Integration Control Supply
- Removal
- Installation
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during integration control supply removal/installation are shown below.
NOTICE:
- When disconnecting a wire harness of any component connected to the supply power of the integrated capacitor (integration control supply) or when removing the integrated capacitor (integration control supply), make sure to wait 5 minutes or more after turning the ignition switch off for self-diagnosis to complete and the voltage of the integrated capacitor (integration control supply) to discharge.
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here

HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Items for which learning is completed by driving the Toyota Prius vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 second or more.

- Items for which learning is completed by operating the vehicle normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: w/o Power Back Door System *2: w/ Power Back Door System
Power Door Lock Control System*1
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2
Reset back door close position

Air Conditioning System
for HEV Model: - After the ignition switch is turned to ON, the servo motor standard position is recognized.
- After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.
-

Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
2 |
REAR CONSOLE BOX ASSEMBLY |
58910C |
- |
- |
|
3 |
INTEGRATION CONTROL SUPPLY |
28912 |
- |
- |
- |
4 |
NO. 1 INTEGRATION CONTROL SUPPLY BRACKET |
28911 |
- |
- |
- |
5 |
NO. 2 INTEGRATION CONTROL SUPPLY BRACKET |
28911A |
- |
- |
- |
6 |
INTEGRATION CONTROL COVER |
28913 |
- |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
2. REMOVE REAR CONSOLE BOX ASSEMBLY
![]() |
Click here |
3. REMOVE INTEGRATION CONTROL SUPPLY

![]() |
Remove in this Direction |
- |
- |
(1) Disconnect the connector.
(2) Remove the 2 bolts.
(3) Slide the integration control supply as shown in the illustration to remove it.
4. REMOVE NO. 1 INTEGRATION CONTROL SUPPLY BRACKET

5. REMOVE NO. 2 INTEGRATION CONTROL SUPPLY BRACKET

6. REMOVE INTEGRATION CONTROL COVER
HINT:
Perform this procedure only when replacement of the integration control cover is necessary.

*1 |
Integration Control Cover |
- |
- |
Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INTEGRATION CONTROL COVER |
28913 |
- |
- |
|
2 |
NO. 2 INTEGRATION CONTROL SUPPLY BRACKET |
28911A |
- |
- |
- |
3 |
NO. 1 INTEGRATION CONTROL SUPPLY BRACKET |
28911 |
- |
- |
- |
4 |
INTEGRATION CONTROL SUPPLY |
28912 |
- |
- |
- |
5 |
CONSOLE BOX ASSEMBLY REAR |
58910C |
- |
- |
|
6 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
7 |
INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque) |
- |
- |
● |
Non-reusable part |
- |
- |
PROCEDURE
1. INSTALL INTEGRATION CONTROL COVER

*1 |
Integration Control Cover |
- |
- |
![]() |
Attachment Area |
- |
- |
(1) Install a new integration control cover so that it does not protrude from the area shown in the illustration of the integration control supply.
2. INSTALL NO. 2 INTEGRATION CONTROL SUPPLY BRACKET
Torque:
4,5 N·m {46 kgf·cm, 40 in·lbf}
3. INSTALL NO. 1 INTEGRATION CONTROL SUPPLY BRACKET
Torque:
4,5 N·m {46 kgf·cm, 40 in·lbf}
4. INSTALL INTEGRATION CONTROL SUPPLY

![]() |
Install in this Direction |
- |
- |
(1) Slide and temporarily install the integration control supply as shown in the illustration.
(2) Install the integration control supply with the 2 bolts.
Torque:
13 N·m {133 kgf·cm, 10 ft·lbf}
(3) Connect the connector.
5. INSTALL REAR CONSOLE BOX ASSEMBLY
![]() |
Click here |
6. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for M20A-FXS:
Click here ![]()
(b) for 2ZR-FXE:
Click here ![]()
7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
![]()















