Service Plug Grip (for Hev Model)
- Removal
- Inspection
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during service plug grip removal/installation are shown below.
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click here

- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here ![]()
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Items for which learning is completed by driving the Toyota Prius vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more.

- Items for which learning is completed by operating the vehicle normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
CHECK FOR DTC |
- |
- |
- |
|
2 |
NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
3 |
BATTERY SERVICE HOLE COVER |
58441M |
- |
- |
- |
4 |
SERVICE PLUG GRIP |
G3834 |
- |
- |
|
PROCEDURE
1. CHECK FOR DTC

(1) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes Powertrain > HV Battery > Trouble Codes Powertrain > Motor Generator > Trouble CodesCAUTION:
- Confirm that DTC P0AA649 (Hybrid / EV Battery Voltage System Isolation Internal Electronic Failure), P1C7C49 (Hybrid / EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure), P1C7D49 (Hybrid / EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure), P1C7E49 (Hybrid / EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure) or P1C7F49 (Hybrid / EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure) are not output before removing or installing the HV battery. If this DTC is output, perform troubleshooting for this DTC first.

- To reduce the risk of electric shock, do not perform troubleshooting before checking for DTCs.
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
![]() |
|
3. REMOVE BATTERY SERVICE HOLE COVER

4. REMOVE SERVICE PLUG GRIP
![]() |
CAUTION:
NOTICE:
|

![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
![]() |
Remove in this Direction (3) |
- |
- |
(1) While wearing insulated gloves, rotate the handle of the service plug grip and remove the service plug grip as indicated by the arrows, in the order shown in the illustration.
Inspection
INSPECTION
PROCEDURE
1. INSPECT SERVICE PLUG GRIP
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the service plug grip. |
![]() |
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
SERVICE PLUG GRIP |
G3834 |
- |
- |
|
2 |
BATTERY SERVICE HOLE COVER |
58441M |
- |
- |
- |
3 |
NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
4 |
PERFORM INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
PROCEDURE
1. INSTALL SERVICE PLUG GRIP
![]() |
CAUTION: Be sure to wear insulated gloves. NOTICE:
|

![]() |
Install in this Direction (1) |
![]() |
Install in this Direction (2) |
![]() |
Install in this Direction (3) |
- |
- |
(1) While wearing insulated gloves, and temporarily install the service plug grip as indicated by the arrow (1) shown in the illustration.
2. INSTALL BATTERY SERVICE HOLE COVER
3. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
- for M20A-FXS:
Click here

- for 2ZR-FXE:
Click here

4. PERFORM INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()






















