Digital Key Ecu
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during digital key ECU removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Digital Key ECU Assembly |
Code registration |
|
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Items for which learning is completed by driving the Toyota Prius vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more.

- Items for which learning is completed by operating the vehicle normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
for HEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
- After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.
-

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- |
- |
- |
- |
3 |
DECK BOARD ASSEMBLY |
58410B |
- |
- |
- |
4 |
DECK FLOOR BOX RH |
64995 |
- |
- |
- |
5 |
DECK FLOOR BOX LH |
64997 |
- |
- |
- |
6 |
REAR SEAT ASSEMBLY |
- |
- |
- |
- |
7 |
REAR DOOR SCUFF PLATE INSIDE RH |
67917F |
- |
- |
- |
8 |
REAR UNDER SIDE COVER RH |
76973E |
- |
- |
- |
9 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
62331A |
- |
- |
- |
10 |
LUGGAGE HOLD BELT STRIKER ASSEMBLY |
58460D |
- |
- |
|
11 |
REAR DECK TRIM COVER |
64716D |
- |
- |
- |
12 |
BATTERY SERVICE HOLE COVER ASSEMBLY |
58440 |
- |
- |
- |
13 |
REAR SEATBACK HINGE SUB-ASSEMBLY RH |
71303C |
- |
- |
- |
14 |
REAR SEAT SIDE GARNISH RH |
62551F |
- |
- |
|
15 |
LUGGAGE HOLD BELT STRIKER ASSEMBLY |
58460D |
- |
- |
- |
16 |
NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
81330 |
- |
- |
|
17 |
DECK TRIM SIDE PANEL ASSEMBLY RH |
64730B |
- |
- |
|
18 |
ROOF SIDE INNER GARNISH ASSEMBLY RH |
62470A |
- |
- |
- |
19 |
DIGITAL KEY ECU ASSEMBLY |
89000 |
- |
- |
|
*A |
w/ Spare Tire |
*B |
w/o Spare Tire |
*C |
for Type A |
*D |
for Type B |
*E |
for 2ZR-FXE |
*F |
for M20A-FXS |
*G |
for HEV Model |
- |
- |
*a |
HINT: As the illustration shown is an example, the actual details may differ. |
- |
- |
PROCEDURE
1. PRECAUTION
![]() |
NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
3. REMOVE DECK BOARD ASSEMBLY
Click here ![]()
4. REMOVE DECK FLOOR BOX RH
Click here ![]()
5. REMOVE DECK FLOOR BOX LH
Click here ![]()
6. REMOVE REAR SEAT ASSEMBLY
Click here ![]()
7. REMOVE REAR DOOR SCUFF PLATE INSIDE RH
Click here ![]()
8. REMOVE REAR UNDER SIDE COVER RH (for HEV Model)
Click here ![]()
9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here ![]()
10. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)
Click here ![]()
11. REMOVE REAR DECK TRIM COVER
Click here ![]()
12. REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)
Click here ![]()
13. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Click here ![]()
14. REMOVE REAR SEAT SIDE GARNISH RH
![]() |
Click here |
15. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
Click here ![]()
16. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
![]() |
Click here |
17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
![]() |
Click here |
18. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH
Click here ![]()
19. REMOVE DIGITAL KEY ECU ASSEMBLY
![]() |
NOTICE: Be careful when remove the digital key ECU assembly. If the digital key ECU assembly is dropped, replace it with a new one. |

Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
DIGITAL KEY ECU ASSEMBLY |
89000 |
- |
- |
|
2 |
ROOF SIDE INNER GARNISH ASSEMBLY RH |
62470A |
- |
- |
- |
3 |
DECK TRIM SIDE PANEL ASSEMBLY RH |
64730B |
- |
- |
- |
4 |
NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
81330 |
- |
- |
- |
5 |
LUGGAGE HOLD BELT STRIKER ASSEMBLY |
58460D |
- |
- |
- |
6 |
REAR SEAT SIDE GARNISH RH |
62551F |
- |
- |
|
7 |
REAR SEATBACK HINGE SUB-ASSEMBLY RH |
71303C |
- |
- |
- |
8 |
BATTERY SERVICE HOLE COVER ASSEMBLY |
58440 |
- |
- |
- |
9 |
REAR DECK TRIM COVER |
64716D |
- |
- |
- |
10 |
LUGGAGE HOLD BELT STRIKER ASSEMBLY |
58460D |
- |
- |
- |
11 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
62331A |
- |
- |
|
12 |
REAR UNDER SIDE COVER RH |
76973E |
- |
- |
- |
13 |
REAR DOOR SCUFF PLATE INSIDE RH |
67917F |
- |
- |
- |
14 |
REAR SEAT ASSEMBLY |
- |
- |
- |
|
15 |
DECK FLOOR BOX LH |
64997 |
- |
- |
- |
16 |
DECK FLOOR BOX RH |
64995 |
- |
- |
- |
17 |
DECK BOARD ASSEMBLY |
58410B |
- |
- |
- |
18 |
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- |
- |
- |
- |
19 |
REGISTRATION DIGITAL KEY ECU |
- |
- |
- |
|
20 |
INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL |
- |
- |
- |
|
*A |
w/ Spare Tire |
*B |
w/o Spare Tire |
*C |
for Type A |
*D |
for Type B |
*E |
for 2ZR-FXE |
*F |
for M20A-FXS |
*G |
for HEV Model |
- |
- |
*a |
HINT: As the illustration shown is an example, the actual details may differ. |
- |
- |
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
PROCEDURE
1. INSTALL DIGITAL KEY ECU ASSEMBLY
![]() |
NOTICE: Be careful when installing the digital key ECU assembly. If the digital key ECU assembly is dropped, replace it with a new one. |
Torque:
10 N·m {102 kgf·cm, 89 in·lbf}
2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH
3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
4. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
6. INSTALL REAR SEAT SIDE GARNISH RH
![]() |
Click here |
7. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
Torque:
18,1 N·m {185 kgf·cm, 13 ft·lbf}
8. INSTALL BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS)
9. INSTALL REAR DECK TRIM COVER
10. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)
11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
![]() |
Click here |
12. INSTALL REAR UNDER SIDE COVER RH (for HEV Model)
13. INSTALL REAR DOOR SCUFF PLATE INSIDE RH
14. INSTALL REAR SEAT ASSEMBLY
![]() |
Click here |
15. INSTALL DECK FLOOR BOX LH
16. INSTALL DECK FLOOR BOX RH
17. INSTALL DECK BOARD ASSEMBLY
18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
19. REGISTRATION DIGITAL KEY SYSTEM
Click here ![]()
20. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()




























