Cylinder Head Gasket
- Installation
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
CYLINDER HEAD GASKET |
11115 |
- |
- |
|
2 |
CYLINDER HEAD SUB-ASSEMBLY |
11101 |
- |
- |
|
3 |
VALVE STEM CAP |
13716 |
- |
- |
|
4 |
VALVE LASH ADJUSTER ASSEMBLY |
13750 |
- |
- |
|
5 |
NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
13801 |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
*T1 |
1st: 49 (500, 36) 2nd: Turn 90° 3rd: Turn 45° |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
CAMSHAFT HOUSING SUB-ASSEMBLY |
11103 |
- |
- |
|
7 |
CAMSHAFT |
13511 |
- |
- |
|
8 |
NO. 2 CAMSHAFT |
13512 |
- |
- |
|
9 |
CAMSHAFT BEARING CAP |
- |
- |
- |
|
10 |
CAMSHAFT TIMING SPROCKET |
13523G |
- |
- |
|
11 |
CAMSHAFT TIMING GEAR ASSEMBLY |
13050 |
- |
- |
|
12 |
SET NO. 1 CYLINDER TO TDC (COMPRESSION) |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
13 |
NO. 1 CHAIN VIBRATION DAMPER |
13561 |
- |
- |
- |
14 |
CHAIN SUB-ASSEMBLY |
13506 |
- |
- |
|
15 |
NO. 2 CHAIN VIBRATION DAMPER |
13562 |
- |
- |
- |
16 |
CHAIN TENSIONER SLIPPER |
13559 |
- |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
17 |
ENGINE WATER PUMP ASSEMBLY |
16100 |
- |
- |
|
18 |
TEMPORARILY TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY |
11302 |
- |
- |
|
19 |
ENGINE MOUNTING BRACKET RH |
12305 |
- |
- |
|
20 |
OIL FILTER BRACKET SUB-ASSEMBLY |
15609 |
- |
- |
|
21 |
TIMING CHAIN COVER SUB-ASSEMBLY |
11302 |
- |
- |
|
22 |
TIMING CHAIN COVER OIL SEAL |
11302A |
- |
- |
|
23 |
NO. 1 CHAIN TENSIONER ASSEMBLY |
13540 |
- |
- |
|
24 |
CRANKSHAFT PULLEY |
13471 |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
MP grease |
![]() |
Adhesive 1324 |
★ |
Precoated part |
![]() |
Do not apply lubricants to the threaded parts |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
25 |
SPARK PLUG TUBE GASKET |
11193 |
- |
- |
- |
26 |
CYLINDER HEAD COVER GASKET |
11213 |
- |
- |
|
27 |
CYLINDER HEAD COVER SUB-ASSEMBLY |
11201 |
- |
- |
|
28 |
CAMSHAFT POSITION SENSOR |
11101E |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
29 |
IGNITION COIL ASSEMBLY |
19500 |
- |
- |
|
30 |
FUEL INJECTOR ASSEMBLY |
23250 |
- |
- |
|
31 |
NO. 1 DELIVERY PIPE SPACER |
23807V |
- |
- |
|
32 |
FUEL DELIVERY PIPE SUB-ASSEMBLY |
23807 |
- |
- |
|
33 |
FUEL VAPOR FEED PIPE |
23818 |
- |
- |
- |
34 |
PURGE VALVE (PURGE VSV) |
17650G |
- |
- |
- |
35 |
WATER BY-PASS PIPE |
16268L |
- |
- |
- |
36 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
11452 |
- |
- |
- |
37 |
ENGINE OIL LEVEL DIPSTICK |
15301 |
- |
- |
- |
38 |
INTAKE MANIFOLD |
17111 |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic Toyota Prius vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
39 |
EXHAUST MANIFOLD (TWC: Front Catalyst) |
17141 |
- |
- |
|
40 |
MANIFOLD STAY |
17118 |
- |
- |
|
41 |
NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
17167 |
- |
- |
- |
42 |
TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER |
25601L |
- |
- |
|
43 |
TEMPORARILY INSTALL EGR PIPE ASSEMBLY |
25610 |
- |
- |
- |
44 |
INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER |
25601L |
- |
- |
- |
45 |
INSTALL EGR PIPE ASSEMBLY |
25610 |
- |
- |
- |
46 |
WATER OUTLET |
16331 |
- |
- |
- |
47 |
ENGINE HANGERS |
- |
- |
- |
|
48 |
REMOVE ENGINE FROM ENGINE STAND |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
PROCEDURE
1. INSTALL CYLINDER HEAD GASKET

*1 |
Cylinder Block Sub-assembly |
- |
- |
*a |
2.0 to 4.0 mm (0.079 to 0.157 in.) |
*b |
10 to 15 mm (0.394 to 0.591 in.) |
*c |
Diameter 4.0 mm (0.1575 in.) |
*d |
Lot No. |
![]() |
Front of Engine |
- |
- |
(1) Remove any oil from the contact surfaces.
(2) Apply seal packing to the cylinder block sub-assembly as shown in the illustration.
NOTICE:
Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes of applying seal packing.
(3) Place a new cylinder head gasket on the cylinder block sub-assembly as shown in the illustration.
NOTICE:
Make sure to install the cylinder head gasket in the correct direction.

