Power supply and ground circuit
Diagnosis Procedure
1.CHECK GROUND CONNECTION
- Turn ignition switch OFF.
- Check ground connection E. Refer to Ground Inspection in GI, "Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT
- Disconnect ECM harness connectors.
- Check the continuity between ECM harness connector and ground.
| ECM | Ground | Continuity | |
| Connector | Terminal | ||
| F10 | 10 | Ground | Existed |
| 11 | |||
| E16 | 108 | ||
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E55, F55
- Harness for open or short between ECM and ground
>> Repair open circuit or short to power in harness or connectors.
4.CHECK ECM POWER SUPPLY CIRCUITI
- Reconnect ECM harness connectors.
- Turn ignition switch ON.
- Check the voltage between ECM harness connector and ground.
| ECM | Ground | Voltage | |
| Connector | Terminal | ||
| F16 | 93 | Ground | Battery voltage |
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following.
- 10 A fuse (No. 55)
- Harness for open or short between ECM and fuse
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK ECM POWER SUPPLY CIRCUITII
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON and then OFF.
| ECM | Ground | Voltage | |
| Connector | Terminal | ||
| F16 | 106 | Ground | After turning ignition switch OFF, battery voltage will exist for a few seconds, then drop to approximately 0 V. |
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 9.
7.CHECK ECM POWER SUPPLY CIRCUITIII
- Turn ignition switch ON.
- Check the voltage between IPDM E/R harness connector and ground.
| IPDM E/R | Ground | Voltage | |
| Connector | Terminal | ||
| F43 | 50 | Ground | Battery voltage |
Is the inspection result normal?
YES >> GO TO 8.
NO >> Replace IPDM E/R. Refer to PCS, "Removal and Installation" (WITH IKEY) or PCS, "Removal and Installation" (WITHOUT IKEY).
8.CHECK INTERMITTENT INCIDENT
Refer to GI, "Intermittent Incident".
>> INSPECTION END
9.CHECK ECM POWER SUPPLY CIRCUITIV
- Turn ignition switch OFF and wait at least 10 seconds.
- Check the voltage between ECM harness connector and ground.
| ECM | Ground | Voltage | |
| Connector | Terminal | ||
| F10 | 32 | Ground | Battery voltage |
Is the inspection result normal?
YES >> GO TO 13.
NO >> GO TO 10.
10.CHECK ECM POWER SUPPLY CIRCUITV
- Disconnect ECM harness connector.
- Disconnect IPDM E/R harness connector F.
- Check the continuity between ECM harness connector and IPDM E/R harness connector.
| ECM | IPDM E/R | Continuity | ||
| Connector | Terminal | Connector | Terminal | |
| F10 | 32 | F43 | 50 | Existed |
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 12.
NO >> GO TO 11.
11.DETECT MALFUNCTIONING PART
Check the following.
- Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
12.CHECK 20 A FUSE
- Disconnect 20 A fuse (No. 53) from IPDM E/R.
- Check 20 A fuse.
Is the inspection result normal?
YES >> GO TO 14.
NO >> Replace 20 A fuse.
13.CHECK ECM POWER SUPPLY CIRCUITVI
- Disconnect ECM harness connector.
- Disconnect IPDM E/R harness connector E44.
- Check the continuity between ECM harness connector and IPDM E/R harness connector.
| ECM | IPDM E/R | Continuity | ||
| Connector | Terminal | Connector | Terminal | |
| F16 | 105 | F44 | 11 | Existed |
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 14.
NO >> Repair open circuit or short to ground or short power in harness or connectors.
14.CHECK INTERMITTENT INCIDENT
Refer to GI, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS, "Removal and Installation" (WITH IKEY) or PCS, "Removal and Installation" (WITHOUT IKEY).
NO >> Repair or replace harness or connectors.