Camshaft

In this manual: Camshaft
Precautions — 1Preparation — 1Camshaft valve clearance — 1Compression pressure — 1Noise, vibration and harshness (NVH) troubleshooting — 1Drive belt — 1Air cleaner filter — 1Spark plug — 1Drive belt idler pulley — 1Air cleaner and air duct — 1Intake manifold — 1Exhaust manifold — 1Oil pan (lower) — 1Fuel injector and fuel tube — 1Ignition coil, spark plug and rocker cover — 1Timing chain — 1Camshaft — 1Valve oil seal — 1Front oil seal — 1Rear oil seal — 1Cylinder head — 1Engine assembly — 1Engine stand setting — 1Oil pan (upper) and oil strainer — 1Cylinder block — 1How to select piston and bearing — 1Service data and specifications (sds) — 1Precautions — 1Preparation — 1Engine oil — 1Oil filter — 1Oil pump — 1Oil cooler — 1Service data and specifications (SDS) — 1Precaution — 1Description — 1Engine coolant — 1Radiator — 1Cooling fan — 1Water pump — 1Thermostat — 1Water outlet — 1Precaution — 1Engine control system — 1Structure and operation — 1Engine control system — 1Multiport fuel injection system — 1Electric ignition system — 1Air conditioning cut control — 1Cooling fan control — 1Evaporative emission system — 1Intake valve timing control — 1Exhaust valve timing control — 1Engine protection control at low engine oil pressure — 1Fuel filler cap warning system — 1Automatic speed control device (ASCD) — 1Automatic speed control device (ASCD) — 1Diagnosis description — 1Ecm — 1Diagnosis and repair workflow — 1Additional service when replacing ECM — 1Accelerator pedal released position learning — 1Throttle valve closed position learning — 1Idle air volume learning — 1Mixture ratio selflearning value clear — 1Basic inspection — 1Fuel pressure check — 1How to set SRT code — 1How to erase permanent DTC — 1Trouble diagnosis specification value — 1Power supply and ground circuit — 1U0101 can comm circuit — 1U1001 CAN comm circuit — 1P0011 IVT control — 1P0014 EVT control — 1P0031, P0032 A/F sensor 1 heater — 1P0037, P0038 HO2s2 heater — 1P0075 IVT control solenoid valve — 1P0078 EVT control solenoid valve — 1P0101 MAF sensor — 1P0102, P0103 MAF sensor — 1P0111 IAT sensor — 1P0112, P0113 IAT sensor — 1P0116 ECT sensor — 1P0117, P0118 ECT sensor — 1P0122, P0123 TP sensor — 1P0125 ECT sensor — 1P0127 IAT sensor — 1P0128 thermostat function — 1P0130 A/F sensor 1 — 1P0131 A/F sensor 1 — 1P0132 A/F sensor 1 — 1P0137 HO2s2 — 1P0138 HO2s2 — 1P0139 HO2s2 — 1P014C, P014D, P015A, P015B, A/F sensor 1 — 1P0171 fuel injection system function — 1P0181 FTT sensor — 1P0182, P0183 FTT sensor — 1P0196 EOT sensor — 1P0197, P0198 EOT sensor — 1P0222, P0223 TP sensor — 1P0300, P0301, P0302, P0303, P0304 misfire — 1P0327, P0328 KS — 1P0335 CKP sensor (POC) — 1P0340 CMP sensor (PHASE) — 1P0420 three way catalyst function — 1P0441 EVAP control system — 1P0443 EVAP canister purge volume control solenoid valve — 1P0444, P0445 EVAP canister purge volume control solenoid valve — 1P0447 EVAP canister vent control valve — 1P0448 EVAP canister vent control valve — 1P0451 EVAP control system pressure sensor — 1P0452 EVAP control system pressure sensor — 1P0453 EVAP control system pressure sensor — 1P0456 EVAP control system — 1P0460 fuel level sensor — 1P0461 fuel level sensor — 1P0462, P0463 fuel level sensor — 1P0500 VSS — 1P0506 ISC system — 1P0507 ISC system — 1P050a, P050b, P050e cold start control — 1P0520 EOP sensor — 1P0524 engine oil pressure — 1P0603 ECM power supply — 1P0605 ECM — 1P0607 ECM — 1P0643 sensor power supply — 1P0850 PNP switch — 1P1078 EVT control position sensor — 1P1148 closed loop control — 1P117A air fuel ratio — 1P1212 TCS communication line — 1P1217 engine over temperature — 1P1225 TP sensor — 1P1226 TP sensor — 1P1550 battery current sensor — 1P1551, P1552 battery current sensor — 1P1553 battery current sensor — 1P1554 battery current sensor — 1P1564 ASCD steering switch — 1P1572 ASCD brake switch — 1P1574 ASCD vehicle speed sensor — 1P1715 Input speed sensor — 1P1720 VSS — 1P1805 brake switch — 1P2096, P2097 A/F sensor 1 — 1P2100, P2103 throttle control motor relay — 1P2101 electric throttle control function — 1P2118 throttle control motor — 1P2119 electric throttle control actuator — 1P2122, P2123 APP sensor — 1P2127, P2128 APP sensor — 1P2135 TP sensor — 1P2138 APP sensor — 1Brake pedal position switch — 1Clutch pedal position switch — 1Cooling fan — 1Electrical load signal — 1Fuel injector — 1Fuel pump — 1Ignition signal — 1Malfunction indicator lamp — 1On board refueling vapor recovery (ORVR) — 1Refrigerant pressure sensor — 1Engine control system symptoms — 1Normal operating condition — 1IDLE SPEED — 1Ignition timing — 1Evaporative emission system — 1EVAP leak check — 1Positive crankcase ventilation — 1Removal and installation — 1Service data and specifications (SDS) — 1Precautions — 1Fuel level sensor unit, fuel filter and fuel pump assembly — 1Fuel tank — 1EVAP canister — 1EVAP canister filter — 1EVAP canister vent control valve — 1EVAP control system pressure sensor — 1Fuel level sensor unit — 1Precautions — 1Exhaust system — 1Precautions — 1Diagnosis and repair workflow — 1B terminal circuit — 1S connector circuit — 1Starter motor — 1Precautions — 1Accelerator control system — 1Precautions — 1Clutch pedal — 1Clutch fluid — 1Clutch pedal — 1Clutch master cylinder — 1Clutch piping — 1CSC (Concentric slave cylinder) — 1Clutch disc and clutch cover — 1Service data and specifications (SDS) — 1Precautions — 1Structure and operation — 1Position switch — 1Gear oil — 1Side oil seal — 1Position switch — 1Control linkage — 1Air breather hose — 15Th main gear assembly — 1Transaxle assembly — 1Transaxle assembly — 1Input shaft and gear — 1Mainshaft and