Garage Door Opener System (for Digital Inner Mirror)

In this manual: Garage Door Opener System (for Digital Inner Mirror)
How To Troubleshoot Ecu Controlled Systems — 1How To Use This Manual — 1Identification Information — 1Repair Instruction — 1Terms — 12zr-fxe Air Cleaner Filter Element — 12zr-fxe Auxiliary Battery — 12zr-fxe Coolant (for Engine Coolant) — 12zr-fxe Oil And Oil Filter — 12zr-fxe Spark Plug — 1Air Conditioning Filter — 1Battery Cooling Filter — 1Brake Fluid — 1Coolant (for Inverter) — 1Front Brake Flexible Hose — 1Front Disc Brake Pad — 1Front Lower Ball Joint — 1Front Wheel Alignment — 1Front Wiper Rubber — 1General Maintenance — 1M20a-fxs Air Cleaner Filter Element — 1M20a-fxs Auxiliary Battery — 1M20a-fxs Coolant (for Engine Coolant) — 1M20a-fxs Oil And Oil Filter — 1M20a-fxs Spark Plug — 1Pa10/pb10/pb12 Hybrid Transaxle Fluid — 1Q810 Hybrid Transaxle Fluid — 1Rear Brake Flexible Hose — 1Rear Disc Brake Pad — 1Rear Wheel Alignment — 1Steering Column — 1Tire And Wheel — 1Transmitter Battery — 1When Disconnecting Or Reconnecting Battery Terminal — 1When Replacing Or Removing/installing Parts — 1Automatic High Beam Main Switch — 1Automatic High Beam System — 1Driver Monitor Camera — 1Driver Monitor Camera System — 1Driver Monitor Ecu — 1Front Camera — 1Front Camera System — 1Front Radar Sensor System — 1Front Side Radar Sensor — 1Front Side Radar Sensor System — 1Millimeter Wave Radar Sensor — 1Utility — 1Advanced Park — 1Advanced Park Main Switch — 1Amplifier Antenna — 1Audio And Visual System — 1Front Door Speaker — 1Instrument Panel Speaker — 1Microphone — 1Noise Filter — 1Pillar Speaker — 1Radio Antenna Cord (for Back Door) — 1Radio Antenna Cord (for Instrument Panel) — 1Radio Antenna Cord (for Roof) — 1Radio Receiver — 1Rear Door Speaker — 1Roof Antenna — 1Stereo Component Amplifier — 1Stereo Jack Adapter Assembly — 1Window Glass Antenna Wire — 1Back-up Battery — 1Dcm(telematics Transceiver) — 1Manual(sos)switch — 1Safety Connect System — 1Telephone And Gps Antenna (for Front Side) — 1Telephone And Gps Antenna (for Roof Side) — 1Telephone And Gps Antenna Cords — 1Garage Door Opener System (for Digital Inner Mirror) — 1Garage Door Opener System (for Ec Inner Mirror) — 1Blind Spot Monitor Sensor — 1Blind Spot Monitor System — 1Clearance Warning Ecu — 1Intuitive Parking Assist System — 1Panoramic View Monitor Switch — 1Panoramic View Monitor System — 1Parking Assist Ecu — 1Parking Assist Light — 1Parking Assist Monitor System — 1Parking Support Brake System — 1Rear View Monitor System — 1Television Camera (for Front) — 1Television Camera (for Rear) — 1Television Camera (for Side) — 1Ultrasonic Sensor (for Front) — 1Ultrasonic Sensor (for Rear) — 1Brake Actuator — 1Brake Pedal Stroke Sensor — 1Electronically Controlled Brake System — 1Front Speed Sensor — 1Rear Speed Sensor (for Awd) — 1Steering Angle Sensor — 1Brake Booster — 1Brake Fluid — 1Brake Line — 1Brake Pedal — 1Brake System — 1Electric Parking Brake Actuator — 1Electric Parking Brake Switch — 1Electric Parking Brake System — 1Forced Release — 1Front Axle Hub — 1Front Axle Hub Bolt — 1Rear Axle Carrier (for 2wd) — 1Rear Axle Carrier (for Awd) — 1Rear Axle Hub (for 2wd) — 1Rear Axle Hub (for Awd) — 1Rear Axle Hub Bolt — 1Steering Knuckle — 1Drive Shaft System — 1Front Drive Shaft Assembly — 1Rear Drive Shaft Assembly — 1Combination Switch — 1Electronic Shift Lever System — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Oil Seal — 1Hybrid Transaxle System — 1Input Shaft Oil Seal — 1Motor Cable — 1Pa10 