Fuel Pressure Regulator
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pressure regulator assembly removal/installation are shown below.
CAUTION:
- Never perform work on fuel system components near any possible ignition sources.

- Vaporized fuel could ignite, resulting in a serious accident.
- Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

- Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when Toyota Prius vehicle is drivenEffect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
Front Camera System |
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more. |
Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| *1: w/o Power Back Door System *2: w/ Power Back Door System |
||
Power Door Lock Control System*1
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
Power Back Door System*2 |
Reset back door close position |
|
Air Conditioning System |
After the ignition switch is turned to ON, the servo motor standard position is recognized. |
- |

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
77020A |
- |
- |
- |
2 |
NO. 2 FUEL SUCTION SUPPORT |
77175 |
- |
- |
- |
3 |
FUEL PRESSURE REGULATOR ASSEMBLY |
23280J |
- |
- |
|
● |
Non-reusable part |
- |
- |
PROCEDURE
1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here ![]()
2. REMOVE NO. 2 FUEL SUCTION SUPPORT

3. REMOVE FUEL PRESSURE REGULATOR ASSEMBLY

(1) Using a screwdriver with its tip wrapped with protective tape, remove the fuel pressure regulator assembly from the fuel suction tube with pump and gauge assembly.
NOTICE:
- Pull out the fuel pressure regulator assembly carefully because the O-rings are firmly installed between the fuel pressure regulator assembly and the fuel suction tube with pump and gauge assembly.
- Do not damage the fuel suction tube with pump and gauge assembly.
(2) Remove the 2 O-rings from the fuel pressure regulator assembly.
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
FUEL PRESSURE REGULATOR ASSEMBLY |
23280J |
- |
- |
|
2 |
NO. 2 FUEL SUCTION SUPPORT |
77175 |
- |
- |
- |
3 |
FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
77020A |
- |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. INSTALL FUEL PRESSURE REGULATOR ASSEMBLY

(1) Apply gasoline to 2 new O-rings. Then install the O-rings to the fuel pressure regulator assembly.
(2) Install the fuel pressure regulator assembly to the fuel suction tube with pump and gauge assembly.
NOTICE:
Make sure that the O-rings are not cut or pinched during installation.
2. INSTALL NO. 2 FUEL SUCTION SUPPORT
3. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
Click here ![]()