gear — 1Final drive — 1Precautions — 1A/T Control system — 1A/T Shift lock system — 1Transaxle — 1A/T control system — 1Line pressure control — 1Shift change control — 1Lock-up control — 1Diagnosis description — 1Consult function — 1TCM — 1Diagnosis and repair work flow — 1Additional service when replacing TCM — 1Additional service when replacing transaxle assembly — 1A/T Fluid cooler — 1Stall test — 1Line pressure test — 1U0073 Communication bus a off — 1U0100 Lost communication (ECM A) — 1U0140 Lost communication (BCM) — 1U0155 Lost communication (IPC) — 1U0300 Can communication data — 1U1000 Can comm circuit — 1U1117 Lost communication (ABS) — 1P062F EEPROM — 1P0705 Transmission range switch A — 1P0706 Transmission range sensor A — 1P0711 Transmission fluid temperature sensor A — 1P0712 Transmission fluid temperature sensor A — 1P0713 Transmission fluid temperature sensor A — 1P0717 Input speed sensor A — 1P0720 Output speed sensor — 1P072C Stuck in 1GR — 1P072D Stuck in 2GR — 1P072E Stuck in 3GR — 1P072F Stuck in 4GR — 1P0731 1GR Incorrect ratio — 1P0732 2GR Incorrect ratio — 1P0733 3GR Incorrect ratio — 1P0734 4GR Incorrect ratio — 1P073E Unable to engage r range — 1P073F Unable to engage 1GR — 1P0740 Torque converter — 1P0743 Torque converter — 1P0744 Torque converter — 1P074A Unable to engage 2GR — 1P074B Unable to engage 3GR — 1P074C Unable to engage 4GR — 1P0863 TCM Communication — 1P0890 TCM — 1P0962 Pressure control solenoid A — 1P0963 Pressure control solenoid A — 1P0973 Shift solenoid A — 1P0974 Shift solenoid A — 1P0976 Shift solenoid B — 1P0977 Shift solenoid B — 1P0979 Shift solenoid C — 1P0980 Shift solenoid C — 1P0982 Shift solenoid D — 1P0983 Shift solenoid D — 1P2760 Torque converter — 1Main power supply and ground circuit — 1Overdrive control switch — 1O/D OFF indicator lamp — 1Shift position indicator circuit — 1Shift lock system — 1A/T Fluid — 1A/T Shift selector — 1Control cable — 1Key interlock cable — 1TCM — 1Oil pan — 1Output speed sensor — 1Differential side oil seal — 1Fluid cooler tube — 1Transmission assembly — 1Service data and specifications (SDS) — 1Precautions — 1Component parts — 1Shift lock system — 1Structure and operation — 1Fluid cooler & fluid warmer system — 1CVT Control system — 1Line pressure control — 1Shift control — 1Lock-up control — 1Idle neutral control — 1Diagnosis system (TCM) — 1TCM — 1Diagnosis and repair work flow — 1Additional service when replacing TCM — 1Additional service when replacing transaxle assembly — 1Calibration of G Sensor — 1CVT Fluid cooler system — 1Stall test — 1Line pressure test — 1U0073 Communication bus A off — 1U0100 Lost communication (ECM A) — 1U0140 Lost communication (BCM) — 1U0141 Lost communication (BCM A) — 1U0155 Lost communication (IPC) — 1U0300 Can communication data — 1U1000 Can COMM circuit — 1U1117 Lost communication (ABS) — 1P062F EEPROM — 1P0705 Transmission range sensor A — 1P0706 Transmission range sensor A — 1P0711 Transmission fluid temperature sensor A — 1P0712 Transmission fluid temperature sensor A — 1P0713 Transmission fluid temperature sensor A — 1P0715 Input speed sensor A — 1P0720 Output speed sensor — 1P0740 Torque converter — 1P0743 Torque converter — 1P0744 Torque converter — 1P0746 Pressure control solenoid A — 1P0846 Transmission fluid pressure SEN/SW B — 1P0847 Transmission fluid pressure SEN/SW B — 1P0848 Transmission fluid pressure SEN/SW B — 1P0863 TCM Communication — 1P0890 TCM — 1P0962 Pressure control solenoid A — 1P0963 Pressure control solenoid A — 1P0965 Pressure control solenoid B — 1P0966 Pressure control solenoid B — 1P0967 Pressure control solenoid B — 1P0998 Shift solenoid F — 1P0999 Shift solenoid F — 1P099B Shift solenoid G — 1P099C Shift solenoid G — 1P1586 G Sensor — 1P1588 G Sensor — 1P2765 Clutch B speed sensor — 1P2857 Clutch A pressure — 1P2858 Clutch B pressure — 1P2859 Clutch A pressure — 1P285A Clutch B pressure — 1Main power supply and ground circuit — 1Overdrive control switch — 1OD OFF indicator lamp — 1Shift position indicator circuit — 1Shift lock system — 1CVT Control system — 1CVT Fluid — 1CVT Shift selector — 1Control cable — 1Key interlock cable — 1TCM — 1Air breather hose — 1G Sensor — 1Oil pan — 1Primary speed sensor — 1Secondary speed sensor — 1Output speed sensor — 1Differential side oil seal — 1Water hose — 1Fluid cooler hose — 1PLUG — 1Transmission assembly — 1Service data and specifications (SDS) — 1Precautions — 1Front wheel hub and knuckle — 1Front wheel hub and knuckle — 1Front drive shaft — 1Front drive shaft — 1Precautions — 1Front suspension assembly — 1Front coil spring and strut — 1Transverse link — 1Front stabilizer — 1Front suspension member — 1Precautions — 1Wheel alignment — 1Rear shock absorber — 1Coil spring — 1Rear suspension beam — 1PRECAUTIONS — 1Component parts — 1Tire pressure monitoring system — 1Air pressure monitor — 1Air pressure monitor — 1Diagnosis and repair work flow — 1Transmitter wake up operation — 1Id registration procedure — 1C1704, C1705, C1706, C1707 Low tire pressure — 1C1708, C1709, C1710, C1711 Transmitter (no data) — 1C1716, C1717, C1718, C1719 Transmitter (pressure data) — 1C1729 Vehicle speed signal — 1Low tire pressure warning lamp — 1Power supply and ground circuit — 1Low tire pressure warning lamp does not turn on — 1Low tire pressure warning lamp does not turn off — 1Low tire pressure warning lamp blinks — 1Road wheel — 1Road wheel tire assembly — 1Transmitter — 1Precautions — 1Brake pedal — 1Brake fluid — 1Brake pad — 1Disc rotor — 1Brake lining — 1Brake drum — 1Brake pedal — 1Front — 1Rear — 1Brake master cylinder — 1Brake booster and check valve — 1Vacuum lines — 1Brake pad — 1Brake