Hybrid Vehicle Transaxle — 1Pa10 Manual Parking Lock Release — 1Pa10 Oil Cooler — 1Pb10/pb12 Hybrid Vehicle Transaxle — 1Pb10/pb12 Manual Parking Lock Release — 1Pb10/pb12 Oil Cooler — 1Shift Control Actuator — 1Shift Lever — 1Shift Lever Knob — 1Differential Side Gear Shaft — 1Hybrid Transaxle Fluid — 1Hybrid Transaxle Side Gear Oil Seal — 1Motor Cable — 1Rear Traction Motor — 1Coolant (for Engine) — 1Cooling Fan Motor — 1Cooling Fan System — 1Radiator — 1Relay — 1Thermostat — 1Water Pump — 1Canister — 1Egr Cooler — 1Egr Valve — 1Emission Control System — 1Fuel Tank Cap — 1Pcv Valve — 1Purge Valve — 1Vacuum Sensor — 1Air Fuel Ratio Sensor — 1Camshaft Oil Control Valve — 1Camshaft Position Sensor — 1Crankshaft Position Sensor — 1Ecm — 1Engine Coolant Temperature Sensor — 1Heated Oxygen Sensor — 1Ignition Coil And Spark Plug — 1Ignition System — 1Knock Sensor — 1Mass Air Flow Meter — 1Relay — 1Sfi System — 1Throttle Body — 1Camshaft — 1Cylinder Block — 1Cylinder Head — 1Cylinder Head Gasket — 1Engine — 1Engine Assembly — 1Engine Unit — 1Front Crankshaft Oil Seal — 1Rear Crankshaft Oil Seal — 1Fuel Filter — 1Fuel Injector — 1Fuel Pressure Regulator — 1Fuel Pump — 1Fuel Sender Gauge Assembly — 1Fuel System — 1Fuel Tank — 1Air Cleaner Filter Element — 1Exhaust Manifold — 1Exhaust Pipe — 1Intake Manifold — 1Intake System — 1Lubrication System — 1Oil And Oil Filter — 1Oil Pan And Oil Level Sensor — 1Oil Pressure Switch — 1Oil Pump — 1Accelerator Pedal Sensor — 1Battery Blower (for Hev Model) — 1Battery Ecu (for Hev Model) — 1Battery Ecu (for Phev Model) — 1Battery Voltage Sensor (for Phev Model) — 1Charge Cable (for Phev Model) — 1Charge Indicator (for Phev Model) — 1Charge Inlet (for Phev Model) — 1Combination Switch — 1Coolant (for Inverter) — 1Cooler (for Phev Model) — 1Electric Vehicle Charger Assembly (for Phev Model) — 1Frame Wire (for Hev Model) — 1Frame Wire (for Phev Model) — 1Heater Relay (for Phev Model) — 1Hv Battery (for Hev Model) — 1Hv Battery (for Phev Model) — 1Hv Battery Heater (for Phev Model) — 1Hv Battery Stack (for Phev Model) — 1Hv Relay Assembly (for Hev Model) — 1Hv Relay Assembly (for Phev Model) — 1Hybrid Battery System (for 2zr-fxe) — 1Hybrid Battery System (for M20a-fxs) — 1Hybrid Battery System (for Phev Model) — 1Hybrid Vehicle Control Ecu — 1Inverter With Converter (for Hev Model) — 1Motor Generator Control System (for 2zr-fxe) — 1Plug-in Charge Control System (for Phev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Service Plug Grip (for Hev Model) — 1Sub Radiator — 1Water Pump With Motor — 1Auxiliary Battery — 1Battery Current Sensor — 1Charging System — 1Solar Charging System — 1Solar Control Unit — 1Solar Roof — 1Can Communication System (for Hev Model) — 1Lin Communication System — 1Network Gateway Ecu — 1Integration Control Supply — 1Main Body Ecu — 1Power Integration System — 1Sub Battery System — 1Power Steering Ecu — 1Power Steering System — 1Heated Steering Wheel Controller — 1Heated Steering Wheel System — 1Steering Column Assembly — 1Steering Heater Switch — 1Steering Pad Switch — 1Steering System — 1Steering Wheel — 1Front Lower Ball Joint — 1Front Lower Suspension Arm (for 2zr-fxe Lh Side) — 1Front Lower Suspension Arm (for 2zr-fxe Rh Side) — 1Front Lower Suspension Arm (for M20a-fxs) — 1Front Shock Absorber — 1Front Stabilizer Bar — 1Front Suspension Member — 1Rear Coil Spring — 1Rear Lower Arm (for Awd Lh Side) — 1Rear Lower Arm (for Awd Rh Side) — 1Rear Lower Arm (for Hev Model 2wd) — 1Rear Lower Arm (for Phev Model) — 1Rear Shock Absorber — 1Rear Stabilizer Bar — 1Rear Suspension Member (for 2wd) — 1Rear Suspension Member (for Awd) — 1Rear Trailing Arm — 1Rear Upper Arm — 1Tire And Wheel System — 1Tire Repair Seal — 1Tire Pressure Warning Receiver — 1Tire Pressure Warning System — 1Tire Pressure Warning Valve — 1Acoustic Vehicle Alerting System — 1Vehicle Approaching Speaker — 1Vehicle Approaching Speaker Ecu — 1Back Door — 1Back Door Closer Ecu — 1Back Door Opener Switch — 1Back Door Support — 1Back Door Weatherstrip — 1Charge Lid Courtesy Switch — 1Charge Lid Opener Motor Assembly — 1Charge Lid Opener System — 1Charge Lid Opener Unit — 1Front Door — 1Front Door Opening Trim Weatherstrip — 1Fuel Lid Opener Motor Assembly — 1Fuel Lid Opener Switch — 1Fuel Lid Opener System — 1Hood — 1Hood Lock Control Cable Assembly — 1Power Back Door Closer Switch — 1Power Back Door Control Switch — 1Power Back Door Drive Unit — 1Power Back Door System — 1Power Back Door Touch Sensor — 1Power Back Door Warning Buzzer — 1Rear Door — 1Rear Door Opening Trim Weatherstrip — 1Reserve Lock Switch — 1Front Bumper — 1Front Door Belt Moulding — 1Front Door Window Frame Moulding — 1Front Fender — 1Front Pillar Upper Cover — 1Grille Shutter — 1Grille Shutter System — 1Name Plate — 1Quarter Garnish — 1Rear Bumper — 1Rear Door Belt Moulding — 1Rear Door Window Frame Moulding — 1Rear Wheel House Plate — 1Rocker Panel Moulding — 1Roof Drip Side Finish Moulding — 1Roof Garnish — 1Wheel Opening Moulding (for Front Side) — 1Wheel Opening Moulding (for Rear Side) — 1Windshield Outside Moulding — 1Horn — 1Horn System — 1Relay — 1Automatic Light Control Sensor — 1Back-up Light Assembly — 1Charge Lid Light — 1Front Marker Light — 1Hazard Warning Switch — 1Headlight Assembly — 1Headlight Dimmer Switch — 1Headlight Leveling Switch — 1High Mounted Stop Light Assembly — 1Illumination Light Assembly — 1License Plate Light Assembly — 1Lighting System — 1Rear Combination Light Assembly — 1Rear Light Assembly — 1Rear Side Marker Light Assembly — 1Relay — 1Side Turn Signal Light Assembly — 1Stop Light Switch — 1Switch Housing — 1Outer Mirror Switch — 1Outer Rear View Mirror — 1Outer Rear View Mirror Cover — 1Outer Rear View Mirror Glass — 1Power Mirror Control System — 1Back Door Glass — 1Front Passenger Side Power Window Switch — 1Power Window Control System — 1Power Window Master Switch — 1Power Window Regulator Motor (for Front Door) — 1Power Window Regulator Motor (for Rear Door) — 1Rear Power Window Switch — 1Relay — 1Roof Window Fix Glass — 1Window Defogger System — 1Windshield Deicer Switch — 1Windshield Deicer System — 1Windshield Glass — 1Front Wiper Motor — 1Rain Sensor — 1Relay — 1Washer Motor — 1Washer Nozzle (for Front Side) — 1Washer Nozzle (for Rear Television Camera) — 1Wiper And Washer System — 1Wiper Ecu — 1Wiper Switch — 1Back Door Lock — 1Door Control Receiver — 1Door Control Switch — 1Door Control Transmitter — 1Door Lock Release Motor (for Rear Side) — 1Door Outside Handle (for Rear Side) — 1Front Door Lock — 1Power Door Lock Control System — 1Rear Door Lock — 1Transmitter Battery — 1Wireless Door Lock Control System — 1Accumulator — 1Air Conditioning Amplifier — 1Air Conditioning Panel — 1Air Conditioning Pressure Sensor — 1Air Conditioning Unit — 1Ambient Temperature Sensor — 1Blower Unit — 1Condenser (for Hev Model) — 1Condenser (for Phev Model) — 1Discharge Temperature Sensor — 1Electric Expansion Valve (cooling) — 1Electric Expansion Valve (heating) — 1Evaporator Pipe Temperature Sensor — 1Evaporator Pressure Regulator — 1Front Blower Motor — 1Front Evaporator Front Solenoid Valve — 1Air Conditioning System (for Hev Model) — 1Front Evaporator Temperature Sensor — 1Heat Exchanger Temperature Sensor — 1Heat Pump Ecu — 1High Pressure Magnetic Valve — 1Humidity Sensor — 1Internal Condenser Temperature Sensor — 1Low Pressure Magnetic Valve — 1Refrigerant (for Hfc-134a(r134a)) — 1Refrigerant Line (for Hev Model) — 1Refrigerant Line (for Phev Model) — 1Relay — 1Room Temperature Sensor — 1Solar Sensor — 1Floor Carpet — 1Front Console Box — 1Instrument Panel Safety Pad — 1Roof Headlining — 1Roof Sunshade — 1Ambient Light (for Driver Side) — 1Ambient Light (for Front Passenger Side) — 1Back Door Courtesy Switch — 1Footwell Light — 1Glove Box Light — 1Lighting System — 1Luggage Compartment Room Light — 1Personal Light — 1Room Light — 1Vanity Light — 1Vanity Light Switch — 1Combination Meter — 1Meter / Gauge System — 1Trip Switch — 1Digital Inner Mirror — 1Digital Rear-view Mirror System — 1Inner Mirror Monitor Camera — 1Inner Rear View Mirror (w/o Ec Mirror) — 1Accessory Power Outlet System — 1Power Outlet Socket (for Console Box Front Side) — 1Power Outlet Socket (for Console Box Rear Side) — 1Power Outlet Socket (for Console Box) — 1Power Outlet Socket (for Luggage Compartment) — 1Power Outlet Switch — 1Wireless Charger Assembly — 1Wireless Charging System — 1Climate Control Seat System — 1Front Power Seat Control System (w/ Memory) — 1Front Power Seat Motor Assembly — 1Front Seat Assembly (for Power Seat) — 1Front Seat Cushion Heater (for Power Seat) — 1Front Seatback Heater (for Power Seat) — 1Lumbar Support Adjuster Assembly — 1Power Seat Control Ecu — 1Power Seat Switch — 1Power Seat Track Rail Assembly — 1Rear Seat Assembly — 1Rear Seat Cushion Heater — 1Rear Seat Reminder System — 1Rear Seatback Heater — 1Seat Heater Control — 1Seat Heater Switch (for Front Seat) — 1Seat Heater Switch (for Rear Side) — 1Seat Heater System — 1Seat Memory Switch — 1Child Restraint Seat Anchor Bracket — 1Front Seat Inner Belt Assembly — 1Front Seat Outer Belt Assembly — 1Occupant Detection Sensor (for Front Passenger Side) — 1Rear Center Seat Outer Belt Assembly — 1Rear Seat Inner Belt Assembly (for Rh Side) — 1Rear Seat Outer Belt Assembly — 1Seat Belt Warning System (w/ Occupant Classification System) — 1Tongue Plate Stopper — 1Airbag System — 1Center Airbag Sensor Assembly — 1Curtain Shield Airbag Assembly — 1Front Airbag Sensor — 1Front Passenger Airbag Assembly — 1Front Seat Side Airbag Assembly — 1Inspection After Collision — 1Knee Airbag Assembly — 1Occupant Classification System — 1Rear Seat Side Airbag Assembly — 1Side Airbag Sensor (for Center Pillar) — 1Side Airbag Sensor (for Front Door) — 1Spiral Cable — 1Steering Pad — 1Certification Ecu — 1Digital Key Ecu — 1Digital Key Receiver (for Front Floor) — 1Digital Key Receiver (for Outside Luggage Compartment) — 1Digital Key Receiver (for Rear Door) — 1Digital Key System — 1Electrical Key Oscillator (for Front Floor) — 1Electrical Key Oscillator (for Outside Luggage Compartment) — 1Electrical Key Oscillator (for Rear Floor) — 1Engine Hood Courtesy Switch — 1Id Code Box — 1Smart Key System (for Start Function) — 1
2steps
~12min
2/5difficulty
Done 0 of 2
  • Precaution
  • Parts Location
  • System Diagram
  • System Description
  • How To Proceed With Troubleshooting
  • Registration
  • Terminals Of Ecu
  • Dtc Check / Clear
  • Data List / Active Test
  • Diagnostic Trouble Code Chart
  • On-vehicle Inspection
  • Lost Communication with TCM Missing Message (U010187,U014087,U029387)

