connector(A38)

Tester Connection

Condition

Specified Condition

Result

A38-2 (B) - E-8

Always

Below 1 Ω

Ω

A38-5 (AT1) - E-19

Always

Below 1 Ω

Ω

A38-6 (LO) - E-11

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

2. INSPECT HEADLIGHT HOUSING LH (w/o Front Turn Signal LED Socket)

(a) Measure the resistance according to the value(s) in the table below.

*1

Headlight Housing LH (Headlight Cord)

-

-

*a

Component without harness connected

(to No. 1 Headlight Clearance LED LH)

*b

Component without harness connected

(to Wire Harness)

*c

Component without harness connected

(to Headlight Turn Signal LED Unit)

*d

Component without harness connected

(to No. 2 Headlight Clearance LED LH)

*e

Component without harness connected

(to Headlight Leveling Motor LH)

*f

Component without harness connected

(to Headlight Unit LH)

*g

Component without harness connected

(to Light Control ECU)

*h

Component without harness connected

(to No. 3 Headlight Clearance LED LH)

(1) Inspect the clearance light/daytime running light circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

A-1 - H-7

Always

Below 1 Ω

Ω

A-2 - G-6

Always

Below 1 Ω

Ω

D-1 - G-20

Always

Below 1 Ω

Ω

D-2 - G-3

Always

Below 1 Ω

Ω

G-7 - H-10

Always

Below 1 Ω

Ω

G-12 - H-1

Always

Below 1 Ω

Ω

G-13 - H-2

Always

Below 1 Ω

Ω

G-14 - H-11

Always

Below 1 Ω

Ω

G-17 - H-8

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(2) Inspect the turn signal light circuit.

Standard Resistance:

Click Location & Routing(A38) Click Connector(A38)

Tester Connection

Condition

Specified Condition

Result

A38-1 (E) - C-2

Always

Below 1 Ω

Ω

A38-2 (B) - C-3

Always

Below 1 Ω

Ω

C-4 - H-5

Always

Below 1 Ω

Ω

C-5 - H-3

Always

Below 1 Ω

Ω

C-6 - H-4

Always

Below 1 Ω

Ω

C-8 - H-6

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(3) Inspect the Lo/Hi beam circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

F-1 - G-16

Always

Below 1 Ω

Ω

F-2 - G-10

Always

Below 1 Ω

Ω

F-3 - G-15

Always

Below 1 Ω

Ω

F-4 - G-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(4) Inspect the headlight leveling motor circuit.

Standard Resistance:

Click Location & Routing(A38) Click Connector(A38)

Tester Connection

Condition

Specified Condition

Result

A38-2 (B) - E-3

Always

Below 1 Ω

Ω

A38-3 (LHM ) - E-2

Always

Below 1 Ω

Ω

A38-4 (LH T) - E-1

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

(5) Inspect the light control ECU power source circuit.

Standard Resistance:

Click Location & Routing(A38) Click Connector(A38)

Tester Connection

Condition

Specified Condition

Result

A38-2 (B) - G-8

Always

Below 1 Ω

Ω

A38-5 (AT1) - G-19

Always

Below 1 Ω

Ω

A38-6 (LO) - G-11

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing LH (headlight cord).

3. INSPECT HEADLIGHT HOUSING RH (w/ Front Turn Signal LED Socket)

(a) Measure the resistance according to the value(s) in the table below.

*1

Headlight Housing RH (Headlight Cord)

-

-

*a

Component without harness connected

(to No. 1 Headlight Clearance LED RH)

*b

Component without harness connected

(to Wire Harness)

*c

Component without harness connected

(to Headlight Leveling Motor RH)

*d

Component without harness connected

(to Headlight Unit RH)

*e

Component without harness connected

(to Light Control ECU)

*f

Component without harness connected

(to Headlight Turn Signal LED Unit)

(1) Inspect the clearance light/daytime running light circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

A-1 - F-5

Always

Below 1 Ω

Ω

A-2 - E-6

Always

Below 1 Ω

Ω

E-7 - F-1

Always

Below 1 Ω

Ω

E-12 - F-8

Always

Below 1 Ω

Ω

E-13 - F-9

Always

Below 1 Ω

Ω

E-14 - F-2

Always

Below 1 Ω

Ω

E-17 - F-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(2) Inspect the Lo/Hi beam circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

D-1 - E-16

Always

Below 1 Ω

Ω

D-2 - E-10

Always

Below 1 Ω

Ω

D-3 - E-15

Always

Below 1 Ω

Ω

D-4 - E-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(3) Inspect the headlight leveling motor circuit.