caliper assembly — 1Rear drum brake — 1Precautions — 1Parking brake system — 1Parking brake control — 1Precautions — 1Component parts — 1VDC/TCS/ABS — 1Diagnosis system [abs actuator and electric unit (control unit)] — 1ABS Actuator and electric unit (control unit) — 1Diagnosis and repair work flow — 1Adjustment of steering angle sensor neutral position — 1C1101, C1102, C1103, C1104 Wheel sensor — 1C1105, C1106, C1107, C1108 Wheel sensor — 1C1109 Power and ground system — 1C1110, C1153, C1170 ABS Actuator and electric unit (control unit) — 1C1111 Pump motor — 1C1115 ABS Sensor [abnormal signal] — 1C1116 Stop lamp switch — 1C1120, C1122, C1124, C1126 ABS In valve system — 1C1121, C1123, C1125, C1127 ABS Out valve system — 1C1130 Engine signal — 1C1140 Actuator relay system — 1C1142 Press sensor — 1C1143 Steering angle sensor — 1C1144 Incomplete steering angle sensor adjustment — 1C1145, C1146 Yaw rate/side/decel g sensor — 1C1155 BR Fluid level low — 1C1164, C1165, C1166, C1167 CV/SV System — 1U1000 CAN Comm circuit — 1U1002 System comm (CAN) — 1Parking brake switch — 1VDC OFF Switch — 1ABS Warning lamp — 1Brake warning lamp — 1VDC OFF Indicator lamp — 1Slip indicator lamp — 1VDC/TCS/ABS — 1Excessive ABS Function operation frequency — 1Unexpected pedal reaction — 1The braking distance is long — 1Pedal vibration or ABS operation sound occurs — 1Vehicle jerks during VDC/TCS/ABS control — 1Wheel sensor — 1Sensor rotor — 1ABS Actuator and electric unit (control unit) — 1Precautions — 1Steering wheel — 1Steering wheel — 1Steering column — 1Steering shaft — 1Steering gear and linkage — 1Steering gear and linkage — 1Precautions — 1EPS System — 1Diagnosis system (EPS control unit) — 1EPS control unit — 1Diagnosis and repair workflow — 1C1601 Battery power supply — 1C1604 Torque sensor — 1C1606 EPS Motor — 1C1607, C1608 EPS Control unit — 1C1609 Vehicle speed signal — 1C1610 Engine status signal — 1U1000 CAN Comm circuit — 1EPS Warning lamp — 1EPS Warning lamp does not turn OFF — 1Steering wheel turning force is heavy or light — 1Unbalance steering wheel turning force and return between right and left — 1Unbalance steering wheel turning force (torque variation) — 1EPS Control unit — 1Precautions — 1Component inspection — 1Seat belt retractor — 1Precautions — 1Collision diagnosis — 1Driver air bag module — 1Spiral cable — 1Passenger air bag module — 1Side curtain air bag module — 1Side air bag module — 1Crash zone sensor — 1Side air bag (satellite) sensor — 1Diagnosis sensor unit — 1Precautions — 1Component parts — 1SRS Air bag system — 1Occupant classification system — 1Seat belt warning lamp system — 1Diagnosis system (air bag) — 1Diagnosis sensor unit — 1Diagnosis and repair work flow — 1Inspection and adjustment — 1B1049 - B1052, B1054 - B1057 Driver airbag module — 1B1065 - B1068, B1070 - B1073 Passenger airbag module — 1B1134 - B1137 Side airbag module LH — 1B1129 - B1132 Side airbag module RH — 1B1150 - B1153 Side curtain air bag module LH — 1B1145 - B1148 Side curtain air bag module RH — 1B1086 - B1089 Seat belt pre-tensioner LH — 1B1081 - B1084 Seat belt pre-tensioner RH — 1B1033 - B1035 Crash zone sensor — 1B1118 - B1120 Satellite sensor LH — 1B1113 - B1115 Satellite sensor RH — 1B1343 - B1349 Front door satellite sensor LH — 1B1336 - B1342 Front door satellite sensor RH — 1B1350 Front door satellite sensors — 1B1XXX Air bag diagnosis sensor unit — 1B1023 Passenger air bag off indicator — 1B1017, B1018, B1020, B1021, B1022, B1025, B1032, B1048 OCS System — 1B1209 - B1210 Collision detection — 1SRS Air bag warning lamp does not turn on — 1SRS Air bag warning lamp does not turn off — 1Seat belt warning system — 1Precautions — 1Blower motor — 1Precautions — 1Preparation — 1Component parts — 1Refrigeration system — 1Diagnosis and repair workflow — 1Refrigerant — 1Oil — 1Performance test — 1Compressor — 1Condenser — 1Low-pressure flexible hose — 1High-pressure flexible hose — 1High-pressure pipe — 1Expansion valve — 1Refrigerant pressure sensor — 1A/C Unit assembly — 1Evaporator — 1Precautions — 1Manual air conditioning system — 1Diagnosis and repair workflow — 1Operation inspection — 1A/C On signal — 1Blower fan on signal — 1A/C Indicator — 1Front blower motor — 1Magnet clutch — 1Insufficient cooling — 1Insufficient heating — 1Compressor does not operate — 1Front air control — 1Refrigerant pressure sensor — 1Blower fan resistor — 1Intake door cable — 1Mode door cable — 1Air mix door cable — 1Precautions — 1Squeak and rattle trouble diagnoses — 1Front door finisher — 1Rear door finisher — 1Front pillar finisher — 1Kicking plate inner — 1Dash side finisher — 1Body side welt — 1Center pillar upper finisher — 1Rear pillar finisher — 1Rear parcel shelf finisher — 1Floor trim — 1Headlining — 1Trunk rear plate — 1Trunk lid trim — 1Precautions — 1Squeak and rattle trouble diagnoses — 1Instrument panel assembly — 1Steering column covers — 1Cluster lid A — 1Instrument lower panel LH — 1Glove box assembly and housing — 1Center console assembly — 1Center console lower — 1Center console assembly — 1Precautions — 1Squeak and rattle trouble diagnoses — 1Front seat — 1Passenger side — 1Rear seat — 1Front seat — 1Passenger side — 1Rear seat — 1Door & lock (DLK) — 1Precautions — 1Component parts — 1System (power door lock system) — 1Intelligent key system — 1Door lock function — 1Trunk open function — 1Remote keyless entry function — 1Key reminder function — 1Warning function — 1Diagnosis and repair work flow — 1Inspection and adjustment — 1B2621 Inside antenna — 1B2622 Inside antenna — 1B2623 Inside antenna — 1B2626 Outside antenna — 1B2627 Outside antenna — 1B2628 Outside antenna — 1Power supply