Precaution

PRECAUTION

PRECAUTIONS FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

Parts Location

PARTS LOCATION

ILLUSTRATION

*1

INNER REAR VIEW MIRROR ASSEMBLY

- GARAGE DOOR OPENER

-

-

ILLUSTRATION

*1

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*2

HYBRID Toyota Prius Vehicle CONTROL ECU

*3

DLC3

-

-

System Diagram

SYSTEM DIAGRAM

System Description

SYSTEM DESCRIPTION

DESCRIPTION

(a) A maximum of 3 kinds of transmitter code based systems (example: garage doors, gates and entry gates) can be registered with the vehicle garage door opener. After registration, the vehicle garage door opener can mimic the signal of the transmitter systems and the original transmitters of each transmitter system are not needed.

How To Proceed With Troubleshooting

HINT:

  • Use the following procedure to troubleshoot the garage door opener system.
  • *: Use the GTS.

PROCEDURE

  1. Toyota Prius Vehicle BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

(a) Interview the customer to confirm the problem.

Click here

NEXT
  1. INSPECT BATTERY VOLTAGE

(a) Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V

HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT
  1. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. CHECK FOR DTC*

(a) Clear for DTCs.

Body Electrical > Digital Rear-View Mirror > Clear DTCs

(b) Check for DTCs.

Body Electrical > Digital Rear-View Mirror > Trouble Codes

Result

Proceed to

DTCs are not output

A

Garage Door Opener system DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Terminals of ECU

Click here

(b) On-Toyota Prius Vehicle Inspection

Click here

NEXT
  1. REPAIR OR REPLACE

NEXT
  1. CONFIRMATION TEST

NEXT

END

Registration

REGISTRATION

PROCEDURE

1. REGISTER TRANSMITTER CODE

HINT:

  • The vehicle garage door opener records transmitter codes for systems such as garage doors, gates, entry gates, door locks, home lighting systems, security systems or other transmitter code based systems.
  • The garage door opener is built into the inner rear view mirror assembly. If replacing the inner rear view mirror assembly, transmitter codes for any systems previously registered in the garage door opener must be re-registered.

(a) Re-registration of codes in the garage door opener system (registration mode).

CAUTION:

Do not perform transmitter code registration for a system if people or objects are near the system. When registering transmitter codes for a system, injury or damage can occur because the system may open, close, unlock or otherwise operate.

NOTICE:

  • Before transmitter code registration, confirm that all the electrical systems (headlight, blower motor, rear defogger, etc.) are turned off and no key is in the Toyota Prius vehicle.
  • The garage door opener cannot be used with systems that:

    (1) Were manufactured before April 1, 1982.

    (2) Do not meet federal safety standards (for example, garage doors without a jam protection function).

