Roof Garnish
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof top moulding sub-assembly removal/installation are shown below.
NOTICE:
- After the ignition switch is turned off, the radio and display receiver assembly recordsvarious types of memory and settings. As a result, after turning the ignition switch off,make sure to wait at least 3 minutes before disconnecting the cable from the negative(-) auxiliary battery terminal.
Click here

- When the cable is disconnected from the negative (-) auxiliary battery terminal and thesecurity lock setting has been enabled, multi-display operations will be disabled uponnext startup unless the password is entered. Be sure to check the security lock settingbefore disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here

HINT:
- When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. Learning completes when Toyota Prius vehicle is driven
Learning completes when vehicle is operated normallyEffect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
- Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
for HEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
- After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.
-
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
2 |
ROOF TOP MOULDING SUB-ASSEMBLY |
75607B |
- |
- |
|
PROCEDURE
1. REMOVE ROOF HEADLINING ASSEMBLY
Click here ![]()
2. REMOVE ROOF TOP MOULDING SUB-ASSEMBLY

(1) Apply protective tape around the roof top moulding sub-assembly as shown in the illustration.

(1) Remove the 14 nuts.

![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
(1) Remove the roof top moulding sub-assembly, in the order shown in the illustration.
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
ROOF TOP MOULDING SUB-ASSEMBLY |
75607B |
- |
- |
|
2 |
ROOF HEADLINING ASSEMBLY |
- |
- |
- |
- |
PROCEDURE
1. INSTALL ROOF TOP MOULDING SUB-ASSEMBLY

![]() |
Protective Tape |
- |
- |
(1) Pull back the front moon roof moulding and secure it with protective tape as shown in the illustration.
NOTICE:
Be careful not to damage the front moon roof moulding.

![]() |
Install in this Direction (1) |
![]() |
Install in this Direction (2) |
(1) Temporarily install the roof top moulding sub-assembly as shown in the illustration.
(2) Install the roof top moulding sub-assembly with the 14 nuts.
Torque:
7 N·m {71 kgf·cm, 62 in·lbf}
2. INSTALL ROOF HEADLINING ASSEMBLY
Click here
![]()












