Tire Pressure Warning Receiver

In this manual: Tire Pressure Warning Receiver
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
~26min read
01020304050107N·mlb·ft
Tightening torque found on this page
  • Registration
  • Initialization
  • Removal
  • Installation

Registration

REGISTRATION

PROCEDURE

1. BEFORE REGISTRATION

NOTICE:

  • The transmitter ID is written on the tire pressure warning valve and transmitter. It is not possible to read the transmitter ID after installing the tire onto the wheel. Therefore, make a note of the transmitter ID before installing the tire.
  • Tire pressure warning ECU and receiver ID registration after replacement must be performed using the GTS.
  • Be sure to check procedures or what work is required after replacing parts.

    Click here

(a) When replacing tire pressure warning ECU and receiver:

(1) Before replacing, use the GTS to read and record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

(2) If reading the stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valve and transmitters.

(b) When replacing tire pressure warning valve and transmitter:

(1) Take a note of the 7-digit number (transmitter ID) written on the tire pressure warning valve and transmitter.

*1

Tire Pressure Warning Valve and Transmitter

*a

Transmitter ID (7-digit Number)

2. REGISTER TRANSMITTER ID (USING GTS)

HINT:

If the ID registration step is not completed within 300 seconds, ID registration will be canceled.

(a) Set the tire pressure to the specified value.

Click here

(b) On the GTS screen, display "ID Registration/Tire Number Registration" of Utility.

Chassis > Tire Pressure Monitor > Utility

ID Registration/Tire Number Registration

(c) Perform the procedure displayed on the GTS.

HINT:

The number of tires with transmitters can be changed to 4 wheels only when the default value is set to 5 wheels. The number of tires is changed only when there is a special request from the customer. Normally, the default value for the number of tires is set.

3. TIRE POSITION IDENTIFICATION (USING GTS)

(a) Set the tire pressure to the specified value.

Click here

(b) On the GTS screen, display the Data List.

(c) Refer to the table below to check the tire pressure with the Data List.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID1 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 2 Tire Inflation Pressure

ID2 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 3 Tire Inflation Pressure

ID3 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 4 Tire Inflation Pressure

ID4 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

HINT:

  • *: It may take a few minutes until the values are displayed.
  • The wheel position cannot be determined from ID1 through ID4 on the Data List.
Chassis > Tire Pressure Monitor > Data List

Tester Display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

(d) Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

NOTICE:

  • It may take a few minutes until the values are displayed.
  • When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.

(e) Read the "ID Tire Inflation Pressure" value and identify the tire with reduced pressure, and record the corresponding tire pressure warning valve and transmitter (ID1 to ID4).

(f) Repeat for each tire.

(g) Set the tire pressure to the specified value.

Click here

(h) On the GTS screen, display "ID Registration/Tire Position Write" of Utility.

Chassis > Tire Pressure Monitor > Utility

ID Registration/Tire Position Write

(i) Perform the procedure displayed on the GTS.

4. REGISTER TRANSMITTER ID (USING TPWS TRIGGER TOOL)

HINT:

TPWS is an abbreviation for Tire Pressure Warning System.

(a) Temporary registration:

(1) Adjust the tire pressure in all tires to the specified pressure.

Click here

(2) Set the TPWS trigger tool to the ID reading screen.

*a

TPWS Trigger Tool (ATEQ VT30, VT36, VT55 or VT56)

*b

Read Button

(3) Step "A":

Turn the ignition switch to ON.

(4) Using the steering pad switch assembly, select "Tire Set Switching" and then "Register New Valve / ID" on the multi-information display, check that the tire pressure warning light blinks, and then perform Step "B" within 35 seconds.

HINT:

During registration, the tire pressure warning light illuminates after blinking for 1.0 minutes and the tire pressure on the multi-information display displays "---".

*1

Tire Pressure Warning Light

*2

"OK" Switch (Steering Pad Switch Assembly)

*a

Tire Pressure Warning Light Output Pattern

*b

ON (Illuminated)

*c

OFF (Not illuminated)

*d

0.5 sec.

*e

3 sec.

(5) Step "B":

On the TPWS trigger tool, operate the read button at the location shown in the illustration 2 times* to read and provisionally register the ID code of the tire pressure warning valve and transmitter.

