Front Evaporator Temperature Sensor
- Removal
- Inspection
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 cooler thermistor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
w/ Occupant Classification System:
|
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
BLOWER ASSEMBLY |
87130D |
- |
- |
- |
2 |
NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
55086 |
- |
- |
- |
3 |
LOWER DEFROSTER NOZZLE ASSEMBLY |
55990B |
- |
- |
- |
4 |
LOWER DEFROSTER NOZZLE |
55967B |
- |
- |
- |
5 |
AIR CONDITIONING HARNESS ASSEMBLY |
82210K |
- |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
87050C |
- |
- |
- |
7 |
HEATER PIPE GROMMET |
88897M |
- |
- |
- |
8 |
HEATER CLAMP |
87124C |
- |
- |
- |
9 |
HEATER RADIATOR UNIT SUB-ASSEMBLY |
87107A |
- |
- |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
COOLER PIPE GROMMET |
88897K |
- |
- |
- |
11 |
COOLER EXPANSION VALVE |
88515 |
- |
- |
|
12 |
CONNECTOR TUBE |
- |
- |
- |
|
13 |
COOLING UNIT PARTS |
88899L |
- |
- |
- |
14 |
NO. 1 DISCHARGE TUBE |
88715M |
- |
- |
|
15 |
CONDENSER ASSEMBLY |
88460Q |
- |
- |
- |
16 |
NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
88501 |
- |
- |
|
17 |
NO. 1 COOLER THERMISTOR |
88625 |
- |
- |
- |
*A |
for HEV Model |
*B |
for PHEV Model |
*1 |
UPPER HEATER CASE |
*2 |
LOWER HEATER CASE |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE BLOWER ASSEMBLY
Click here ![]()
2. REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
3. REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Click here ![]()
4. REMOVE LOWER DEFROSTER NOZZLE
Click here ![]()
5. REMOVE AIR CONDITIONING HARNESS ASSEMBLY
Click here ![]()
6. REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
7. REMOVE HEATER PIPE GROMMET
Click here ![]()
8. REMOVE HEATER CLAMP
Click here ![]()
9. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
![]() |
Click here |
10. REMOVE COOLER PIPE GROMMET
Click here ![]()
11. REMOVE COOLER EXPANSION VALVE (for HEV Model)
![]() |
Click here |
12. REMOVE CONNECTOR TUBE (for PHEV Model)
![]() |
Click here |
13. REMOVE COOLING UNIT PARTS (for PHEV Model)
Click here ![]()
14. REMOVE NO. 1 DISCHARGE TUBE (for PHEV Model)
![]() |
Click here |
15. REMOVE CONDENSER ASSEMBLY (for PHEV Model)
Click here ![]()
16. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
![]() |
Click here |
17. REMOVE NO. 1 COOLER THERMISTOR

Inspection
INSPECTION
PROCEDURE
1. INSPECT NO. 1 COOLER THERMISTOR
(a) Measure the resistance according to the value(s) in the table below.

*a |
Component without harness connected (No. 1 Cooler Thermistor) |
*b |
Sensing Portion |
*c |
Resistance (kΩ) |
*d |
Temperature (°C (°F)) |
*e |
Allowable Range |
- |
- |
Standard Resistance:
Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
A-1 - A-2 |
-10°C (14°F) |
7.30 to 9.10 kΩ |
kΩ |
A-1 - A-2 |
-5°C (23°F) |
5.65 to 6.95 kΩ |
kΩ |
A-1 - A-2 |
0 °C |
4.40 to 5.35 kΩ |
kΩ |
A-1 - A-2 |
5 °C |
3.40 to 4.15 kΩ |
kΩ |
A-1 - A-2 |
10 °C |
2.70 to 3.25 kΩ |
kΩ |
A-1 - A-2 |
15 °C |
2.14 to 2.58 kΩ |
kΩ |
A-1 - A-2 |
20 °C |
1.71 to 2.05 kΩ |
kΩ |
A-1 - A-2 |
25 °C |
1.38 to 1.64 kΩ |
kΩ |
A-1 - A-2 |
30 °C |
1.11 to 1.32 kΩ |
kΩ |
NOTICE:
- Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.
- When measuring, the sensor temperature must be the same as the ambient temperature.
HINT:
As the temperature increases, the resistance decreases (see the graph).
If the resistance is not as specified, replace the No. 1 cooler thermistor.
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 1 COOLER THERMISTOR |
88625 |
- |
- |
|
2 |
NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
88501 |
- |
- |
|
3 |
CONDENSER ASSEMBLY |
88460Q |
- |
- |
- |
4 |
NO. 1 DISCHARGE TUBE |
88715M |
- |
- |
|
5 |
COOLING UNIT PARTS |
88899L |
- |
- |
|
6 |
CONNECTOR TUBE |
- |
- |
- |
|
7 |
COOLER EXPANSION VALVE |
88515 |
- |
- |
|
8 |
COOLER PIPE GROMMET |
88897K |
- |
- |
- |
*A |
for HEV Model |
*B |
for PHEV Model |
*1 |
UPPER HEATER CASE |
*2 |
LOWER HEATER CASE |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 11 or equivalent |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
9 |
HEATER RADIATOR UNIT SUB-ASSEMBLY |
87107A |
- |
- |
- |
10 |
HEATER CLAMP |
87124C |
- |
- |
- |
11 |
HEATER PIPE GROMMET |
88897M |
- |
- |
|
12 |
NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
87050C |
- |
- |
|

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
13 |
AIR CONDITIONING HARNESS ASSEMBLY |
82210K |
- |
- |
- |
14 |
LOWER DEFROSTER NOZZLE |
55967B |
- |
- |
- |
15 |
LOWER DEFROSTER NOZZLE ASSEMBLY |
55990B |
- |
- |
- |
16 |
NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
55086 |
- |
- |
- |
17 |
BLOWER ASSEMBLY |
87130D |
- |
- |
- |
PROCEDURE
1. INSTALL NO. 1 COOLER THERMISTOR

*a |
Securing Part |
*b |
Sensor Part |
(1) Install the No. 1 cooler thermistor as shown in the illustration.
Installation Position:
Part | Length | Part | Length |
|---|---|---|---|
A |
45 to 55 mm (1.77 to 2.17 in.) |
B |
61.1 mm (2.41 in.) |
NOTICE:
- Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.
- When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).
- After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.
- Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".
2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
![]() |
Click here |
3. INSTALL CONDENSER ASSEMBLY (for PHEV Model)
4. INSTALL NO. 1 DISCHARGE TUBE (for PHEV Model)
![]() |
Click here |
5. INSTALL COOLING UNIT PARTS (for PHEV Model)
![]() |
Click here |
6. INSTALL CONNECTOR TUBE (for PHEV Model)
![]() |
Click here |
7. INSTALL COOLER EXPANSION VALVE (for HEV Model)
![]() |
Click here |
8. INSTALL COOLER PIPE GROMMET
9. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
10. INSTALL HEATER CLAMP
11. INSTALL HEATER PIPE GROMMET
![]() |
Click here |
12. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
![]() |
Click here |
13. INSTALL AIR CONDITIONING HARNESS ASSEMBLY
14. INSTALL LOWER DEFROSTER NOZZLE
15. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
16. INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
17. INSTALL BLOWER ASSEMBLY
Click here ![]()
















































