Front Side Radar Sensor

In this manual: Front Side Radar Sensor
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
21steps
~146min
5/5difficulty
4special tools
Done 0 of 21
  • Removal
  • Installation
  • Before Starting Driving Adjustment
  • Driving Adjustment
  • Ecu Data Save/write
  • Target Adjustment(triangle Target)
  • Check Reflection Power
  • On-vehicle Inspection

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front side radar sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Front bumper assembly*

Front television camera view adjustment

Panoramic View Monitor System

Advanced Park

Replacement or removal and installation of 2 or more parts:
  • Front television camera assembly, Radiator grille or Front bumper assembly
  • Rear television camera assembly
  • Side television camera assembly LH, Parking assist light LH or Outer rear view mirror assembly LH
  • Side television camera assembly RH, Parking assist light RH or Outer rear view mirror assembly RH

Television camera view adjustment

Panoramic View Monitor System

Front side radar sensor

ECU configuration

-

Adjust front side radar sensor

  • Front Camera System
  • Front Side Radar Sensor System

Triangle Target:

Driving Adjustment:

ECU DATA SAVE/WRITE:

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

FRONT SIDE RADAR ECU DATA SAVE

-

-

-

2

FRONT BUMPER ASSEMBLY

-

-

-

-

3

FRONT SIDE RADAR SENSOR

882B1

-

-

4

FRONT SIDE RADAR SENSOR BRACKET LH

88215C

-

-

-

5

FRONT SIDE RADAR SENSOR BRACKET RH

88215B

-

-

-

PROCEDURE

1. FRONT SIDE RADAR ECU DATA SAVE

Click here

2. REMOVE FRONT BUMPER ASSEMBLY

Click here

3. REMOVE FRONT SIDE RADAR SENSOR

NOTICE:

  • Do not drop the front side radar sensor.
  • If the front side radar sensor is dropped, replace it with a new one.

Remove in this Direction

-

-

(b) The orientation for the RH side is the opposite of the LH side.

4. REMOVE FRONT SIDE RADAR SENSOR BRACKET LH

HINT:

Perform this procedure only when replacement of the front side radar sensor bracket LH is necessary.

5. REMOVE FRONT SIDE RADAR SENSOR BRACKET RH

(a) Use the same procedure as for the LH side.

Installation

INSTALLATION

NOTICE:

  • Do not drop the front side radar sensor.
  • If the front side radar sensor is dropped, replace it with a new one.
  • After replacing the front side radar sensor, make sure to perform ECU configuration.

HINT:

  • The front side radar beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and to adjust the beam axis by using a reflector.
  • When checking the installation condition of the front side radar sensor, make sure it is between 26 and 34° with respect to the Toyota Prius vehicle center line. Also, using a tool, perform a check to make sure that the sensor is aligned perpendicular to the ground ( /- 2.2°).
COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

FRONT SIDE RADAR SENSOR BRACKET RH

88215B

-

-

-

2

FRONT SIDE RADAR SENSOR BRACKET LH

88215C

-

-

-

3

FRONT SIDE RADAR SENSOR

882B1

-

-

4

PERFORM FRONT SIDE RADAR SENSOR INSTALLATION CONDITION INSPECTION

-

-

-

5

FRONT BUMPER ASSEMBLY

-

-

-

-

6

ECU CONFIGURATION

-

-

-

7

FRONT SIDE RADAR ECU DATA WRITE

-

-

-

8

PERFORM FRONT SIDE RADAR BEAM AXIS CONFIRMATION

-

-

-

9

PERFORM DIAGNOSTIC SYSTEM CHECK

-

-

-

PROCEDURE

1. INSTALL FRONT SIDE RADAR SENSOR BRACKET RH

HINT:

Perform this procedure only when replacement of the front side radar sensor bracket RH is necessary.

2. INSTALL FRONT SIDE RADAR SENSOR BRACKET LH

3. INSTALL FRONT SIDE RADAR SENSOR

NOTICE:

  • Do not drop the front side radar sensor.
  • If the front side radar sensor is dropped, replace it with a new one.

4. PERFORM FRONT SIDE RADAR SENSOR INSTALLATION CONDITION INSPECTION

NOTICE:

After a minor collision has occurred or body repairs have been performed, etc., make sure to perform this inspection as there is a possibility that the installation angle has changed.

Click here

5. INSTALL FRONT BUMPER ASSEMBLY

Click here

6. ECU CONFIGURATION

Click here

7. FRONT SIDE RADAR ECU DATA WRITE

NOTICE:

Front side radar ECU data write can only be performed when the beam axis adjustment value is able to be saved to the GTS.

Click here

8. PERFORM FRONT SIDE RADAR BEAM AXIS CONFIRMATION

NOTICE:

When front side radar ECU data write can be performed, it is possible to omit the front side radar beam axis confirmation.

(a) When the front side radar sensor is replaced with a new one, adjustment of the front side radar beam axis must be performed.

HINT:

Front side radar sensor learning can be performed by using either Triangle Target or Driving Adjustment.