HINT:

*: Read Button Operation -> Tire Pressure Screen Display (1 time) -> Read Button Operation -> Tire Pressure Screen Display (2 times)

Sequence

Position

1

Front Tire RH

NOTICE:

Operate the TPWS trigger tool while facing and close to each tire pressure warning valve and transmitter.

HINT:

  • During the registration procedure, the tire pressure warning light will blink continuously at 0.25 second intervals.
  • If registration fails, the tire pressure warning light blinks for 1 minute before turning on and the tire pressure display in the multi-information display becomes "- - -", so perform the procedure from Step "A" again.
  • When the temporary registration of each tire is completed, the hazard lights flash 2 times.
  • If the hazard lights do not flash 2 times, the tire pressure warning valve and transmitter ID of a different Toyota Prius vehicle was mistakenly registered, or the radio waves were not received. Change location, turn the ignition switch from off → ON, and perform the operation again.
Step "B"

*a

Read Button

(6) Step "C":

On the TPWS trigger tool, operate the read button at the location shown in the illustration 2 times* to read and provisionally register the ID code of the tire pressure warning valve and transmitter.

HINT:

*: Read Button Operation -> Tire Pressure Screen Display (1 time) -> Read Button Operation -> Tire Pressure Screen Display (2 times)

Sequence

Position

2

Rear Tire RH

3

Rear Tire LH

4

Front Tire LH

NOTICE:

  • Be sure to follow the sequence in the illustration. Otherwise, if provisional registration in a sequence different from the illustration is performed, incorrect tire positions will be provisionally registered.
  • Operate the TPWS trigger tool while facing and close to each tire pressure warning valve and transmitter.

HINT:

  • During the registration procedure, the tire pressure warning light will blink continuously at 0.25 second intervals.
  • If registration fails, the tire pressure warning light blinks for 1 minute before turning on and the tire pressure display in the multi-information display becomes "- - -", so perform the procedure from Step "A" again.
  • When the temporary registration of each tire is completed, the hazard lights flash 2 times.
  • Perform the operations from Step "B" to Step "C" within 60 seconds.
  • If the hazard lights do not flash 2 times, the tire pressure warning valve and transmitter ID of a different Toyota Prius vehicle was mistakenly registered, or the radio waves were not received. Change location, turn the ignition switch from off → ON, and perform the operation again
Step "C"

*a

Read Button

(7) Check that the tire pressure is "0" on the multi-information display.

HINT:

If the tire pressure is not "0", the temporary registration is not completed. Perform the procedure again from Step "A".

(b) Main registration and tire position registration:

(1) Step "D":

Following the sequence shown, on the TPWS trigger tool, operate the read button 1 time* at each location shown in the illustration to read and perform final registration for each tire pressure warning valve and transmitter ID and register the wheel position.

HINT:

*: Read Button Operation -> Tire Pressure Screen Display (1 time)

Sequence

Position

1

Front Tire RH

2

Rear Tire RH

3

Rear Tire LH

4

Front Tire LH

NOTICE:

  • If the order is incorrect, it will not be possible to complete final registration.
  • Operate the TPWS trigger tool while facing and close to each tire pressure warning valve and transmitter.

HINT:

  • During the registration procedure, the tire pressure warning light will blink continuously at 0.25 second intervals.
  • If registration fails, the tire pressure warning light blinks for 1 minute before turning on and the tire pressure display in the multi-information display becomes "- - -", so perform the procedure from Step "A" again.
  • When the temporary registration of each tire is completed, the hazard lights flash 2 times.
  • Perform the operations in Step "D" within 60 seconds.
  • If the hazard lights do not flash 2 times, the tire pressure warning valve and transmitter ID of a different Toyota Prius vehicle was mistakenly registered, or the radio waves were not received. Change location, turn the ignition switch from off → ON, and perform the operation again.
Step "D"

*a

Read Button

(2) Check that the tire pressure is displayed on the multi-information display.

(c) Rapidly decrease the tire pressure of each wheel to 40 kPa (0.4 kgf/cm2, 5.8 psi) or more within 30 seconds, and then check the tire pressure value on the multi-information display.

HINT:

  • It may take a few minutes until the values are displayed.
  • If the tire pressure data does not change, rotate the tire from 90° to 270°, and check it again.