HINT:

  • A maximum of 3 transmitter codes can be registered with the garage door opener system. It is possible to register 1 handheld transmitter code (original transmitter) for each of the 3 garage door opener system switches.
  • Disconnecting the Toyota Prius vehicle battery will not clear the transmitter codes registered in the garage door opener system.
  • An attempt to overwrite a previously registered code may fail. In this case, the previously registered transmitter code will not be cleared.
  • To successfully program the garage door opener system, it may be necessary to replace the handheld transmitter battery before programming.
  • If registration is performed when the battery level of the transmitter is low, the transmitted radio waves may be too weak and registration may not complete properly.

(1) Step 1:

Select a garage door opener ("HomeLink") switch for transmitter code registration and check that the ("HomeLink") indicator light flashes.

HINT:

Perform step 3 within 60 seconds of step 1, or the indicator light will stop flashing and programming will not be able to be completed.

*a

("HomeLink") Indicator Light

*b

Garage Door Operation Indicators

*c

("HomeLink") Logo

*d

Garage Door Opener ("HomeLink") Switches

*e

Opening

*f

Closing

(2) Step 2:

Point the remote control transmitter for the device at the inner rear view mirror assembly, 2.5 to 7.5 cm (1.0 to 3.0 in.) from the garage door opener ("HomeLink") switches.

HINT:

Keep the ("HomeLink") indicator light in view while programming.

*a

Handheld Transmitter

*b

Garage Door Opener ("HomeLink") Switches

(3) Step 3:

for USA:

except Entry Gate

Press and hold the handheld transmitter button until the ("HomeLink") indicator light changes from slowly flashing (orange) to rapidly flashing (green) (rolling code) or continuously lit (green) (fixed code), then release the handheld transmitter button.

for Entry Gate

Repeatedly press and release the handheld transmitter button at 2 second intervals until the ("HomeLink") indicator light changes from slowly flashing (orange) to rapidly flashing (green) (rolling code) or continuously lit (green) (fixed code).

for Canada:

Repeatedly press and release the handheld transmitter button at 2 second intervals until the ("HomeLink") indicator light changes from slowly flashing (orange) to rapidly flashing (green) (rolling code) or continuously lit (green) (fixed code).

(4) Step 4:

Test the ("HomeLink") operation by pressing the newly programmed switch and observing the indicator light.

HINT:

  • Device with fixed code: if the indicator light is solid and continuous, programming has been completed and the device should activate when the garage door opener ("HomeLink") switch is pressed and released.
  • Device with rolling code: if the indicator light flashes rapidly, the garage door opener motor (or other device) is equipped with a rolling code. Complete the programming process by firmly pressing and holding the programmed garage door opener ("HomeLink") switch for 2 seconds and then release the handheld transmitter button.
  • If the garage door or other device does not operate, proceed to "Programming a rolling code system".

(5) If the transmitter code registration was successful, the ("HomeLink") indicator light of the garage door opener flashes (green) at a cycle of 10 Hz (rapidly). If no malfunction occurs, release both the garage door opener ("HomeLink") switch and handheld transmitter button.

*A

for USA

*B

except Entry Gate

*A

for USA

*B

for Entry Gate

*A

for Canada

-

-

HINT:

  • If transmitter code registration fails:

    (1) The battery in the handheld transmitter may be weak or needs to be replaced.

    (2) The handheld transmitter and opener device to be registered may not be compatible with the garage door opener.

  • Some transmitter signals stop after 1 to 2 seconds. For these types of transmitters:

    (1) Press and hold one of the garage door opener ("HomeLink") switches.

    (2) Press and release the handheld transmitter button every 2 seconds. Check if the transmitter code was successfully registered.

  • After entering the garage door opener registration mode, transmitter code registration must be completed within 60 seconds. If 60 seconds elapse, the garage door opener will enter low power mode (refer to "Low Power Mode" below).

(6) Repeat the steps above to program another device for any of the remaining garage door opener ("HomeLink") switches.

(b) Clearing transmitter codes in the garage door opener system (clear mode).

HINT:

All 3 registered transmitter codes will be cleared. No option exists for only erasing one transmitter code.

*a

("HomeLink") Indicator Light

*b

Garage Door Opener ("HomeLink") Switch 1

*c

Garage Door Opener ("HomeLink") Switch 3

(1) Press and hold the garage door opener ("HomeLink") switches 1 and 3 for 10 seconds until the ("HomeLink") indicator light changes from continuously lit orange to rapidly flashing green.