  • Target Adjustment (Triangle Target):

    Click here

  • Driving Adjustment:

    Click here

9. PERFORM DIAGNOSTIC SYSTEM CHECK

Before Starting Driving Adjustment

BEFORE STARTING DRIVING ADJUSTMENT

HINT:

  • Purpose of adjustment
    • When replacing the front side radar sensor, perform front side radar sensor beam axis learning to ensure proper operation of the system.
  • Beam Axis Direction

    *a

    Beam Axis Direction

PROCEDURE

1. PERFORM DRIVING ADJUSTMENT

NOTICE:

  • When performing the driving adjustment, obey all applicable traffic laws.
  • Select a road where the driving adjustment can be carried out safely.
  • Do not install anything other than a genuine bumper assembly.
  • If the front bumper cover has been replaced or body repair has been performed at a radio wave transmission area, "driving adjustment" cannot be performed.

    *a

    Bumper Rear Side

    *b

    Scribed Line

    Radio Wave Transmission Area

    -

    -

    *a

    282 mm (11.10 in.)

    *b

    48 mm (1.89 in.)

    *c

    122 mm (4.80 in.)

    *d

    224 mm (8.82 in.)

    *e

    79 mm (3.11 in.)

    *f

    291 mm (11.46 in.)

    *g

    122 mm (4.80 in.)

    *h

    156 mm (6.14 in.)

    *j

    146 mm (5.75 in.)

    *k

    206 mm (8.11 in.)

    Radio Wave Transmission Area

    -

    -

  • If body repairs have been performed, perform "Check Reflection Power".

    Click here

(a) Driving adjustment concept

  • The front side radar sensor emits radio waves in the millimeter wave band, and if objects that reflect these radio waves are present within the detection range, the system uses those reflected waves to detect the distance to, direction of, and relative speed of those objects.
  • On curves, the estimated curve radius is used to perform course compensation.
  • The time required before adjustment is completed varies according to the Toyota Prius vehicle speed and external conditions.

*A

Forward View

*a

Movement in external environment

(b) Driving conditions

  • Drive the Toyota Prius vehicle straight ahead at a speed of 10 km/h or more.
  • Perform the adjustment outside during daytime, on a sunny or cloudy day.
  • If preceding vehicles are present, they should be kept at a distance of at least 20 m (66 ft.)
  • There is a stationary object on the roadside such as a guardrail.
  • Ensure that there is no snow, ice, or foreign matter on the front or rear of the radar sensor cover or on the front surface of the sensor.

NOTICE:

If the sensor axis is excessively misaligned, the online axis alignment may not be able to make progress.

The total cumulative time that is required for the adjustment to complete when the Toyota Prius vehicle is driven with all conditions met is approximately 5 to 15 minutes.

HINT:

  • If the adjustment does not complete within a total cumulative time of 15 minutes when the vehicle is driven with all conditions met, perform the adjustment on another route.
  • If the adjustment does not complete within a total cumulative time of 30 minutes when the Toyota Prius vehicle is driven with all conditions met, perform the adjustment using target recognition.
  • If the vehicle is driven unsteadily or many lane changes are performed, the time taken for adjustment to complete may increase.

(c) Road environment

HINT:

When driving on a bumpy or unpaved road, making frequent accelerations and decelerations, etc., the front side radar sensor condition may be unstable, which may cause adjustment to take a long time.

  • Road environments conducive to adjustment

    *a

    Roads with stationary metallic objects such as guard rails

  • Road environments which hinder adjustment

    *a

    Inside tunnels where there are many diffuse radar reflections

    *b

    Underneath elevated structures where there are many diffuse radar reflections

    *c

    In residential neighborhoods where there are many diffuse radar reflections

    *d

    Snowy roads, dirt roads, etc., where there are very few radar reflections

Driving Adjustment

DRIVING ADJUSTMENT

NOTICE:

  • Make sure to read "Before Starting Driving Adjustment" before proceeding with work.

    Click here

  • Make sure that the alignment is suitable and non-standard tires are not installed.
  • Make sure to perform the transition to online axis alignment mode with the Toyota Prius vehicle stopped.
  • Transitioning to online axis alignment mode will erase the learning value, so make sure to complete the adjustment.
  • Turning the ignition switch off while in online axis alignment mode will cause the system to exit online axis alignment mode, so to continue with the adjustment, it is necessary to transition to online axis alignment mode again.
  • All of the driving support system functions will be inoperative while the adjustment is in progress.
  • When driving the Toyota Prius vehicle with the GTS connected, be careful with how the wires are routed.
  • If the adjustment does not complete within a total cumulative time of 15 minutes when the vehicle is driven with all conditions met, perform the adjustment on another route.
  • If the adjustment does not complete within a total cumulative time of 30 minutes when the Toyota Prius vehicle is driven with all conditions met, perform the adjustment using target recognition.
  • After adjustment is complete, to start the various systems it is necessary to turn the ignition switch off and then to ON again.
  • In situations such as when the online axis alignment terminates abnormally, to perform online axis alignment again, turn the ignition switch off and then back to ON and enter online axis alignment mode again.
  • If the front bumper cover has been replaced or body repair has been performed at a radio wave transmission area, "driving adjustment" cannot be performed.
  • If body repairs have been performed, perform "Check Reflection Power".

    Click here

PROCEDURE

1. PERFORM FRONT SIDE RADAR SENSOR BEAM AXIS LEARNING

(a) Adjust the tire pressures to the standard values.

Click here

(b) Check that the surface and back of the front bumper cover and the surface of the front side radar sensors are clean and free of foreign matter such as dirt and snow. If foreign matter such as dirt and snow is found, remove it.

(c) Check that the front bumper assembly, headlight assembly and front side radar sensor bracket are securely installed, and that there is no damage or deformation around the installation areas. If any abnormalities are found, repair or replace parts as necessary.