and ground circuit — 1Combination meter buzzer — 1Door lock actuator — 1Rear LH — 1Rear RH — 1Door lock and unlock switch — 1Door request switch — 1Door switch — 1Hazard function — 1Intelligent key — 1Key warning lamp — 1Remote keyless entry receiver — 1Shift P Warning lamp — 1Trunk lid opener actuator — 1Trunk lid opener switch — 1Trunk lamp switch — 1Door does not lock/unlock with door lock and unlock switch — 1Door does not lock/unlock with driver side door lock knob or door key cylinder — 1Door does not lock/unlock with door request switch — 1Door does not lock/unlock with intelligent key — 1Trunk lid does not open — 1Ignition position warning function does not operate — 1Auto door lock operation does not operate — 1Vehicle speed sensing auto lock operation does not operate — 1IGN OFF Interlock door unlock function does not operate — 1Hazard and buzzer reminder does not operate — 1Key reminder function does not operate — 1OFF Position warning does not operate — 1P Position warning does not operate — 1ACC Warning does not operate — 1Take away warning does not operate — 1Intelligent key low battery warning does not operate — 1Door lock operation warning does not operate — 1Key id warning does not operate — 1Panic alarm function does not operate — 1Squeak and rattle trouble diagnoses — 1Hood assembly — 1Hood hinge — 1Radiator core support upper — 1Radiator core support lower — 1Front fender — 1Fender cover — 1Door assembly — 1Door hinge — 1Door check link — 1Door assembly — 1Door hinge — 1Door check link — 1Trunk lid assembly — 1Trunk lid striker — 1Trunk lid hinge — 1Torsion bar — 1Trunk lid weather-strip — 1Hood lock — 1Hood lock control cable — 1Hood lock secondary control — 1Door lock — 1Inside handle — 1Outside handle — 1Door lock — 1Inside handle — 1Outside handle — 1Trunk lid lock — 1Trunk lid opener handle — 1Trunk lid opener cable — 1Fuel filler opener cable — 1Fuel filler lid lock — 1Door switch — 1Inside key antenna — 1Outside key antenna — 1Intelligent key battery — 1Precautions — 1Component parts — 1Automatic door lock/unlock function — 1Power door lock system — 1Remote keyless entry system — 1Trunk lid opener system — 1Diagnosis system (BCM) — 1Diagnosis and repair workflow — 1U1000 CAN COMM — 1Power supply and ground circuit — 1Door switch — 1Door lock and unlock switch — 1Key cylinder switch — 1Key switch (BCM Input) — 1Door lock actuator — 1Trunk lid opener actuator — 1Remote keyless entry receiver — 1Keyfob battery and function — 1Horn function — 1Warning chime function — 1Hazard function — 1Keyfob ID set up with consult — 1Keyfob ID set up without consult — 1Power door lock system symptoms — 1Squeak and rattle trouble diagnoses — 1Hood assembly — 1Hood hinge — 1Radiator core support upper — 1Radiator core support lower — 1Front fender — 1Fender cover — 1Door assembly — 1Door hinge — 1Door check link — 1Door assembly — 1Door hinge — 1Door check link — 1Trunk lid assembly — 1Trunk lid striker — 1Trunk lid hinge — 1Torsion bar — 1Trunk lid weather-strip — 1Hood lock — 1Hood lock control cable — 1Hood lock bell crank — 1Door lock — 1Inside handle — 1Outside handle — 1Door lock — 1Inside handle — 1Outside handle — 1Trunk lid lock — 1Trunk lid opener handle — 1Trunk lid opener cable — 1Fuel filler lid — 1Fuel filler opener cable — 1Fuel filler lid lock — 1Door switch — 1Remote keyless entry receiver — 1Keyfob battery — 1Security control system (SEC) — 1Precautions — 1Component parts Component parts Component parts — 1Intelligent key system/engine start function — 1Nissan anti-theft system — 1Vehicle security system — 1Diagnosis system (BCM) — 1Diagnosis and repair work flow — 1Additional service when replacing control unit — 1P1610 Lock mode — 1P1611 ID Discord, IMMU-ECM — 1P1612 Chain of ECM-IMMU — 1B2192 ID discord, IMMU-ECM — 1B2193 Chain of ECM-IMMU — 1B2195 Anti-scanning — 1B2196 Dongle unit — 1B2198 NATS antenna AMP — 1B2555 Stop lamp — 1B2556 Push-button ignition switch — 1B2557 Vehicle speed — 1B2601 Shift position — 1B2602 Shift position — 1B2603 Shift position — 1B2604 Shift position — 1B2605 Shift position — 1B2608 Starter relay — 1B260F Engine status — 1B26F3 Starter control relay — 1B26F4 Starter control relay — 1B26F7 BCM — 1B26FC Key registration — 1B210B Starter control relay — 1B210C Starter control relay — 1B210D Starter relay — 1B210E Starter relay — 1B210F Shift position/clutch interlock switch — 1B2110 Shift position/clutch interlock switch — 1Engine does not start when intelligent key is inside of vehicle — 1Security indicator lamp does not turn on or blink — 1NATS antenna AMP — 1Push-button ignition switch — 1Remote keyless entry receiver — 1Precautions — 1Nissan vehicle immobilizer system-NATS — 1Diagnosis system (IPDM E/R) — 1Diagnosis and repair workflow — 1Inspection and adjustment — 1U1000 CAN Comm — 1U1010 Control unit (CAN) — 1P1610 Lock mode — 1B2190, P1614 NATS antenna AMP — 1B2191, P1615 Difference of key — 1B2192, P1611 ID discord, IMMU-ECM — 1B2193, P1612 Chain of ECM-IMMU — 1B2195 Anti-scanning — 1B2196 Dongle unit — 1Power supply and ground circuit — 1Vehicle security indicator — 1Nissan vehicle immobilizer systemnats symptoms — 1NATS antenna AMP — 1Precautions — 1Squeak and rattle trouble diagnoses — 1Windshield glass — 1Rear window glass — 1Front door glass — 1Front regulator — 1Rear door glass — 1Rear regulator — 1Precautions — 1System — 1Diagnosis and repair work flow — 1Power supply and ground circuit — 1Front power window switch (passenger side) — 1Rear power window switch — 1Power window motor — 1Door switch — 1None of the power windows can be operated using any switch — 1Driver side power window does not operate — 