(c) Low power mode:

(1) If a garage door opener ("HomeLink") switch is held for 60 seconds or more, the garage door opener will enter low power mode to reduce power consumption. When the garage door opener has entered low power mode, the ("HomeLink") indicator light turns off.

2. ROLLING CODE SYSTEMS

(a) If the handheld transmitter for the opener device (customer's garage door) being programmed uses a rolling code, it may be necessary to "train" the garage door opener device.

HINT:

  • "Train" refers to causing the opener device (customer's ceiling mounted garage door opener) to recognize a non-rolling code.
  • The steps required to "train" an opener device may vary depending on the model, type, age, and manufacturer of the device.

(1) Locate the training button on the opener device.

(2) Press the training button.

(3) Within 30 seconds, press and release the programmed garage door opener ("HomeLink") switch twice. Some opener devices may require the garage door opener ("HomeLink") switch to be pressed 3 times.

HINT:

The Toyota Prius vehicle garage door opener system should now operate the opener device. Opener device refers to a device such as a ceiling mounted garage door opener, which is located at the customer's residence. It is necessary to read the instructions for the customer's opener device, to allow the above procedure to be performed safely and successfully. The customer should be aware that performing this procedure will result in a lowered level of security for the customer's opener device.

*a

Example

*b

Training Button

Terminals Of Ecu

TERMINALS OF ECU

INNER REAR VIEW MIRROR ASSEMBLY (GARAGE DOOR OPENER)

(a) Disconnect the U12 inner rear view mirror assembly connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Terminal Description

Condition

Specified Condition

U12-1 (IG) - Body ground

IG power supply

Ignition switch off

Below 1 V

Ignition switch ON

11 to 14 V

U12-6 ( B) - Body ground

Auxiliary battery power supply

Ignition switch off

11 to 14 V

U12-2 (E) - Body ground

Ground

Always

Below 1 Ω

Dtc Check / Clear

DTC CHECK / CLEAR

ALL READINESS

HINT:

  • With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.
  • You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON

(c) Turn the GTS on.

(d) Clear the DTCs even if no DTCs are stored. Enter the following menus: Body Electrical / Digital Rear-View Mirror / Trouble Codes.

Body Electrical > Digital Rear-View Mirror > Clear DTCs

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON.

(g) Check that the power supply voltage of the inner rear view mirror assembly is 10 V or more, then turn the ignition switch to ON and wait for 20 seconds or more.

(h) Enter the following menus: Body Electrical / Digital Rear-View Mirror / Utility.

Body Electrical > Digital Rear-View Mirror > Utility

All Readiness

(i) Input the DTC to be confirmed.

(j) Check the DTC judgment result.

GTS Display

Description

Normal

  • DTC judgment completed
  • System normal

Abnormal

  • DTC judgment completed
  • System abnormal

Incomplete

  • DTC judgment not completed

N/A

  • Unable to perform DTC judgment
  • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

If the judgment result shows Incomplete or N/A, check that the power supply voltage of the inner rear view mirror assembly is 10 V or more, then turn the ignition switch to ON and wait for 20 seconds or more, then run the DTC judgement.

Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Enter the following menus: Body Electrical / Digital Rear-View Mirror / Data List.

(b) Read the Data List according to the display on the GTS.

Body Electrical > Digital Rear-View Mirror > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Current total driving distance

0 to 999999

Equivalent to the actual total driving distance

-

Total Distance Traveled - Unit

Unit of total distance traveled

km or mile

-

-

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

Garage Door Opener System

DTC No.

Detection Item

DTC Output from

Priority

Link

U010187

Lost Communication with TCM Missing Message

Digital Rear-View Mirror

B

U014087

Lost Communication with Body Control Module Missing Message

Digital Rear-View Mirror

B

U029387

Lost Communication with Hybrid/EV Powertrain Control Module Missing Message

Digital Rear-View Mirror

B

On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. INSPECT GARAGE DOOR OPENER

(a) Press each garage door opener ("HomeLink") switch and check that the ("HomeLink") indicator light turns on. If one or more of the garage door opener ("HomeLink") switches does not turn on the ("HomeLink") indicator light, check the condition of the fuse and wire harness. If the wire of the fuse is broken or the wire harness is malfunctioning repair or replace it. If not, replace the inner rear view mirror assembly (garage door opener).