(d) Perform Transition to Online Axis Alignment Mode.

(1) With the ignition switch off, connect the GTS to the DLC3.

(2) Turn the ignition switch to ON.

(3) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility / Transition to Online Axis Alignment Mode.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

for Type A:

Body Electrical > Front Side Radar "A" > Utility

Transition to Online Axis Alignment Mode

Body Electrical > Front Side Radar "B" > Utility

Transition to Online Axis Alignment Mode

for Type B:

Body Electrical > Front Side Radar "A" > Utility

Transition to Online Axis Alignment Mode

Body Electrical > Front Side Radar "B" > Utility

Transition to Online Axis Alignment Mode

(4) Confirm the conditions displayed on the screen and then press "Next".

(5) Select "Front Side Radar "A"" or "Front Side Radar "B"" and then press "Next".

(6) Check the GTS screen and confirm that it has transitioned to online axis alignment mode.

(7) Press "Next".

(8) When driving with GTS not connected to Toyota Prius vehicle:

  1. In accordance with the instructions on the screen press "Exit" and then disconnect the GTS from the DLC3.

(e) Online axis adjustment (Beam Axis Learning)

(1) Drive the vehicle to perform beam axis learning.

HINT:

If the alignment is performed with the GTS connected to the Toyota Prius vehicle, the alignment progress can be monitored through 5 stages on the GTS screen.

(2) If the online axis alignment completes normally, the buzzer will sound intermittently for 1.5 seconds.

NOTICE:

  • In the case of abnormal termination, the buzzer sounds intermittently for 1 second.
  • When driving with GTS connected to Toyota Prius vehicle:
    • If an error code is displayed, perform troubleshooting according to the following table, then perform the beam axis alignment again.
  • When driving with GTS not connected to vehicle:
    • When the system terminates abnormally, connect the GTS and refer to the following error code table, then perform beam axis alignment again.

      Click here

Error No.

Error Description

Cause of Error

Action to be Taken

2

Target angle abnormality

  • The beam axis of the front side radar sensor is outside the automatic correction range.

Check the condition of the front side radar sensor, front side radar sensor bracket, headlight assembly and front bumper assembly.

3

Radar abnormality

  • Operation of the front side radar sensor is abnormal.

Replace the front side radar sensor.

4

Temperature abnormality

  • The temperature around the front side radar sensor is too high.

Wait until the temperature drops to the operable range (-40 to 85 °C).

5

Voltage abnormality

  • IG power source voltage is outside the operable range of the front side radar sensor.

Check the auxiliary battery voltage (specified condition: 7.5 to 16 V).

  • for M20A-FXS:

    Click here

  • for 2ZR-FXE:

    Click here

6

Toyota Prius Vehicle information undefined

  • There is a front side radar sensor communication error (CAN communication error between the front side radar sensors).

Check that the connectors of the front side radar sensor and the junction block are firmly connected.

7

Toyota Prius Vehicle speed abnormality

  • The vehicle is moving.

Ensure that the vehicle remains stationary.

8

Time out

  • The Toyota Prius vehicle cannot communicate with GTS normally.
  • Operation of the front side radar sensor is abnormal.
  • Ensure that the vehicle is connected with the GTS correctly.
  • Perform online axis adjustment again and replace the front side radar sensor if the same error code is output.

(3) When driving with GTS connected to Toyota Prius vehicle:

  1. Press "Exit" to exit the Online axis adjustment mode.

(4) Turn the ignition switch off.

(5) When driving with GTS not connected to vehicle:

  1. Connect the GTS to the DLC3.

(6) Turn the ignition switch to ON and check that the warning light turns off.

(7) Check that the value of Data List item "Beam Axis Adjustment Completion Status" is "Completed".

HINT:

  • If the value of "Beam Axis Adjustment Completion Status" is "Incompleted", perform "Online Axis Alignment Mode" again.
  • The "A" is on the LH side and the "B" is on the RH side.
Body Electrical > Front Side Radar "A" > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Beam Axis Adjustment Completion Status

Displays the status of beam axis alignment completion

Incompleted or Completed

Incompleted: Beam axis alignment not completed

Completed: Beam axis alignment completed

-

Body Electrical > Front Side Radar "A" > Data List

Beam Axis Adjustment Completion Status

Body Electrical > Front Side Radar "B" > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Beam Axis Adjustment Completion Status

Displays the status of beam axis alignment completion

Incompleted or Completed

Incompleted: Beam axis alignment not completed

Completed: Beam axis alignment completed

-

Body Electrical > Front Side Radar "B" > Data List

Beam Axis Adjustment Completion Status

Standard:

The value of the Data List item is displayed as "Completed".

(8) In accordance with the instructions on the screen press "Exit".

(9) Turn the ignition switch off.

(10) Disconnect the GTS from the DLC3.

(f) Front side radar sensor beam axis learning is complete.

(g) After beam axis adjustment completes, clear the following system Toyota Prius vehicle control history entries.

(1) Clear vehicle control history (Front Side Radar Sensor System).

Click here

Ecu Data Save/write

ECU DATA SAVE/WRITE

PROCEDURE

1. FRONT SIDE RADAR ECU DATA SAVE

NOTICE:

In the following situations, perform "Front Side Radar Beam Axis Confirmation" or "Check Reflection Power" after replacing the front side radar sensor with a new one as the values of the beam axis alignment cannot be stored by the GTS.