Standard Resistance:

Click Location & Routing(A36) Click Connector(A36)

Tester Connection

Condition

Specified Condition

Result

A36-2 (B) - C-3

Always

Below 1 Ω

Ω

A36-3 (RHM ) - C-2

Always

Below 1 Ω

Ω

A36-4 (RH T) - C-1

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(4) Inspect the light control ECU power source circuit.

Standard Resistance:

Click Location & Routing(A36) Click Connector(A36)

Tester Connection

Condition

Specified Condition

Result

A36-2 (B) - E-8

Always

Below 1 Ω

Ω

A36-5 (AS1) - E-19

Always

Below 1 Ω

Ω

A36-6 (LO) - E-11

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

4. INSPECT HEADLIGHT HOUSING RH (w/o Front Turn Signal LED Socket)

(a) Measure the resistance according to the value(s) in the table below.

*1

Headlight Housing RH (Headlight Cord)

-

-

*a

Component without harness connected

(to No. 1 Headlight Clearance LED RH)

*b

Component without harness connected

(to Wire Harness)

*c

Component without harness connected

(to Headlight Turn Signal LED Unit)

*d

Component without harness connected

(to No. 2 Headlight Clearance LED RH)

*e

Component without harness connected

(to Headlight Leveling Motor RH)

*f

Component without harness connected

(to Headlight Unit RH)

*g

Component without harness connected

(to Light Control ECU)

*h

Component without harness connected

(to No. 3 Headlight Clearance LED RH)

(1) Inspect the clearance light/daytime running light circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

A-1 - H-4

Always

Below 1 Ω

Ω

A-2 - G-6

Always

Below 1 Ω

Ω

D-1 - G-20

Always

Below 1 Ω

Ω

D-2 - G-3

Always

Below 1 Ω

Ω

G-7 - H-1

Always

Below 1 Ω

Ω

G-12 - H-10

Always

Below 1 Ω

Ω

G-13 - H-11

Always

Below 1 Ω

Ω

G-14 - H-2

Always

Below 1 Ω

Ω

G-17 - H-5

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(2) Inspect the turn signal light circuit.

Standard Resistance:

Click Location & Routing(A36) Click Connector(A36)

Tester Connection

Condition

Specified Condition

Result

A36-1 (E) - C-2

Always

Below 1 Ω

Ω

A36-2 (B) - C-3

Always

Below 1 Ω

Ω

C-4 - H-6

Always

Below 1 Ω

Ω

C-5 - H-8

Always

Below 1 Ω

Ω

C-6 - H-9

Always

Below 1 Ω

Ω

C-8 - H-7

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(3) Inspect the Lo/Hi beam circuit.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Result

F-1 - G-16

Always

Below 1 Ω

Ω

F-2 - G-10

Always

Below 1 Ω

Ω

F-3 - G-15

Always

Below 1 Ω

Ω

F-4 - G-4

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(4) Inspect the headlight leveling motor circuit.

Standard Resistance:

Click Location & Routing(A36) Click Connector(A36)

Tester Connection

Condition

Specified Condition

Result

A36-2 (B) - E-3

Always

Below 1 Ω

Ω

A36-3 (RHM ) - E-2

Always

Below 1 Ω

Ω

A36-4 (RH T) - E-1

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

(5) Inspect the light control ECU power source circuit.

Standard Resistance:

Click Location & Routing(A36) Click Connector(A36)

Tester Connection

Condition

Specified Condition

Result

A36-2 (B) - G-8

Always

Below 1 Ω

Ω

A36-5 (AS1) - G-19

Always

Below 1 Ω

Ω

A36-6 (LO) - G-11

Always

Below 1 Ω

Ω

If the result is not as specified, replace the headlight housing RH (headlight cord).

Adjustment

ADJUSTMENT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT

(a) Prepare the Toyota Prius vehicle:

  • Ensure that there is no damage or deformation to the vehicle body around the headlights.
  • Fill the fuel tank.
  • Make sure that the engine oil is filled to the specified level.
  • Make sure that the engine coolant is filled to the specified level.
  • Inflate the tires to the appropriate pressure.
  • Unload the trunk and Toyota Prius vehicle, ensuring that the spare tire, tools and jack are in their original positions.
  • Sit a person of average weight (68 kg, 150 lb) in the driver's seat.

2. PREPARE FOR HEADLIGHT AIMING (Using a headlight aim test machine)

(a) Adjust the headlight aim in accordance with the headlight aim test machine instructions.

