Discharge Temperature Sensor
- Removal
- Inspection
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during discharge temperature sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
w/ Occupant Classification System:
|
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.

Click here ![]()
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
for HEV Model:
|
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
AIR CONDITIONER UNIT ASSEMBLY |
- |
- |
- |
- |
2 |
AIR CONDITIONING AMPLIFIER ASSEMBLY |
88650N |
- |
- |
- |
3 |
COOLING UNIT PARTS |
88899L |
- |
- |
- |
4 |
NO. 1 DISCHARGE TUBE |
88715M |
- |
- |
|
5 |
NO. 1 COOLING UNIT PACKING |
88578B |
- |
- |
- |
6 |
DISCHARGE TEMPERATURE SENSOR |
88620H |
- |
- |
- |
*1 |
CLAMP |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE AIR CONDITIONER UNIT ASSEMBLY
Click here ![]()
2. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
Click here ![]()
3. REMOVE COOLING UNIT PARTS
Click here ![]()
4. REMOVE NO. 1 DISCHARGE TUBE
![]() |
Click here |
5. REMOVE NO. 1 COOLING UNIT PACKING

6. REMOVE DISCHARGE TEMPERATURE SENSOR

Inspection
INSPECTION
PROCEDURE
1. INSPECT DISCHARGE TEMPERATURE SENSOR
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE:
HINT: As the temperature increases, the resistance decreases (see the graph).
|
|
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
DISCHARGE TEMPERATURE SENSOR |
88620H |
- |
- |
- |
2 |
NO. 1 COOLING UNIT PACKING |
88578B |
- |
- |
|
3 |
NO. 1 DISCHARGE TUBE |
88715M |
- |
- |
|
4 |
COOLING UNIT PARTS |
88899L |
- |
- |
|
5 |
AIR CONDITIONING AMPLIFIER ASSEMBLY |
88650N |
- |
- |
- |
6 |
AIR CONDITIONER UNIT ASSEMBLY |
- |
- |
- |
- |
*1 |
CLAMP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 11 or equivalent |
- |
- |
PROCEDURE
1. INSTALL DISCHARGE TEMPERATURE SENSOR
2. INSTALL NO. 1 COOLING UNIT PACKING

*1 |
NO. 1 DISCHARGE TUBE |
*2 |
CLAMP |
*3 |
DISCHARGE TEMPERATURE SENSOR |
*4 |
NO. 1 COOLING UNIT PACKING |
*a |
View A |
- |
- |
(1) Perform the following procedure to install the No. 1 cooling unit packing.
1. Remove any remaining No. 1 cooling unit packing from the discharge temperature sensor and No. 1 discharge tube.
2. Remove the release paper from a new No. 1 cooling unit packing.
3. Install the No. 1 cooling unit packing as shown in the illustration.
NOTICE:
Make sure to install the cooler packing so that its ends are on the opposite side of the discharge temperature sensor as shown in the illustration.
3. INSTALL NO. 1 DISCHARGE TUBE
![]() |
Click here |
4. INSTALL COOLING UNIT PARTS
![]() |
Click here |
5. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
Click here ![]()
6. INSTALL AIR CONDITIONER UNIT ASSEMBLY
Click here ![]()



