  • When a minor collision is suspected.
  • When body repairs have been performed on the Toyota Prius vehicle.
  • For a vehicle in which the system frequently operates inappropriately or fails to operate.
  • When a DTC for front side radar sensor (module "A") beam axis misalignment (horizontal) or front side radar sensor (module "B") beam axis misalignment (horizontal) has been stored.
  • When Toyota Prius vehicle control history (RoB) code for front side radar sensor (module "A") blockage or front side radar sensor (module "B") blockage has been stored.
  • When vehicle control history (RoB) code for front side radar sensor (module "A") blockage Level 2 or front side radar sensor (module "B") blockage Level 2 has been stored.
  • If body repair has been performed at a radio wave transmission area of the front bumper cover, make sure to perform "Check Reflection Power".

    Click here

    *a

    Bumper Rear Side

    *b

    Scribed Line

    Radio Wave Transmission Area

    -

    -

    *a

    282 mm (11.10 in.)

    *b

    48 mm (1.89 in.)

    *c

    122 mm (4.80 in.)

    *d

    224 mm (8.82 in.)

    *e

    79 mm (3.11 in.)

    *f

    291 mm (11.46 in.)

    *g

    122 mm (4.80 in.)

    *h

    156 mm (6.14 in.)

    *j

    146 mm (5.75 in.)

    *k

    206 mm (8.11 in.)

    Radio Wave Transmission Area

    -

    -

HINT:

By performing front side radar "A" ECU data save or front side radar "B" ECU data save, it becomes possible to save the beam axis adjustment value to the GTS.

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" ECU Data Save

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" ECU Data Save

(e) Check the results displayed for the front side radar "A" ECU data save or front side radar "B" ECU data save.

2. FRONT SIDE RADAR ECU DATA WRITE

NOTICE:

  • Before replacing the front side radar sensor LH, read the values and then write them to the new front side radar sensor LH.
  • Before replacing the front side radar sensor RH, read the values and then write them to the new front side radar sensor RH.

HINT:

By performing front side radar "A" ECU data write or front side radar "B" ECU data write, the beam axis adjustment value from the old front side radar sensor before replacement can be written to the new front side radar sensor.

(a) Turn the ignition switch off.

(b) Connect the GTS to the DLC3.

(c) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" ECU Data Write

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" ECU Data Write

(e) Check the results displayed for the front side radar "A" ECU data write or front side radar "B" ECU data write.

Target Adjustment(triangle Target)

TARGET ADJUSTMENT(TRIANGLE TARGET)

PROCEDURE

1. PERFORM FRONT SIDE RADAR BEAM AXIS CONFIRMATION

NOTICE:

If body repair has been performed at a radio wave transmission area of the front bumper cover, make sure to perform "Check Reflection Power".

Click here

*a

Bumper Rear Side

*b

Scribed Line

Radio Wave Transmission Area

-

-

*a

282 mm (11.10 in.)

*b

48 mm (1.89 in.)

*c

122 mm (4.80 in.)

*d

224 mm (8.82 in.)

*e

79 mm (3.11 in.)

*f

291 mm (11.46 in.)

*g

122 mm (4.80 in.)

*h

156 mm (6.14 in.)

*j

146 mm (5.75 in.)

*k

206 mm (8.11 in.)

Radio Wave Transmission Area

-

-

HINT:

  • The front side radar beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and to adjust the beam axis by using a reflector.
  • If body repairs have not been performed at a radio wave transmission area of the front bumper cover, select a target distance of 2500 mm (8.2 ft.) when performing front side radar beam axis confirmation.

(a) When performing the front side radar beam axis confirmation, move the Toyota Prius vehicle to a place where the space shown in the illustration can be secured.

*A

Right Side of Toyota Prius Vehicle

*B

Left Side of Vehicle

*a

Vehicle Center Line

*b

Front Bumper

*c

Inspection Area

-

-

Standard:

Location

Measurement

a

2 m (6.56 ft.)

b

4 m (13.12 ft.)

c

6 m (19.68 ft.)

NOTICE:

  • Perform this inspection on level ground.
  • Make sure that there are no metal objects around the Toyota Prius vehicle or on the ground.
  • Unload the vehicle before beginning the inspection.
  • Confirm that the tire pressure is correct before beginning the inspection.

    Click here

  • Do not place any objects other than the reflector (such as a large metallic object) in the inspection area or allow people to enter the inspection area (W 6 m [19.68 ft.] x L 6 m [19.68 ft.] x H 3 m [9.84 ft.]) shown in the illustration.

(b) Place the reflector.

(1) Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the Toyota Prius vehicle (point A) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(2) Hang a weight with a pointed tip from the center of the radiator grille (or front panel) emblem, and mark the front center point of the Toyota Prius vehicle (point B) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(3) When using a laser line marker:

NOTICE:

Do not look directly into the laser beam.

  1. Press the laser mode button on the laser line marker to activate the laser line emitters.
  2. Align the laser beam ground marking point (cross portion) with point B.

    *a

    Ground Marking Point (Cross Portion)

  3. Align the center of the target panel with point A, and set the target panel so that it faces forward.

    *a

    Center Line

    *b

    Target Panel

  4. Adjust the position of the laser line marker so that the laser beam is aligned with the center line of the target panel.
  5. Using a laser marker, create a Toyota Prius vehicle center line that connects point A and point B.