(d) Repeat for each tire.

(e) Adjust the tire pressure in all tires to the specified pressure.

Click here

5. TIRE POSITION IDENTIFICATION (USING TPWS TRIGGER TOOL)

HINT:

TPWS is an abbreviation for Tire Pressure Warning System.

(a) Read tire pressure warning valve and transmitter ID codes and register wheel positions:

(1) Adjust the tire pressure in all tires to the specified pressure.

Click here

(2) Set the TPWS trigger tool to the ID reading screen.

*a

TPWS Trigger Tool (ATEQ VT30, VT36, VT55 or VT56)

*b

Read Button

(3) Turn the ignition switch to ON.

(4) Using the steering pad switch assembly, select "Tire Rotation" on the multi-information display and check that the tire pressure warning light blinks 3 times.

HINT:

During registration, the tire pressure on the multi-information display displays "---".

(5) Step "A":

Following the sequence shown, on the TPWS trigger tool, operate the read button 1 time* at each location shown in the illustration to read each tire pressure warning valve and transmitter ID and register the wheel position.

HINT:

*: Read Button Operation -> Tire Pressure Screen Display (1 time)

Sequence

Position

1

Front Tire RH

2

Rear Tire RH

3

Rear Tire LH

4

Front Tire LH

NOTICE:

  • If the order is incorrect, it will not be possible to complete final registration.
  • Operate the TPWS trigger tool while facing and close to each tire pressure warning valve and transmitter.

HINT:

  • When the wheel position registration of each tire is completed, the hazard lights flash 2 times.
  • Perform the operations in Step "A" within 60 seconds.
  • If the hazard lights do not flash 2 times, the tire pressure warning valve and transmitter ID of a different Toyota Prius vehicle was mistakenly registered, or the radio waves were not received. Change location, turn the ignition switch from off → ON, and perform the operation again.
Step "A"

*a

Read Button

(6) Check that the tire pressure is displayed on the multi-information display.

(b) Rapidly decrease the tire pressure of each wheel to 40 kPa (0.4 kgf/cm2, 5.8 psi) or more within 30 seconds, and then check the tire pressure value on the multi-information display.

HINT:

  • It may take a few minutes until the values are displayed.
  • If the tire pressure data does not change, rotate the tire from 90° to 270°, and check it again.

(c) Repeat for each tire.

(d) Adjust the tire pressure in all tires to the specified pressure.

Click here

6. REGISTER TRANSMITTER ID (USING AUTOMATIC ID REGISTRATION FUNCTION)

NOTICE:

  • If the transmitter IDs have not been registered, Toyota Prius Vehicle Control History (RoB) X20FA is stored in the tire pressure warning ECU and receiver after 3 minutes or more.
  • If normal pressure values are displayed, the transmitter IDs have been registered correctly.
  • If another tire pressure warning valve and transmitter belonging to the same system is installed to a tire other than the one transmitter registration is being performed on, automatic ID registration does not complete.

HINT:

  • If the ECU Data List is displayed using the GTS while work is being performed, the registration mode will be canceled.
  • Registration mode can be canceled while registration is being performed by selecting "Tire Set Switching" and then "Register New Valve / ID" on the multi-information display.
  • If the ignition switch is turned off before driving during the registration procedure, registration mode will continue.

(a) Adjust the tire pressure in all tires to the specified pressure.

Click here

(b) Turn the ignition switch off and stop the Toyota Prius vehicle for 15 minutes or more.

HINT:

After stopping the vehicle for 15 minutes or more, the frequency of radio wave signals sent by the tire pressure warning valve and transmitters increases for the first few minutes of driving (8 times the normal frequency).

(c) Using the steering pad switch assembly, select "Tire Set Switching" and then "Register New Valve / ID" on the multi-information display and check that the tire pressure warning light blinks 3 times.

HINT:

During registration, the tire pressure warning light blinks for 1 minute before turning on, the multi-information display tire pressure displays as "---" and "Identify Wheel Accepted" is displayed.

(d) Drive at approximately 40 km/h for approximately 10 to 30 minutes during 1 trip.

(e) During the procedure, make 2 or more right or left turns.

HINT:

Do not drive the Toyota Prius vehicle in reverse during registration.