*1 |
Cylinder Head Gasket |
- |
- |
*a |
Diameter 6 to 8 mm (0.236 to 0.315 in.) |
- |
- |
![]() |
Front of Engine |
- |
- |
(1) Apply seal packing to the cylinder head gasket as shown in the illustration.
2. INSTALL CYLINDER HEAD SUB-ASSEMBLY
![]() |
Click here |
3. INSTALL VALVE STEM CAP
![]() |
Click here |
4. INSTALL VALVE LASH ADJUSTER ASSEMBLY
![]() |
Click here |
5. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
![]() |
Click here |
6. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY
![]() |
Click here |
7. INSTALL CAMSHAFT
![]() |
Click here |
8. INSTALL NO. 2 CAMSHAFT
![]() |
Click here |
9. INSTALL CAMSHAFT BEARING CAP
![]() |
Click here |
10. INSTALL CAMSHAFT TIMING SPROCKET
![]() |
Click here |
11. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
![]() |
Click here |
12. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
![]() |
Click here |
13. INSTALL NO. 1 CHAIN VIBRATION DAMPER
Click here ![]()
14. INSTALL CHAIN SUB-ASSEMBLY
![]() |
HINT:
|

(1) Temporarily install the crankshaft pulley set bolt to the crankshaft.

*a |
Place the chain sub-assembly on the sprocket |
*b |
Pass the chain sub-assembly through the damper |
*c |
Mark Plate (Orange) |
*d |
Timing Mark (Rectangle) |
*e |
Mark (Circle) |
- |
- |
(1) Install the chain sub-assembly with the mark plates (orange) of the chain sub-assembly aligned with the timing mark (rectangle) as shown in the illustration.
HINT:
- There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).
- Do not pass the chain sub-assembly around the sprocket of the camshaft timing gear assembly. Only place it on the camshaft timing gear assembly.
- Pass the chain sub-assembly through the No. 1 chain vibration damper.
(2) Place the chain sub-assembly on the crankshaft without passing it around the crankshaft.

*a |
Tension the chain sub-assembly |
*b |
Mark Plate (Orange) |
*c |
Timing Mark |
- |
- |
(1) Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to align the mark plate (orange) with timing mark, and then install the chain sub-assembly.
HINT:
If the camshaft timing gear assembly cannot be positioned as shown in the illustration, using a wrench to hold the hexagonal portion of the camshaft, slightly rotate the camshaft timing gear assembly counterclockwise and then install the chain sub-assembly.
(2) Using a wrench to hold the hexagonal portion of the camshaft, slowly turn the camshaft timing gear assembly clockwise to tension the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.
HINT:
Make sure to turn the camshaft timing gear assembly slowly to prevent the camshaft timing sprocket from becoming misaligned.

*a |
Timing Mark |
*b |
Mark Plate (Yellow or Pink) |
(1) Align the mark plate (Yellow or Pink) with timing mark and install the chain sub-assembly to the crankshaft timing sprocket.

*a |
Mark Plate (Orange) |
*b |
Mark Plate (Yellow or Pink) |
*c |
Timing Mark |
*d |
Timing Mark (Rectangle) |
*e |
Mark (Circle) |
- |
- |
(1) Check that each timing mark is at TDC (compression).
HINT:
There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.
(2) Remove the crankshaft pulley set bolt from the crankshaft.
15. INSTALL NO. 2 CHAIN VIBRATION DAMPER
Click here ![]()
16. INSTALL CHAIN TENSIONER SLIPPER
Click here ![]()
17. INSTALL ENGINE WATER PUMP ASSEMBLY
![]() |
Click here |
18. TEMPORARILY TIGHTEN TIMING CHAIN COVER SUB-ASSEMBLY
![]() |
Click here |
19. INSTALL ENGINE MOUNTING BRACKET RH
![]() |
Click here |
20. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
![]() |
Click here |
21. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
![]() |
Click here |
22. INSTALL TIMING CHAIN COVER OIL SEAL
![]() |
Click here |
23. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
![]() |
Click here |
24. INSTALL CRANKSHAFT PULLEY
![]() |
Click here |
25. INSTALL SPARK PLUG TUBE GASKET
Click here ![]()
26. INSTALL CYLINDER HEAD COVER GASKET
![]() |
Click here |
27. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
![]() |
Click here |
28. INSTALL CAMSHAFT POSITION SENSOR
![]() |
Click here |
29. INSTALL IGNITION COIL ASSEMBLY
![]() |
Click here |
30. INSTALL FUEL INJECTOR ASSEMBLY
![]() |
Click here |
31. INSTALL NO. 1 DELIVERY PIPE SPACER
![]() |
Click here |
32. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
![]() |
Click here |
33. INSTALL FUEL VAPOR FEED PIPE
Click here ![]()
34. INSTALL PURGE VALVE (PURGE VSV)
Click here ![]()
35. INSTALL WATER BY-PASS PIPE
Click here ![]()
36. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Click here ![]()
37. INSTALL ENGINE OIL LEVEL DIPSTICK
Click here ![]()
38. INSTALL INTAKE MANIFOLD
![]() |
Click here |
39. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)
![]() |
Click here |
40. INSTALL MANIFOLD STAY
![]() |
Click here |
41. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Click here ![]()
42. TEMPORARILY INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER
![]() |
Click here |
43. TEMPORARILY INSTALL EGR PIPE ASSEMBLY
Click here ![]()
44. INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER
Click here ![]()
45. INSTALL EGR PIPE ASSEMBLY
Click here ![]()
46. INSTALL WATER OUTLET
Click here ![]()
47. INSTALL ENGINE HANGERS
![]() |
Click here |
48. REMOVE ENGINE FROM ENGINE STAND
Click here ![]()




































































