    *a

    Vehicle Center Line

(4) When not using a laser line marker:

  1. Draw a Toyota Prius vehicle center line so that it passes through mark A and B (front and rear center points).

    *a

    Toyota Prius Vehicle Center Line

(5) Enlarge and print out the poster shown in the illustration.

*a

Poster

*b

Edge of Front Bumper

*c

Line C

*d

Toyota Prius Vehicle Center Line

Standard:

Part

Angle

a

74°

(6) Attach the printed poster to the floor with the Toyota Prius vehicle center line aligned with point B as shown in the illustration.

*a

Poster

*b

Toyota Prius Vehicle Center Line

(7) Align a piece of string with line C and mark point D at a distance of 3088 mm (10.13 ft.) from point B.

*a

Toyota Prius Vehicle Front

*b

Vehicle Center Line

*c

String

*d

Poster

(8) Set the reflector at the point D shown in the illustration below.

SST: 09870-60000

09870-60010

SST: 09870-60040

*A

Right Side of Toyota Prius Vehicle

*B

Left Side of Vehicle

*a

Vehicle Center Line

*b

Reflector

Standard:

Part

Length

a

3088 mm (10.13 ft.)

NOTICE:

  • Set the reflector so that its center is 551 mm (1.81 ft.) above the ground.

    *a

    SST (reflector)

    *b

    551 mm (1.81 ft.)

  • The center of the triangular pyramid is the reference point for the setting position and angle.

    *a

    Center of Triangular Pyramid

    *a

    SST (reflector)

(c) Perform the front side radar beam axis display.

(1) Turn the ignition switch off.

(2) Connect the GTS to the DLC3.

(3) Turn the ignition switch ON and turn the front side radar system on.

(4) Turn the GTS on.

(5) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility / Front Side Radar "A" Beam Axis Display or Front Side Radar "B" Beam Axis Display.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" Beam Axis Display

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" Beam Axis Display

(6) Confirm the conditions displayed on the screen, and then press "Next".

(7) Select "2500 mm (8.2 ft.)" as the target distance and then press "Next".

(8) Perform the procedure in accordance with the instructions on the screen.

(9) Check the results displayed for the front side radar beam axis display.

Allowable Range:

Item

Front Side Radar Sensor ("A")

Front Side Radar Sensor ("B")

Angle

-4.1 to 4.1°

-4.1 to 4.1°

HINT:

If the displayed results are outside the permissible range, the following are possible causes. Therefore, implement countermeasures, check the front side radar beam axis and perform the procedure again.

Possible Causes

Countermeasure

Incorrect SST (reflector) position

Check the position of SST (reflector) and checking space and perform the procedure again

A metallic object is located in the vicinity of the checking space

Check the position of SST (reflector) and checking space and perform the procedure again

The front side radar sensor installation is abnormal

Check the installation condition of the front side radar sensor

Click here

(10) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility / Front Side Radar "A" Beam Axis Adjustment or Front Side Radar "B" Beam Axis Adjustment.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" Beam Axis Adjustment

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" Beam Axis Adjustment

(11) Confirm the conditions displayed on the screen, and then press "Next".

(12) Select "2500 mm (8.2 ft.)" as the target distance and then press "Next".

(13) In accordance with the screen, perform Front Side Radar "A" Beam Axis Adjustment' or Front Side Radar "B" Beam Axis Adjustment'.

HINT:

  • If the result of the front side radar beam axis display is within the specified range, then this adjustment has corrected the value to normal.
  • "Reflector Reflection Power" is displayed after completing the front side radar beam axis adjustment, but is unnecessary if body repairs have not been performed at the radio wave transmission area of the front bumper cover.

(d) After the beam axis adjustment is completed, check the "Radio Wave Irradiation Condition" of the millimeter wave radar sensor assembly.

HINT:

When performing the beam axis alignment, temporarily disable operation of the millimeter wave radar sensor assembly to prevent exposure to radio waves from the millimeter wave radar sensor assembly. For this reason, it is necessary to check that the millimeter wave radar sensor assembly is operational after completing beam axis alignment.

(1) Enter the following menus: Body Electrical / Front Radar Sensor / Data List / Radio Wave Irradiation Condition.

Body Electrical > Front Radar Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Radio Wave Irradiation Condition

Status of radio wave irradiation

Under Radio Wave Irradiation or Under Radio Wave Stopping

Under Radio Wave Irradiation: Radio wave irradiation status displayed

Under Radio Wave Stopping: Radio wave irradiation stopped status displayed

-

Body Electrical > Front Radar Sensor > Data List

Radio Wave Irradiation Condition

Standard:

The value of the Data List item is displayed as "Under Radio Wave Irradiation".

(2) When the value is "Under Radio Wave Stopping":

  1. Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Radio Wave Irradiation Stop Mode Cancellation.
Body Electrical > Front Radar Sensor > Utility

Radio Wave Irradiation Stop Mode Cancellation

(e) After beam axis adjustment completes, clear the following system Toyota Prius vehicle control history entries.

(1) Clear vehicle control history (Front Side Radar Sensor System).

Click here

(2) Clear vehicle control history (Front Camera System).

Click here

Check Reflection Power

CHECK REFLECTION POWER

PROCEDURE

1. CHECK FRONT SIDE RADAR SENSOR REFLECTION POWER

NOTICE:

  • If body repairs have been performed at the radio wave transmission area of the front bumper cover, select a target distance of 2500 mm (8.2 ft.) and be sure to perform "Check Reflection Power".

