Front Door Belt Moulding
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
|
Side television camera view adjustment |
Parking Support Brake system |
|
Panoramic View Monitor System |
|||
Advanced Park |
|||
Replacement or removal and installation of 2 or more parts:
|
Television camera view adjustment |
Panoramic View Monitor System |
|
|
Initialize power window control system |
|
|
HINT:
- When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. Learning completes when Toyota Prius vehicle is driven
Learning completes when vehicle is operated normallyEffect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
- Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
for HEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
- After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.
-
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FRONT DOOR GLASS SUB-ASSEMBLY |
68102 |
- |
- |
- |
2 |
FRONT DOOR LOWER FRAME BRACKET GARNISH |
67492A |
- |
- |
- |
3 |
NO. 3 FRONT DOOR SERVICE HOLE COVER |
67836C |
- |
- |
- |
4 |
OUTER REAR VIEW MIRROR ASSEMBLY |
87940 |
- |
- |
- |
5 |
FRONT DOOR BELT MOULDING ASSEMBLY |
75720 |
- |
- |
|
*1 |
HOOK |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here ![]()
2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Click here ![]()
3. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER
Click here ![]()
4. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
Click here ![]()
5. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

![]() |
Remove in this Direction |
- |
- |
(1) Apply protective tape around the front door belt moulding assembly as shown in the illustration.
(2) Disengage the 6 claws as shown in the illustration.
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FRONT DOOR BELT MOULDING ASSEMBLY |
75720 |
- |
- |
- |
2 |
OUTER REAR VIEW MIRROR ASSEMBLY |
87940 |
- |
- |
- |
3 |
NO. 3 FRONT DOOR SERVICE HOLE COVER |
67836C |
- |
- |
- |
4 |
FRONT DOOR LOWER FRAME BRACKET GARNISH |
67492A |
- |
- |
- |
5 |
FRONT DOOR GLASS SUB-ASSEMBLY |
68102 |
- |
- |
- |
*1 |
HOOK |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
PROCEDURE
1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
2. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
Click here ![]()
3. INSTALL NO. 3 FRONT DOOR SERVICE HOLE COVER
4. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
5. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Click here ![]()