1Front passenger side power window does not operate — 1Rear LH side power window does not operate — 1Rear RH side power window does not operate — 1Power window main switch — 1Front power window switch — 1Rear power window switch — 1Precautions — 1Squeak and rattle trouble diagnoses — 1Front bumper — 1Under cover — 1Rear bumper — 1Front grille — 1Cowl top — 1Fender protector — 1Roof side molding — 1Door outside molding — 1Trunk lid finisher — 1Door parting seal — 1Rear spoiler — 1Body repair (BRM) — 1Precautions — 1Precautions in repairing high strength steel — 1Repairing material — 1Corrosion protection — 1Replacement operations — 1Body alignment — 1Precautions — 1Door mirror remote control switch (mirror switch/changeover switch) — 1Squeak and rattle trouble diagnoses — 1Inside mirror — 1Door mirror assembly — 1Front door corner finisher — 1Door mirror glass — 1Door mirror rear finisher — 1Door mirror remote control switch — 1Precautions — 1Headlamp system — 1With daytime light system — 1Front fog lamp system — 1Turn signal and hazard warning lamp system — 1Parking, license plate and tail lamp system — 1Diagnosis system (IPDM E/R) (with intelligent key system) — 1Diagnosis system (IPDM E/R) (without intelligent key system) — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Headlamp (HI) circuit — 1Headlamp (LO) circuit — 1Parking lamp circuit — 1Turn signal lamp circuit — 1Front fog lamp circuit — 1Both side headlamps do not switch to high beam — 1Both side headlamps (LO) are not turned on — 1Parking, license plate and tail lamps are not turned on — 1Both side front fog lamps are not turned on — 1Headlamp aiming adjustment — 1Front fog lamp aiming adjustment — 1Front combination lamp — 1Front fog lamp — 1Combination switch — 1Hazard switch — 1Rear combination lamp — 1High-mounted stop lamp — 1License plate lamp — 1Precautions — 1System — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Battery saver output/power supply circuit — 1Interior room lamp control circuit — 1Trunk room lamp circuit — 1Push-button ignition switch illumination circuit — 1Map lamp — 1Interior room lamp — 1Console lamp — 1Trunk room lamp — 1Precautions — 1System — 1Diagnosis system (IPDM E/R) (With intelligent key system) — 1Diagnosis system (IPDM E/R) (Without intelligent key system) — 1Diagnosis and repair workflow — 1Wiper and washer fuse — 1Front wiper motor lo circuit — 1Front wiper motor hi circuit — 1Front wiper auto stop signal circuit — 1Front wiper motor ground circuit — 1Washer motor circuit — 1Washer switch — 1Front wiper does not operate — 1Normal operating condition — 1Wiper arm — 1Wiper blade — 1Wiper refill — 1Wiper drive assembly — 1Washer tank — 1Washer pump — 1Washer nozzle — 1Washer tube — 1Precautions — 1System — 1Diagnosis and repair work flow — 1Rear window defogger switch — 1Rear window defogger relay — 1Rear window defogger power supply and ground circuit — 1Driver side door mirror defogger — 1Passenger side door mirror defogger — 1Rear window defogger and door mirror defogger do not operate — 1Both doors mirror defogger don't operate but rear window defogger operates — 1Filament — 1Precautions — 1Horn — 1Precautions — 1Power socket — 1Body control system (BCS) — 1Precautions — 1System — 1Diagnosis system (BCM) — 1BCM — 1Inspection and adjustment — 1U1000 CAN Comm circuit — 1U1010 Control unit (CAN) — 1U0415 Vehicle speed — 1B2562 Low voltage — 1Power supply and ground circuit — 1Combination switch input circuit — 1Combination switch output circuit — 1BCM (Body control module) — 1Combination switch — 1Precautions — 1System — 1BCM — 1Inspection and adjustment — 1U1000 CAN Comm — 1U1010 Control unit (CAN) — 1Power supply and ground circuit — 1Combination switch input circuit — 1Combination switch output circuit — 1BCM (Body control module) — 1Combination switch — 1LAN System (LAN) — 1Precautions — 1System — 1Trouble diagnosis — 1Diagnosis and repair workflow — 1Precautions — 1CAN Communication system — 1Main line between IPDM-E and DLC circuit — 1ECM Branch line circuit — 1ABS Branch line circuit — 1IPDM-E Branch line circuit — 1TCM Branch line circuit — 1A-BAG Branch line circuit — 1AV Branch line circuit — 1DLC Branch line circuit — 1EPS Branch line circuit — 1M&A Branch line circuit — 1STRG Branch line circuit — 1BCM Branch line circuit — 1CAN Communication circuit — 1Main line between IPDM-E and DLC circuit — 1ECM Branch line circuit — 1ABS Branch line circuit — 1IPDM-E Branch line circuit — 1A-BAG Branch line circuit — 1DLC Branch line circuit — 1EPS Branch line circuit — 1M&A Branch line circuit — 1STRG Branch line circuit — 1BCM Branch line circuit — 1CAN Communication circuit — 1Main line between IPDM-E and DLC circuit — 1ECM Branch line circuit — 1ABS Branch line circuit — 1IPDM-E Branch line circuit — 1TCM Branch line circuit — 1A-BAG Branch line circuit — 1DLC Branch line circuit — 1EPS Branch line circuit — 1M&A Branch line circuit — 1STRG Branch line circuit — 1BCM Branch line circuit — 1CAN Communication circuit — 1Main line between IPDM-E and DLC circuit — 1ECM Branch line circuit — 1ABS Branch line circuit — 1IPDM-E Branch line circuit — 1TCM Branch line circuit — 1A-BAG Branch line circuit — 1DLC Branch line circuit — 1EPS Branch line circuit — 1M&A Branch line circuit — 1STRG Branch line circuit — 1BCM Branch line circuit — 1CAN Communication circuit — 1Main line between IPDM-E and DLC circuit — 1ECM Branch line circuit — 1ABS Branch line circuit — 1IPDM-E Branch line circuit — 1TCM Branch line circuit — 1A-BAG Branch line circuit — 1AV Branch line circuit — 1DLC Branch line circuit — 1EPS Branch line circuit — 1M&A Branch line circuit — 1STRG Branch line