3. PREPARE FOR HEADLIGHT AIMING (Using a screen)

(a) Prepare the Toyota Prius vehicle:

*a

Center Mark

  • Place the Toyota Prius vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
  • Place the vehicle at a 90° angle to the wall.
  • Create a 7.62 m (25 ft.) distance between the Toyota Prius vehicle (center marks of the headlights) and the wall.
  • Make sure that the vehicle is on a level surface.
  • Position the front wheels straight ahead.
  • Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 7.62 m (25 ft.) between the Toyota Prius vehicle (center marks of the headlights) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)

(b) Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.

(c) Draw a vertical line down the center of the screen (V line).

(d) Set the screen as shown in the illustration.

HINT:

  • Stand the screen perpendicular to the ground.
  • Align the V line on the screen with the center of the Toyota Prius vehicle.

(e) Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

  • The base lines differ for "low beam inspection" and "high beam inspection".
  • Mark the headlight center marks on the screen.

*a

Center Mark

*a

V LH Line

*b

V Line

*c

V RH Line

*d

H Line

*e

Ground

(1) H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the center marks of the headlights.

(2) V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center marks of the headlights).

4. INSPECT HEADLIGHT AIMING

(a) Cover the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

HINT:

When checking the aim of the high beam, cover the low beam.

(b) Start the engine.

(c) Turn on the headlights and check the aiming of each beam.

HINT:

  • Since the low beam headlight and the high beam headlight are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.
  • If the alignment distance is 7.62 m (25 ft.):

    The low beam cutoff line should be between 101 mm (3.97 in.) above or below the H line as well as 101 mm (3.97 in.) left or right of the V LH or RH line (SAE J599).

  • If the alignment distance is 3 m (9.84 ft.):

    The low beam cutoff line should be between 39 mm (1.56 in.) above or below the H line as well as 39 mm (1.56 in.) left or right of the V LH or RH line (SAE J599).

  • If the alignment distance is 7.62 m (25 ft.):

    The high beam center of intensity should be within 101 mm (3.97 in.) above or below the H line as well as 101 mm (3.97 in.) left and right of the V LH or RH line (SAE J599).

  • If the alignment distance is 3 m (9.84 ft.):

    The high beam center of intensity should be within 39 mm (1.56 in.) above or below the H line as well as 39 mm (1.56 in.) left or right of the V LH or RH line (SAE J599).

5. ADJUST HEADLIGHT AIMING

(a) Adjust the aim vertically:

(1) Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.

*a

Aiming Screw

-

-

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

HINT:

  • Since the low beam headlight and the high beam headlight are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.
  • If it is not possible to correctly adjust headlight aim, check the headlight unit and headlight unit lens installation.
  • Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.

Reassembly

REASSEMBLY

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
COMPONENTS (REASSEMBLY)

Procedure

Part Name Code

1

LIGHT CONTROL LED ECU

85967D

-

-

-

2

HEADLIGHT LEVELING MOTOR

85691

-

-

-

3

HEADLIGHT UNIT

81171A

-

-

4

INNER LENS ASSEMBLY

-

-

-

-

5

REFLECTOR

-

-

-

-

6

INNER LENS ASSEMBLY

-

-

-

-

7

HEADLIGHT LENS GASKET

81132B

-

-

8

HEADLIGHT LENS

81186

-

-

*1

HEADLIGHT LEVELING MOTOR WITH BRACKET

*2

HEADLIGHT LEVELING MOTOR BRACKET

●

Non-reusable part

-

-

Procedure

Part Name Code

9

FRONT SIDE RADAR SENSOR BRACKET

88215C

-

-

-

10

HEADLIGHT BRACKET

53246B

-

-

-

11

HEADLIGHT FRONT TURN SIGNAL LED

8113A

-

-

-

*A

w/ Front Turn Signal LED Socket

*B

w/ Front Side Radar

*1

HEADLIGHT UNIT SUB-ASSEMBLY

-

-

PROCEDURE

1. INSTALL LIGHT CONTROL LED ECU

2. INSTALL HEADLIGHT LEVELING MOTOR

3. INSTALL HEADLIGHT UNIT

NOTICE:

  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not allow dirt or foreign matter to get on the headlight unit or other components.
  • Prevention of static electricity is required during this procedure.
  • Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
  • Do not touch the headlight unit with bare hands.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

SST: 09890-47010

09891-04010

09891-04020

09891-04030

09891-04040

Adjustment Aiming Screws

Adjustment Aiming Rail

Install in this Direction

Turn in this Direction

(1) Install the pivot collar as shown in the illustration.

(2) Temporarily install the headlight unit assembly to the 2 adjustment aiming rails and 2 adjustment aiming screws as shown in the illustration.

(3) Hold the headlight unit assembly LH with one hand to prevent it from tipping over, alternately tighten the 2 adjustment aiming screws in the direction indicated by the arrow shown in the illustration, and align the dimensions with the recorded values at removal.