    *a

    Bumper Rear Side

    *b

    Scribed Line

    Radio Wave Transmission Area

    -

    -

    *a

    282 mm (11.10 in.)

    *b

    48 mm (1.89 in.)

    *c

    122 mm (4.80 in.)

    *d

    224 mm (8.82 in.)

    *e

    79 mm (3.11 in.)

    *f

    291 mm (11.46 in.)

    *g

    122 mm (4.80 in.)

    *h

    156 mm (6.14 in.)

    *j

    146 mm (5.75 in.)

    *k

    206 mm (8.11 in.)

    Radio Wave Transmission Area

    -

    -

  • "Check Reflection Power" enables the reflection power to be checked after beam axis alignment in accordance with the following procedure.

HINT:

  • Since radio waves from the front side radar sensor pass through the front bumper cover, if body repairs have been performed at the radio wave transmission area, radio wave transmission may be attenuated.
  • Perform "Check Reflection Power" with and without the front bumper assembly installed to check the difference.

(a) When performing the front side radar beam axis confirmation, move the Toyota Prius vehicle to a place where the space shown in the illustration can be secured.

*A

Right Side of Toyota Prius Vehicle

*B

Left Side of Vehicle

*a

Vehicle Center Line

*b

Front Bumper

*c

Inspection Area

-

-

Standard:

Location

Measurement

a

2 m (6.56 ft.)

b

4 m (13.12 ft.)

c

6 m (19.68 ft.)

NOTICE:

  • Perform this inspection on level ground.
  • Make sure that there are no metal objects around the Toyota Prius vehicle or on the ground.
  • Unload the vehicle before beginning the inspection.
  • Confirm that the tire pressure is correct before beginning the inspection.

    Click here

  • Do not place any objects other than the reflector (such as a large metallic object) in the inspection area or allow people to enter the inspection area (W 6 m [19.68 ft.] x L 6 m [19.68 ft.] x H 3 m [9.84 ft.]) shown in the illustration.

(b) Place the reflector.

(1) Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the Toyota Prius vehicle (point A) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(2) Hang a weight with a pointed tip from the center of the radiator grille (or front panel) emblem, and mark the front center point of the Toyota Prius vehicle (point B) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(3) When using a laser line marker:

NOTICE:

Do not look directly into the laser beam.

  1. Press the laser mode button on the laser line marker to activate the laser line emitters.
  2. Align the laser beam ground marking point (cross portion) with point B.

    *a

    Ground Marking Point (Cross Portion)

  3. Align the center of the target panel with point A, and set the target panel so that it faces forward.

    *a

    Center Line

    *b

    Target Panel

  4. Adjust the position of the laser line marker so that the laser beam is aligned with the center line of the target panel.
  5. Using a laser marker, create a Toyota Prius vehicle center line that connects point A and point B.

    *a

    Vehicle Center Line

(4) When not using a laser line marker:

  1. Draw a Toyota Prius vehicle center line so that it passes through mark A and B (front and rear center points).

    *a

    Toyota Prius Vehicle Center Line

(5) Enlarge and print out the poster shown in the illustration.

*a

Poster

*b

Edge of Front Bumper

*c

Line C

*d

Toyota Prius Vehicle Center Line

Standard:

Part

Angle

a

74°

(6) Attach the printed poster to the floor with the Toyota Prius vehicle center line aligned with point B as shown in the illustration.

*a

Poster

*b

Toyota Prius Vehicle Center Line

(7) Align a piece of string with line C and mark point D at a distance of 3088 mm (10.13 ft.) from point B.

*a

Toyota Prius Vehicle Front

*b

Vehicle Center Line

*c

String

*d

Poster

(8) Set the reflector at the point D shown in the illustration below.

SST: 09870-60000

09870-60010

SST: 09870-60040

*A

Right Side of Toyota Prius Vehicle

*B

Left Side of Vehicle

*a

Vehicle Center Line

*b

Reflector

Standard:

Part

Length

a

3088 mm (10.13 ft.)

NOTICE:

  • Set the reflector so that its center is 551 mm (1.81 ft.) above the ground.

    *a

    SST (reflector)

    *b

    551 mm (1.81 ft.)

  • The center of the triangular pyramid is the reference point for the setting position and angle.

    *a

    Center of Triangular Pyramid

    *a

    SST (reflector)

(c) Check reflection power.

(1) Turn the ignition switch off.

(2) Connect the GTS to the DLC3.

(3) Turn the ignition switch ON and turn the front side radar system on.

(4) Turn the GTS on.

(5) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility / Front Side Radar "A" Beam Axis Display or Front Side Radar "B" Beam Axis Display.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" Beam Axis Display

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" Beam Axis Display

(6) Confirm the conditions displayed on the screen, and then press "Next" (*1).

(7) Select "2500 mm (8.2 ft.)" as the target distance and then press "Next".

(8) Perform the procedure in accordance with the instructions on the screen.

(9) Check the results displayed for the front side radar beam axis display.

Allowable Range

Item

Front Side Radar Sensor ("A")

Front Side Radar Sensor ("B")

Angle

-4.1 to 4.1°

-4.1 to 4.1°

HINT:

If the displayed results are outside the permissible range, the following are possible causes. Therefore, implement countermeasures, check the front side radar beam axis and perform the procedure again.