circuit — 1BCM Branch line circuit — 1CAN Communication circuit — 1Power control system (PCS) — 1Precautions — 1System — 1Diagnosis system (IPDM E/R) — 1IPDM E/R (Intelligent power distribution module engine room) — 1U1000 CAN Comm circuit — 1B2098 Ignition relay on stuck — 1B2099 Ignition relay off stuck — 1Power supply and ground circuit — 1IPDM E/R — 1Precautions — 1System — 1Diagnosis system (IPDM E/R) — 1IPDM E/R (Intelligent power distribution module engine room) — 1U1000 CAN Comm circuit — 1B2098 Ignition relay on stuck — 1B2099 Ignition relay off stuck — 1Power supply and ground circuit — 1IPDM E/R — 1Precautions — 1Power distribution system — 1Diagnosis and repair work flow — 1U1000 CAN Comm circuit — 1B2614 ACC Relay circuit — 1B2615 Blower relay circuit — 1B2616 Ignition relay circuit — 1B2618 BCM — 1B261A Push-button ignition switch — 1B26F1 Ignition relay — 1B26F2 Ignition relay — 1B26F6 BCM — 1Push-button ignition switch — 1Push-button ignition switch does not operate — 1Push-button ignition switch — 1Precautions — 1System — 1Diagnosis and repair workflow — 1Charging system preliminary inspection — 1Power generation voltage variable control system operation inspection — 1B Terminal circuit — 1L Terminal circuit (open) — 1L Terminal circuit (short) — 1S Terminal circuit — 1Generator — 1Precautions — 1Battery — 1Power supply routing circuit — 1Harness — 1Harness connector — 1Battery — 1Meter, warning lamp & indicator (MWI) — 1Precautions — 1System — 1Diagnosis system (combination meter) — 1Diagnosis and repair workflow — 1U1000 CAN Comm circuit — 1DTC B2205 Vehicle speed circuit — 1B2267 Engine speed — 1Power supply and ground circuit — 1Fuel level sensor signal circuit — 1Washer fluid level switch circuit — 1The fuel gauge indicator does not operate — 1The oil pressure warning lamp does not turn on — 1The low washer fluid warning continues displaying, or does not display — 1Combination meter — 1Combination meter — 1Precautions — 1System — 1Diagnosis system (combination meter) — 1Diagnosis and repair workflow — 1U1000 CAN Comm circuit — 1DTC B2205 Vehicle speed circuit — 1B2267 Engine speed — 1Power supply and ground circuit — 1Fuel level sensor signal circuit — 1Washer fluid level switch circuit — 1The fuel gauge indicator does not operate — 1The oil pressure warning lamp does not turn on — 1The low washer fluid warning continues displaying, or does not display — 1Combination meter — 1Combination meter — 1Warning chime system (WCS) — 1Precautions — 1System — 1Diagnosis system (combination meter) — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Meter buzzer circuit — 1Seat belt buckle switch signal circuit — 1Key switch signal circuit (without intelligent key) — 1Parking brake switch signal circuit — 1The parking brake release warning continues sounding, or does not sound — 1The seat belt reminder warning continues sounding, or does not sound — 1The light reminder warning does not sound — 1The key warning does not sound (without intelligent key) — 1Precautions — 1Audio system — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Front door speaker — 1Rear door speaker — 1Normal operating condition — 1Audio unit — 1Front door speaker — 1Rear door speaker — 1Roof antenna — 1Precautions — 1System — 1Diagnosis system (audio unit) — 1Diagnosis system (bluetooth control unit) — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Front door speaker — 1Rear door speaker — 1Bluetooth voice signal circuit — 1Bluetooth control signal circuit — 1Microphone signal circuit — 1Steering switch — 1Audio system — 1Normal operating condition — 1Audio unit — 1Front door speaker — 1Rear door speaker — 1Roof antenna — 1Steering audio control switch — 1Bluetooth antenna — 1Bluetooth control unit — 1Microphone — 1Precautions — 1System — 1Diagnosis system (audio unit) — 1Diagnosis system (bluetooth control unit) — 1Diagnosis and repair workflow — 1Power supply and ground circuit — 1Front door speaker — 1Rear door speaker — 1Bluetooth voice signal circuit — 1Bluetooth control signal circuit — 1Microphone signal circuit — 1Steering switch — 1USB Connector — 1Audio system — 1Normal operating condition — 1Audio unit — 1Front door speaker — 1Rear door speaker — 1USB Connector — 1Bluetooth control unit — 1Steering audio control switch — 1Bluetooth antenna — 1Microphone — 1Roof antenna — 1Precautions — 1System — 1Diagnosis system (AV Control unit) — 1Diagnosis and repair workflow — 1Inspection and adjustment — 1U1000 CAN Comm circuit — 1U1244 GPS Antenna — 1U1258 Satellite radio antenna — 1U1263 USB — 1U1264 Antenna AMP — 1U12AA Configuration error — 1U12B0 Power supply voltage — 1U12B1 Power supply voltage — 1Power supply and ground circuit — 1Front door speaker — 1Rear door speaker — 1Rear view camera image signal circuit — 1Microphone signal circuit — 1Steering switch — 1USB Connector — 1Auxiliary input jack — 1Multi AV system — 1Normal operating condition — 1AV Control unit — 1USB Connector — 1Front door speaker — 1Rear door speaker — 1Satellite radio antenna — 1Steering audio control switch — 1GPS Antenna — 1Cruise control & driver assistance — 1Precautions — 1General maintenance — 1Periodic maintenance — 1Recommended fluids and lubricants — 1Drive belt — 1Engine coolant — 1Fuel lines — 1Air cleaner filter — 1Engine oil — 1Oil filter — 1Spark plug — 1Exhaust system — 1CVT Fluid — 1A/T Fluid — 1Clutch fluid — 1M/T Oil — 1Road wheel — 1Brake fluid level and leaks — 1Brake lines and cables — 1Brake fluid — 1Disc brake — 1Drum brake — 1Steering gear and linkage — 1Axle and suspension parts — 1Seat belt, buckles, retractors, anchors and adjusters — 1
27steps
~162min
4/5difficulty
Done 0 of 27