HINT:

Click here

*a

("HomeLink") Indicator Light

*b

Garage Door Operation Indicators

*c

("HomeLink") Logo

*d

Garage Door Opener ("HomeLink") Switches

*e

Opening

*f

Closing

2. INSPECT GARAGE DOOR OPENER REGISTRATION AND TRANSMITTING

HINT:

Use the "HomeLink" tester and a tester transmitter for this test. First clear the customer transmitter codes, and then register the tester transmitter code.

Click here

(a) Check if the tester transmitter code was successfully registered.

HINT:

  • Any garage door opener ("HomeLink") switch can be pressed.
  • If the code cannot be registered, replace the inner rear view mirror assembly (garage door opener).

    Click here

(b) Apply battery voltage to the "HomeLink" tester as shown in the illustration.

*a

"HomeLink" Tester

*b

Red LED

*c

Press

(c) Press a garage door opener ("HomeLink") switch. Check if the red LED of the "HomeLink" tester illuminates.

HINT:

If the red LED does not illuminate, replace the inner rear view mirror assembly (garage door opener).

Click here

(d) When the inspection is complete, register the customer transmitter code(s) again.

HINT:

  • Registration of the customer transmitter code(s) may not be possible in the service facility if the customer's transmitters are not available or if any of the buttons are used for rolling code-type systems.
  • Refer to the Owner's Manual for additional information about registration (programming) of transmitter codes.

Lost Communication with TCM Missing Message (U010187,U014087,U029387)

DESCRIPTION

  • U010187: The inner rear view mirror assembly receives signals from the hybrid vehicle control ECU via CAN communication.
  • U014087: The inner rear view mirror assembly receives signals from the main body ECU (multiplex network body ECU) via CAN communication.
  • U029387: The inner rear view mirror assembly receives signals from the hybrid Toyota Prius vehicle control ECU via CAN communication.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

U010187

Lost Communication with TCM Missing Message

No communication between inner rear view mirror assembly and hybrid Toyota Prius vehicle control ECU for 10 seconds or more. (1-trip detection logic*)

  • CAN communication system
  • Inner rear view mirror assembly
  • Hybrid vehicle control ECU
  • Wire harness or connector

Digital Rear-View Mirror

B

U014087

Lost Communication with Body Control Module Missing Message

No communication between inner rear view mirror assembly and main body ECU (multiplex network body ECU) for 10 seconds or more. (1-trip detection logic*)

  • CAN communication system
  • Inner rear view mirror assembly
  • Main body ECU (multiplex network body ECU)
  • Wire harness or connector

Digital Rear-View Mirror

B

U029387

Lost Communication with Hybrid/EV Powertrain Control Module Missing Message

No communication between inner rear view mirror assembly and hybrid Toyota Prius vehicle control ECU for 10 seconds or more. (1-trip detection logic*)

  • CAN communication system
  • Inner rear view mirror assembly
  • Hybrid vehicle control ECU
  • Wire harness or connector

Digital Rear-View Mirror

B

  • *: Only detected while a malfunction is present and the ignition switch is ON.
Confirmation procedure

HINT:

After repairs have been completed, clear the DTCs and then check that the Toyota Prius vehicle has returned to normal by performing "All Readiness" using the GTS.

Click here

  1. Check that the power supply voltage of the inner rear view mirror assembly is 10 V or more.
  2. Turn the ignition switch to ON and wait for 20 seconds or more.

PROCEDURE

  1. CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Digital Rear-View Mirror > Clear DTCs
NEXT
  1. CHECK FOR DTC

(a) Check if CAN communication DTCs are output.

Body Electrical > Digital Rear-View Mirror > Trouble Codes

OK:

DTC U010187, U014087 and U029387 are not output

Result

Proceed to

DTCs are not output

A

U010187, U014087 or U029387 is output

B

HINT:

  • If CAN communication system malfunction DTCs are output, they may also be output for other systems.
  • If the CAN communication system has been inspected and repaired in other systems, the DTC will not be output when rechecking for DTCs.
  • If the DTC is output frequently, duplicate the conditions that cause the problem symptoms and perform the check again, even though the DTC was not output when rechecking for DTCs.

    Click here

A

USE SIMULATION METHOD TO CHECK

B

GO TO CAN COMMUNICATION SYSTEM