If the vehicle is driven in reverse during registration, the information may be reset before registration completes, and registration may take longer than normal to complete.

(f) When registration is completed, the tire pressure warning light turns off, the normal tire pressure is displayed on the multi-information display.

HINT:

  • Registration may take longer than normal in the following driving environments.
    • Toyota Prius Vehicle is often stopped
    • Vehicle is stopped for long period of time
    • Vehicle is driven in reverse
    • Vehicle is driven parallel to another vehicle with the same type of tire pressure warning valve and transmitter installed for a long duration of time
    • Vehicle was not stopped for 15 minutes or more before registration
    • Toyota Prius Vehicle was driven at 40 km/h or less for a long duration of time
    • The ignition switch is turned from ON to off during ID registration

7. TIRE POSITION IDENTIFICATION (NOT USING GTS)

(a) Set the tire pressure to the specified value.

Click here

(b) Select "Tire rotation" on the multi-information display, then drive the Toyota Prius vehicle at 40 km/h or more for 10 to 30 minutes in 1 trip until each tire position is automatically identified.

HINT:

  • When tire position identification is being performed, the tire pressure on the multi-information display is displayed as "---".
  • Do not drive the Toyota Prius vehicle in reverse gear while performing Tire Position Identification. If the vehicle is driven in reverse gear while performing Tire Position Identification, identification information will be discarded and Tire Position Identification may take longer than usual.
  • When the vehicle is driven under the following conditions, Tire Position Identification may take longer than usual.
    • The Toyota Prius vehicle is stopped frequently.
    • The vehicle is stopped for a long period of time.
    • The vehicle is driven in reverse gear.
    • The vehicle is driven on rough roads or uneven surfaces.

8. METHOD TO SWITCH ID

NOTICE:

  • If there is a malfunction in the tire pressure warning system, perform troubleshooting before switching IDs.
  • To use the ID switching function, a tire and wheel set for which the IDs have already been registered is needed.

(a) Install the tire and wheel set for which the IDs have already been registered.

(b) Turn the ignition switch to ON.

(c) Using the steering pad switch assembly, select "Tire Set Switching" and then "Register Valve / ID" on the multi-information display and check that the tire pressure warning light blinks 3 times.

HINT:

When the switch ID procedure is being performed, the tire pressure warning light blinks for 1 minute before turning on and the tire pressure on the multi-information display is displayed as "---".

*1

Tire Pressure Warning Light

*2

"OK" Switch (Steering Pad Switch Assembly)

*a

Tire Pressure Warning Light Output Pattern

*b

ON (Illuminated)

*c

OFF (Not illuminated)

*d

0.5 sec.

*e

3 sec.

(d) Stop the Toyota Prius vehicle and wait for 2 minutes.

NOTICE:

Do not drive the vehicle during the ID switching procedure. Driving the vehicle will cause it to change to the automatic ID registration mode.

(e) When ID switching is complete, the tire pressure warning light turns off and the message "Identify Wheel Accepted" stops being displayed in the multi-information display.

(f) Perform tire position identification.

Identification using GTS: Click here

Identification by driving Toyota Prius vehicle: Click here

Identification using TPWS trigger tool: Click here

HINT:

  • When wheel position identification is complete, the tire pressures are shown in the multi-information display.
  • TPWS is an abbreviation for Tire Pressure Warning System.

Initialization

INITIALIZATION

NOTICE:

  • Initialization can be confirmed through the tire pressure warning light.
  • If the ignition switch is turned off during initialization, the tire pressure warning ECU and receiver memorizes that initialization was being performed. Therefore, it is not necessary to perform the initialization procedure again after turning the ignition switch to ON. (Only when "Setting by Current Pressure" is selected.)
  • The order in which the data is received is random. (Only when "Setting by Current Pressure" is selected.)
  • If the signals from all the tire pressure warning valve and transmitters are received, initialization is completed. (Only when "Setting by Current Pressure" is selected.)
  • When "Complete" is displayed for the value of Data List item "Initialization Not Completed", the initialization is completed.