Exploded View

CAMSHAFT

1. Camshaft bracket (No. 2 to 5) 2. Camshaft bracket (No. 1) 3. Camshaft sprocket (EXH) 4. Exhaust valve timing control solenoid valve 5. Oring 6. Camshaft sprocket (INT) 7. Plug (EXH) 8. Washer (EXH) 9. Oil filter (for exhaust valve timing control solenoid valve) 10. Cylinder head 11. Oil filter (for intake valve timing control solenoid valve) 12. Washer (INT) 13. Plug (INT) 14. Oring 15. Intake valve timing control solenoid valve 16. Bracket 17. Valve lifter 18. Camshaft (INT) 19. Camshaft (EXH)

Removal and Installation

CAUTION:

The rotation direction indicated in the procedure is as viewed from the engine front.

REMOVAL

  1. Hold the bottom surface of the engine with a jack to remove the right engine mount assembly and the insulator.
  2. Remove rocker cover.
  3. Place cylinder No. 1 at TDC of its compression stroke:

a. Rotate crankshaft pulley (2) clockwise and align TDC mark (without paint mark) (A) to timing indicator (1) on front cover.

(B) : White paint mark (Not used for service)

CAMSHAFT

b. Check that the matching marks on each of the camshaft sprockets are in the position as shown.

(1) : Timing chain

(2) : Camshaft sprocket (EXH)

(3) : Camshaft sprocket (INT)

(A) : Matching mark (Peripheral groove)

(B) : Pink link

(C) : Matching mark (Peripheral groove)

  • If not, rotate crankshaft pulley one more turn to align matching marks to the positions as shown.
CAMSHAFT

c. Paint matching marks (A) on the timing chain links.

  1. Remove crankshaft pulley.
  2. Remove front cover.
  3. Secure the plunger of chain tensioner in the fully compressed position. Then, loosen the timing chain tension.

a. Fully push down the lever (B) of chain tensioner (2) from the plug hole, and then insert the stopper pin (A) into the body side hole and secure the lever at the lowest position.

(C) : Front cover has been removed for clarity.

  • The tab is released by fully pushing the lever down. As a result, the plunger (1) can be moved.

NOTE:

Hexagonal wrench [2.5 mm (0.098 in)] is used for a stopper pin as an example.

CAUTION:

The stopper pin must use a shape that cannot fall in the front cover if dropped.

CAMSHAFT

b. Turn the crankshaft pulley (2) counterclockwise with the camshaft (EXH) (1) held. Apply the tension to the timing chain, and then push the plunger into the inside of chain tensioner.

CAUTION:

Hold the camshaft hexagonal part (A), and then secure the camshaft.

