P0711 Transmission fluid temperature sensor A
DTC Logic
DTC DETECTION LOGIC
| DTC | Trouble diagnosis name | DTC detection condition | Possible causes |
| P0711 | Transmission Fluid Temperature Sensor A Circuit Range/ Performance | Under the following diagnosis conditions, CVT fluid temperature does not rise to 10C (50F) after driving for a certain period of time with the TCM-received fluid temperature sensor value between −40C (−40F) and 9C (48.2F). - Diagnosis condition - Selector lever: "D" position - Vehicle speed: 10 km/h or more - Engine speed: 450 rpm or more - Accelerator pedal position: 1.0/8 or more - TCM power supply voltage: More than 11 V |
CVT fluid temperature sensor |
| When the condition of the final judgment is satisfied after satisfying that of the provisional judgment: - Provisional judgment: All of the following conditions are satisfied within 2 seconds after the ignition switch is turned ON. - U0073, U0100, P0712 and P0713 are not detected. - CAN communication is normal. - TCM power supply voltage: More than 11 V - The difference between CVT fluid temperature and engine coolant temperature is 37C (98.6F) or more, or −27C (−16.6F) or less. - Final judgment: When all of the following conditions are satisfied and this state is maintained for 300 seconds: - ECM is normal. - Provisional judgment is satisfied. |
CVT fluid temperature sensor |
DTC CONFIRMATION PROCEDURE
CAUTION: Always drive vehicle at a safe speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK CVT FLUID TEMPERATURE SENSOR FUNCTION
With CONSULT
- Cool the engine.
- Turn ignition switch ON. CAUTION: Never start the engine.
- Select "FLUID TEMP" in "Data Monitor" in "TRANSMISSION".
- Select "COOLANT TEMP/S" in "Data Monitor" in "ENGINE".
- Check temperature difference between CVT fluid and engine coolant.
With GST
- Complete engine diagnoses P0111, P0116, and P0196.
- After starting the engine start, run the engine at idle for 5 minutes.
- Check the DTC.
Is the temperature calculated by subtracting engine coolant temperature from CVT fluid temperature more than 37C (98.6F) or is it less than −27C (−16.6F)? (With CONSULT)/Is "P0711" detected? (With GST)
YES >> Go to TM "Diagnosis Procedure".
NO-1 [With CONSULT: "FLUID TEMP" is 10C (50F) or more]>>INSPECTION END
NO-2 [With CONSULT: "FLUID TEMP" is 9C (48.2F) or less]>>GO TO 3.
NO-3 (With GST)>>GO TO 3.
3.CHECK DTC DETECTION
With CONSULT
- Select "SLCT LVR POSI", "VSP SENSOR", "ACCELE POSI SEN 1", "FLUID TEMP" in "Data Monitor" in "TRANSMISSION".
- Record CVT fluid temperature.
- Start the engine and wait for at least 3 minutes.
- Drive the vehicle for the total minuets specified in the Driving time column below with the following conditions satisfied.
SLCT LVR POSI : D VSP SENSOR : 10 km/h or more ACCELE POSI SEN 1 : 1.0/8 or more

5. Perform "Self Diagnostic Results" in "TRANSMISSION".
With GST
1. Cool the engine.
2. Start the engine and wait for at least 3 minutes.
3. Drive the vehicle and maintain the following conditions for 21 minutes or more.
Selector lever : D position Vehicle speed : 10 km/h or more Accelerator pedal opening : 1.0/8 or more
4. Check the DTC.
Is "P0711" detected?
YES >> Go to TM "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK CVT FLUID TEMPERATURE SENSOR
- Turn ignition switch OFF.
- Disconnect CVT unit connector.
- Check CVT fluid temperature sensor. Refer to TM "Component Inspection (CVT Fluid Temperature Sensor)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI "Intermittent Incident".
NO >> Repair or replace malfunctioning parts.
Component Inspection (CVT Fluid Temperature Sensor)
1.CHECK CVT FLUID TEMPERATURE SENSOR
Check resistance between CVT unit connector terminals. 
Is the inspection result normal?
YES >> INSPECTION END
NO >> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to TM "Removal and Installation".