(1) Engage the 2 claws to connect the pivot collar.

(2) Connect the connector to install the headlight unit.

4. INSTALL INNER ASSEMBLY

5. INSTALL REFLECTOR

6. INSTALL INNER LENS ASSEMBLY

7. INSTALL HEADLIGHT LENS GASKET

NOTICE:

  • The headlight lens gasket must not be reused.
  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

*a

Release Paper

*b

Tape

*c

90°

-

-

Cleaning Area

-

-

(1) Clean the installation groove of the headlight lens.

(2) Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.

(3) Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.

(4) Using scissors, cut the end of the headlight lens gasket at a 90° angle.

Starting Position

-

-

(1) Starting from the position shown in the illustration and moving clockwise, temporarily install the headlight lens gasket as shown in the illustration.

NOTICE:

Gently install the headlight lens gasket without pulling it.

Straight Groove

Press in this Direction

Release Paper

-

-

(1) Repeat the following until the headlight lens gasket reaches the starting position.

1. Using 2 screwdrivers with their tips wrapped with release paper, completely press the headlight lens gasket into the straight groove to install it.

NOTICE:

  • Gently install the headlight lens gasket without pulling it.
  • If the headlight lens gasket is pulled while it is installed, it will not be installed properly.

2. Temporarily install the headlight lens gasket to the straight groove.

3. Temporarily install it to the corner groove.

NOTICE:

  • Gently install the headlight lens gasket without pulling it.
  • If the headlight lens gasket is pulled while it is installed, it will not be installed properly.

4. Completely press it into the groove.

Corner Groove

-

-

(1) Using scissors, cut the headlight lens gasket at a 45° angle at the starting position so that the headlight lens gasket overlaps itself 10 mm (0.394 in.) or more.

Standard Dimension:

Area

Dimension

-

-

A

10 mm (0.394 in.) or more

-

-

(2) Check the installation condition of the headlight lens gasket.

NOTICE:

  • Make sure the headlight lens gasket is not protruding and is installed properly.
  • Make sure there is no gap between the ends of the headlight lens gasket.
  • Make sure to thoroughly check the corners as the headlight lens gasket is likely to be improperly installed in the corners.

8. INSTALL HEADLIGHT LENS

NOTICE:

  • Make sure to wear clean rubber gloves when performing this procedure.
  • Do not allow dirt or foreign matter to get on the headlight lens.
  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
  • If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.
  • Do not use solvent to clean components. Only clean them with a dry cloth.

Cleaning Area

Headlight Lens Gasket

Headlight Lens

Headlight Housing

(1) Clean the sealing surface of the headlight lens.

(2) Temporarily install the headlight lens to the headlight housing.

NOTICE:

  • Temporarily install the headlight lens in the middle of the headlight lens gasket as shown in the illustration.
  • Check that the entire circumference of the headlight lens is positioned above the middle of the headlight lens gasket.

*a

"TORX" Screw

*b

Screw

(1) Engage the 8 claws in the order shown in the illustration to install the headlight lens.

NOTICE:

Make sure all of the claws are engaged.

(2) Install the 6 screws.

(3) Using a T20H "TORX" driver, install the "TORX" screw.

(4) Check the installation condition of the headlight lens gasket.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.

9. INSTALL FRONT SIDE RADAR SENSOR BRACKET (w/ Front Side Radar)

10. INSTALL HEADLIGHT BRACKET

11. INSTALL HEADLIGHT FRONT TURN SIGNAL LED (w/ Front Turn Signal LED Socket)

Installation

INSTALLATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
  • If the headlight assembly is damaged or deformed due to an accident, contact, etc., and repairs have been made to the area of the body to which the headlight assembly is installed, it is necessary to perform front side radar sensor adjustment.

    for Driving Adjustment: Click here

    for Target Adjustment (Triangle Target): Click here

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

HEADLIGHT ASSEMBLY

-

-

-

-

2

FRONT SIDE RADAR SENSOR

882B1

-

-

3

FRONT BUMPER ASSEMBLY

-

-

-

-

4

ADJUST HEADLIGHT AIMING

-

-

-

*A

w/ Front Side Radar

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

PROCEDURE

1. INSTALL HEADLIGHT ASSEMBLY

Torque:

Bolt :

7 N·m {71 kgf·cm, 62 in·lbf}

2. INSTALL FRONT SIDE RADAR SENSOR (w/ Front Side Radar)

Click here

3. INSTALL FRONT BUMPER ASSEMBLY

Click here

4. ADJUST HEADLIGHT AIMING

Click here