Possible Causes

Countermeasure

Incorrect SST (reflector) position

Check the position of SST (reflector) and checking space and perform the procedure again

A metallic object is located in the vicinity of the checking space

Check the position of SST (reflector) and checking space and perform the procedure again

The front side radar sensor installation is abnormal

Check the installation condition of the front side radar sensor

Click here

(10) Enter the following menus: Body Electrical / Front Side Radar "A" or Front Side Radar "B" / Utility / Front Side Radar "A" Beam Axis Adjustment or Front Side Radar "B" Beam Axis Adjustment.

HINT:

The "A" is on the LH side and the "B" is on the RH side.

Body Electrical > Front Side Radar "A" > Utility

Front Side Radar "A" Beam Axis Adjustment

Body Electrical > Front Side Radar "B" > Utility

Front Side Radar "B" Beam Axis Adjustment

(11) Confirm the conditions displayed on the screen, and then press "Next".

(12) Select "2500 mm (8.2 ft.)" as the target distance and then press "Next".

(13) In accordance with the screen, perform Front Side Radar "A" Beam Axis Adjustment or Front Side Radar "B" Beam Axis Adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.

(14) After front side radar beam axis adjustment is complete, note the value of "Reflector Reflection Power".

HINT:

  • Do not move the reflector after removing the front bumper assembly, so that the process can be started again from "Front Side Radar Beam Axis Display" (*1).
  • If the reflector is moved, variations in the measured values occur and the results cannot be accurately compared.

(15) Remove the front bumper assembly.

Click here

(16) Perform the procedure again from "Front Side Radar Beam Axis Display" (*1) and note the value of "Reflector Reflection Power".

(17) Check the difference in value of "Reflector Reflection Power" with and without the front bumper assembly installed and confirm that the result is as specified.

HINT:

  • Subtract the value with the front bumper assembly removed from the value with the front bumper assembly installed, and then check the result.
  • If different reflectors are used with the front bumper assembly installed and removed, the measured values will vary and the correct difference cannot be determined.

(18) Calculate the difference in reflection power.

HINT:

Formula: front bumper assembly installed - front bumper assembly removed

Standard:

Item

Standard

Front Side Radar Sensor ("A")

-5.0 or higher

Front Side Radar Sensor ("B")

-5.0 or higher

HINT:

If the calculated value is -5.0 or higher, there is no problem.

*a

Calculated Value

-

-

Outside Specified Range

Within Specified Range

(19) If the difference in "Reflector Reflection Power" is outside of the specified range:

  1. Suspect the following possible causes and perform the appropriate countermeasures:

    Possible Causes

    Countermeasure

    • When the front bumper cover panel was painted, too much paint base was applied.
    • Excessive addition of aluminum primary color

    Strip the front bumper cover back to its base material, and then repaint.

    Operation of the front side radar sensor is abnormal.

    Replace the front side radar sensor.

    HINT:

    If the result is outside of the specified range, it is suspected that body repair performed on the front bumper cover is reducing the reflection power.

  2. After performing the appropriate countermeasures above, perform the operation again from "Front Side Radar Beam Axis Display"(*1) and confirm that "Reflector Reflection Power" is within the acceptable range.

    HINT:

    Refer to the body repair manual "INTRODUCTION > WORK NOTICES AND PRECAUTIONS > PRECAUTIONS FOR FRONT SIDE RADAR SENSOR".

(20) Install the front bumper assembly.

Click here

(d) After "Check Reflection Power" is completed, check "Radio Wave Irradiation Condition" of the millimeter wave radar sensor assembly.

HINT:

When performing the beam axis alignment, temporarily disable operation of the millimeter wave radar sensor assembly to prevent exposure to radio waves from the millimeter wave radar sensor assembly.

(1) Enter the following menus: Body Electrical / Front Radar Sensor / Data List / Radio Wave Irradiation Condition.

Body Electrical > Front Radar Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Radio Wave Irradiation Condition

Status of radio wave irradiation

Under Radio Wave Irradiation or Under Radio Wave Stopping

Under Radio Wave Irradiation: Radio wave irradiation status displayed

Under Radio Wave Stopping: Radio wave irradiation stopped status displayed

-

Body Electrical > Front Radar Sensor > Data List

Radio Wave Irradiation Condition

Standard:

The value of the Data List item is displayed as "Under Radio Wave Irradiation".

(2) When the value is "Under Radio Wave Stopping":

  1. Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Radio Wave Irradiation Stop Mode Cancellation.
Body Electrical > Front Radar Sensor > Utility

Radio Wave Irradiation Stop Mode Cancellation

(e) After beam axis adjustment completes, clear the following system Toyota Prius vehicle control history entries.

(1) Clear vehicle control history (Front Side Radar Sensor System).

Click here

(2) Clear vehicle control history (Front Camera System).

Click here

On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. PERFORM FRONT SIDE RADAR SENSOR INSTALLATION CONDITION INSPECTION

NOTICE:

  • After a minor collision has occurred or body repairs have been performed, etc., make sure to perform this inspection as there is a possibility that the installation angle has changed.
  • Perform this inspection on level ground.
  • Unload the Toyota Prius vehicle before beginning the inspection.
  • Confirm that the tire pressure is correct before beginning the inspection.

