Rear Brake Flexible Hose
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake flexible hose removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: Also necessary after performing a tire rotation. *2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location. *3: The vehicle height changes because of tire replacement. |
|||
Tires |
|
Tire Pressure Warning System |
Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) |
Rear television camera assembly optical axis (Back camera position setting)*3 |
Parking Assist Monitor System |
||
Parking assist ECU initialization*3 |
Panoramic View Monitor System |
||
Advanced Park |
|||
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the vehicleEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
for PHEV Model:
|
- |
NOTICE:
- If both left and right rear flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
REAR WHEEL |
- |
- |
- |
- |
3 |
DISABLE BRAKE CONTROL |
- |
- |
- |
|
4 |
DRAIN BRAKE FLUID |
- |
- |
- |
|
5 |
REAR FLEXIBLE HOSE |
47319F |
- |
- |
|
*1 |
BRAKE LINE |
*2 |
GASKET |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. PRECAUTION
![]() |
NOTICE: After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click here |
2. REMOVE REAR WHEEL
Click here ![]()
3. DISABLE BRAKE CONTROL
![]() |
Click here |
4. DRAIN BRAKE FLUID
![]() |
NOTICE: If brake fluid leaks onto any painted surface, immediately wash it off. |
5. REMOVE REAR FLEXIBLE HOSE
(1) Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.
(2) Remove the bolt and separate the rear flexible hose.
(3) Using a union nut wrench, disconnect the brake line while holding the rear flexible hose with a wrench.
NOTICE:
- Do not kink or damage the brake line.
- Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
(4) Remove the clip and rear flexible hose from the vehicle body.
Installation
INSTALLATION
NOTICE:
- Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the rear flexible hoses.
- When reusing the rear flexible hoses, use the identification marks created during removal to install each rear flexible hose to its original position.
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR FLEXIBLE HOSE |
47319F |
- |
- |
|
2 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
3 |
BLEED BRAKE LINE |
- |
- |
- |
|
4 |
REAR WHEEL |
- |
- |
- |
- |
5 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
*1 |
BRAKE LINE |
*2 |
GASKET |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
* |
For use with a union nut wrench |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. INSTALL REAR FLEXIBLE HOSE
![]() |
NOTICE: When installing the rear flexible hose, minimize twisting of the hose. |
*a |
Identification Mark |
*b |
Union Nut Wrench |
*c |
Torque Wrench Fulcrum Length |
- |
- |
(1) Install the rear flexible hose with a new clip.
NOTICE:
Install the clip as far as it will go.
(2) Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.
Torque:
Specified tightening torque :
15,2 N·m {155 kgf·cm, 11 ft·lbf}
NOTICE:
- Do not kink or damage the brake line.
- Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here

- When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
(3) Install the rear flexible hose with the bolt.
Torque:
29 N·m {296 kgf·cm, 21 ft·lbf}
(4) Install the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Torque:
30 N·m {310 kgf·cm, 22 ft·lbf}
NOTICE:
Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.
2. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
![]() |
Click here |
3. BLEED BRAKE LINE
Click here ![]()
4. INSTALL REAR WHEEL
Click here ![]()
5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()


