    Click here

  • Initialization is normally completed within a few minutes. (Only when "Setting by Current Pressure" is selected.)
  • If initialization has not been completed successfully, Toyota Prius Vehicle Control History (RoB) X20FE is stored after a vehicle speed of 40 km/h or more continues for 20 minutes or more. (Only when "Setting by Current Pressure" is selected.)
  • Even if initialization is performed, the existing tire positions will not be cleared. Perform the tire position identification procedure as necessary.

BEFORE INITIALIZATION

(a) Set the tire pressure to the specified value. (Only when "Setting by Current Pressure" is selected.)

NOTICE:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

Click here

INITIALIZATION PROCEDURE

HINT:

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

  • The tire pressure drops to approximately 75% or less of the tire pressure set when system initialization was performed using the steering pad switch assembly.
  • The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 75% or less of the tire pressure* when the tires are warmed.

    *: If initialization is performed and the Toyota Prius vehicle is driven for a certain period of time, the tire pressure set during system initialization is adjusted and set to the tire pressure when the tires are warmed from the driving conditions.

    NOTICE:

    If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 75% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 75% of the tire pressure set when the tires are warmed. In this case, perform initialization again.

(a) Using the steering pad switch assembly, select "Tire Pressure Setting" and then "Setting by indicated air pressure" or "Setting by Current Pressure" on the multi-information display and check that the tire pressure warning light blinks 3 times.

*1

Tire Pressure Warning Light

*2

"OK" Switch (Steering Pad Switch Assembly)

*a

Tire Pressure Warning Light Output Pattern

*b

1 sec.

*c

ON

*d

OFF

(b) Display the Data List items shown in the following table.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID1 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 2 Tire Inflation Pressure

ID2 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 3 Tire Inflation Pressure

ID3 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

ID 4 Tire Inflation Pressure

ID4 tire inflation pressure

Min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)

Max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual tire inflation pressure

Not displayed, if data has not been received.*

HINT:

  • *: It may take a few minutes until the values are displayed.
  • The wheel position cannot be determined from ID1 through ID4 on the Data List.
Chassis > Tire Pressure Monitor > Data List

Tester Display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

(c) Check that initialization has been completed.

(d) When the value of Data List item "Initialization Not Completed" is "Complete", the initialization is completed.

Chassis > Tire Pressure Monitor > Data List

Tester Display

Measurement Item

Range

Initialization Not Completed

Initialization incomplete

Complete / Not Complete

Chassis > Tire Pressure Monitor > Data List

Initialization Not Completed

Removal

REMOVAL

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning ECU and receiver removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Tire pressure warning ECU and receiver

  • ID Registration
  • Initialization
  • Tire Position Identification

Tire Pressure Warning System

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System)

w/ Rear Seat Side Airbag:

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

    Click here

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
  • When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when Toyota Prius vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Front Camera System

Drive the Toyota Prius vehicle straight ahead at 35 km/h or more for 5 seconds or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: w/o Power Back Door System

*2: w/ Power Back Door System

Power Door Lock Control System*1

  • Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Power Back Door System*2

Reset back door close position

Air Conditioning System

for HEV Model:
  • After the ignition switch is turned to ON, the servo motor standard position is recognized.
for PHEV Model:
  • After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.

-

COMPONENTS (REMOVAL)

Procedure

Part Name Code

1

ROOF SIDE INNER GARNISH ASSEMBLY LH

62480A

-

-

-

2

TIRE PRESSURE WARNING ECU AND RECEIVER

897B0A

-

-

PROCEDURE

1. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

Click here

2. REMOVE TIRE PRESSURE WARNING ECU AND RECEIVER

NOTICE:

  • Do not drop the tire pressure warning ECU and receiver, strike it with tools or subject it to impact.
  • If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.

Installation

INSTALLATION

COMPONENTS (INSTALLATION)

Procedure

Part Name Code

1

TIRE PRESSURE WARNING ECU AND RECEIVER

897B0A

-

-

2

ROOF SIDE INNER GARNISH ASSEMBLY LH

62480A

-

-

-

3

PERFORM INITIALIZATION

-

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

-

-

PROCEDURE

1. INSTALL TIRE PRESSURE WARNING ECU AND RECEIVER

NOTICE:

  • Do not drop the tire pressure warning ECU and receiver, strike it with tools or subject it to impact.
  • If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

Click here

3. PERFORM INITIALIZATION

Click here

HINT:

Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System).