    Click here

HINT:

When checking the installation condition of the front side radar sensor, make sure it is between 26 and 34° with respect to the Toyota Prius vehicle center line. Also, using a tool, perform a check to make sure that the sensor is aligned perpendicular to the ground ( /- 2.2°).

(a) Horizontal mounting angle check

(1) Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(2) Hang a weight with a pointed tip from the center of the radiator grille (or front panel) emblem, and mark the front center point of the Toyota Prius vehicle (point B) on the ground.

*a

String

*b

Weight

*c

Center

-

-

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.

(3) When using a laser line marker:

NOTICE:

Do not look directly into the laser beam.

  1. Press the laser mode button on the laser line marker to activate the laser line emitters.
  2. Align the laser beam ground marking point (cross portion) with point B.

    *a

    Ground Marking Point (Cross Portion)

  3. Align the center of the target panel with point A, and set the target panel so that it faces forward.

    *a

    Center Line

    *b

    Target Panel

  4. Adjust the position of the laser line marker so that the laser beam is aligned with the center line of the target panel.
  5. Using a laser marker, create a Toyota Prius vehicle center line that connects point A and point B.

    *a

    Vehicle Center Line

(4) When not using a laser line marker:

  1. Draw a Toyota Prius vehicle center line so that it passes through mark A and B (front and rear center points).

    *a

    Toyota Prius Vehicle Center Line

(5) Remove the front bumper assembly.

Click here

(6) Attach double-sided tape to the digital angle gauge attachment A as shown in the illustration.

SST: 09989-00010

*a

SST (Digital Angle Gauge Attachment A)

Double-sided Tape

HINT:

  • Make sure to use double-sided tape with the same thickness for both the left and right sides.
  • If the thickness of the double-sided tape is different for the left and right sides, an accurate measurement cannot be performed.

(7) Remove the release paper from the double-sided tape, and attach the digital angle gauge attachment A to the front side radar sensor.

*a

SST (Digital Angle Gauge Attachment A)

(8) Mark points C and D on the ground by hanging a pointed weight from two points at the side part of the convex surface of the radome, as shown in the illustration.

*1

Front Side Radar Sensor

-

-

*a

String

*b

Weight

*c

Side Part of Convex Surface of Radome

*d

SST (Digital Angle Gauge Attachment A)

Standard:

Location

Measurement

a

55 mm (2.17 in.)

HINT:

Make sure the string hangs straight down so that it does not contact parts of the Toyota Prius vehicle.

(9) When using a laser line marker:

NOTICE:

Do not look directly into the laser beam.

  1. Press the laser mode button on the laser line marker to activate the laser line emitters.
  2. Adjust the position of the laser line marker so that the laser beam passes through point C and point D as shown in the illustration.

    *a

    Ground Marking Point (Cross Portion)

  3. Enlarge and print out the poster shown in the illustration.

    *a

    Poster

    *b

    Toyota Prius Vehicle

    *c

    Vehicle Center Line

    *d

    Intersection of Vehicle Center Line and extension lines of Point C and Point D

    Allowable Range

    -

    -

    Standard:

    Part

    Angle

    a

    30°

    b

    -4°

    c

    4°

  4. As shown in the illustration, attach the poster to the ground by aligning the center line of the Toyota Prius vehicle and point E. Then check that the horizontal angle of the front side radar sensor is within the allowable range.

    *a

    Poster

    *b

    Toyota Prius Vehicle Center Line

    *c

    Point C

    *d

    Point D

    Standard:

    Item

    Allowable Range

    Front Side Radar Sensor (for LH Side)

    26 to 34°

    Front Side Radar Sensor (for RH Side)

    26 to 34°

(10) When not using a laser line marker:

  1. Check that the following dimensions are obtained based on point C and point D.

    *A

    Toyota Prius Vehicle Front (LH)

    *a

    Vehicle Front

    *b

    Vehicle Rear

    *c

    Toyota Prius Vehicle Center Line

    *d

    Line Parallel to Vehicle Center Line

    *e

    Line Perpendicular to Vehicle Center Line

    Standard:

    Location

    Measurement

    y

    24 to 31 mm (0.94 to 1.22 in.)

    HINT:

    If the results are not as specified, it is possible that the front side radar sensor installation area (frame, head light assembly) is deformed, so make corrections as necessary.

(b) Vertical mounting angle check

(1) Place the digital angle gauge on a level (gradient within 1%) and perform zero-point adjustment as shown in the illustration.

*a

( )

*b

(-)

*c

When Storing Zero Point

*d

After Storing Zero Point, Indicates 90° When Fully Horizontal

(2) Set the digital angle gauge to the outward facing surface of the front side radar sensor as shown in the illustration, and check that the perpendicular angle of the front side radar sensor is within the permissible range.

*1

Front Side Radar Sensor

*a

Digital Angle Gauge

*b

Outward Facing Surface

NOTICE:

The sensor angle is the measured sensor angle subtracted from 90°.

*a

( )

*b

(-)

*c

Horizontal Line

*d

Digital Angle Gauge

*e

Outward Facing Surface

HINT:

  • The digital angle gauge should indicate 90° when turned on its side.
  • The outward facing surface (installation angle) is positive ( ) when it faces higher than horizontal.

Standard:

Item

Allowable Range

Front Side Radar Sensor (for LH Side)

-2.2 to 2.2°

Front Side Radar Sensor (for RH Side)

-2.2 to 2.2°

(c) Install the front bumper assembly.

Click here