CAMSHAFT

c. Pull out the stopper pin (A) of chain tensioner (2) side from plug hole. Lift the lever (B) up to align its hole position with the hole of the body.

(D) : Front cover has been removed for clarity.

  • When the lever hole (C) is aligned with the body hole position, the plunger (1) is secured.
  • When the protrusion parts of the plunger ratchet and the tab face each other, both hole positions are not aligned. At that time, correctly engage them and align these hole positions by slightly moving the plunger.
CAMSHAFT

d. Insert the stopper pin into the body hole through the lever hole, and then secure the lever at the upper position.

  1. Remove timing chain.
  2. Remove camshaft sprocket (EXH) (1).

CAUTION:

  • Hold the camshaft hexagonal part (A), and then secure the camshaft.
  • Do not rotate crankshaft and camshaft separately, so as not to contact valve with piston.

NOTE:

The timing chain with the front cover installed is not disengaged from the crankshaft sprocket and it is not dropped into the front cover. Therefore, the timing chain tension holding device is not necessary.

9. Turn the camshaft sprocket (INT) to the most advanced position.

CAMSHAFT

CAUTION:

Installation and removal of the camshaft sprocket (INT) must be done in the most advanced position.

Make sure to follow the procedure exactly.

  • The sprocket (C) and vane (camshaft coupling) (B) are designed to spin and move within the range of a certain angle.
  • With the engine stopped and the vane in the most retarded angle, it will not spin because it is locked to the sprocket side by the internal lock pin (A).
  • If the camshaft sprocket bolts are turned in the situation described above, the lock pin will become damaged and cause malfunctions because of the increased horizontal load (cutting force) on the lock pin.
CAMSHAFT
  • Put the camshaft sprocket (INT) in the most advanced position:

a. Remove camshaft bracket (No. 1) (1).

: Engine front

  • Loosen the bolts in several steps, and then remove them.
CAMSHAFT

b. Apply the following air pressure to the No. 1 journal oil hole (A) of camshaft (INT) (1) shown using an air gun.

Air pressure : 300 kPa (3.1 kg/cm2, 44 psi) or more

  • Apply the air pressure into the oil hole on the second groove from the front of camshaft thrust (B).
  • Proceed all the way through step "e" with the air pressure on.
  • Attach the rubber nozzle narrowed to the top of the air gun to prevent air leakage from the oil hole (A). Securely apply the air pressure to the oil hole.

WARNING:

Eye protection should be worn as needed.

CAUTION:

  • There are other oil holes in the side grooves. Do not use the incorrect oil holes.
  • Be sure not to damage the oil path with the tip of the air gun.
  • Wipe all the oil off the air gun to prevent oil from being blown all over along with the air, and the area around the air gun should be wiped with a rag when applying air pressure. Eye protection should be worn as needed.

NOTE:

The air pressure is used to move the lock pin into the disengage position.

CAMSHAFT

c. Hold the camshaft sprocket (INT) with hands, and then apply the power counterclockwise/clockwise alternately.

(A) : Air gun

(B) : Rubber nozzle

  • Finally rotate the sprocket of the camshaft sprocket (INT) counterclockwise [the direction shown by the arrow ( )].
  • Perform the work while continuously applying the air pressure to the oil hole.
CAMSHAFT
  • If the lock pin is not released, tap the camshaft sprocket (INT) lightly with a plastic hammer (A).
  • If the camshaft sprocket (INT) is not rotated counterclockwise even if the above procedures are performed, check the air pressure and the oil hole position.
CAMSHAFT

d. While doing the above, once you hear a click (the sound of the internal lock pin disengaging) from inside the camshaft sprocket (INT), start turning the camshaft sprocket (INT) in the counterclockwise direction in the most advanced angle position.

(C) : Lock pin engaged

(D) : Most advanced angle

  • Keep the air pressure on.
  • If there is no click, as soon as the vane side (camshaft side) starts moving independently of the sprocket, the lock pin has become disengaged.
  • Check that it is in the most advanced angle position by seeing if the stopper pin groove (A) and the stopper pin hole (B) are matched up as shown.
CAMSHAFT

e. Stop applying air pressure and release the camshaft (INT).

f. Insert the stopper pin (A) into the stopper pin holes in the camshaft sprocket (INT) and lock in the most advanced angle position.

CAUTION:

No load is exerted on the stopper pin (spring reaction, etc.).

Since it comes out easily, secure it with tape (B) to prevent it from falling out.

NOTE:

The stopper pin shows one example of a hexagonal wrench for 2.5 mm (0.098 in) [length of inserted section: approximately15 mm (0.59 in)].

CAMSHAFT

10. Remove the camshaft sprocket (INT):

a. Keeping the camshaft hexagonal part (A) in place with the wrench, loosen the bolts for the camshaft sprocket (INT) (2).

(1) Camshaft (INT)

CAMSHAFT

CAUTION:

  • Do not drop stopper pin.
  • Tape (C) the stopper pin (B) so it does not come out.
  • Do not subject it to impact by dropping.
  • Do not disassemble. [Do not loosen the three bolts (A)].

NOTE:

While removing the camshaft sprocket (INT), if you have taken out the stopper pin and the lock pin has been rejoined in the most retarded angle, do the following to restore it.

i. Install the camshaft (INT) and tighten the bolts enough to prevent air from leaking out.

CAUTION:

The internal lock pin will get damaged, so keep the torque on the bolts to the minimum required to prevent air from escaping.

ii. Apply the air pressure, disengage the lock pin, and turn the vane to the most advanced angle position.

iii. Insert the stopper pin.

iv. Remove camshaft sprocket (INT) from the camshaft.

11. Remove camshaft brackets (No. 2 to 5).

CAMSHAFT
  • Loosen bolts in several steps in the reverse order as shown.

(A) : EXH side

(B) : INT side

: Engine front

NOTE:

The camshaft bracket (No. 1) has been already removed.

CAMSHAFT
  1. Remove camshaft (EXH).
  2. Remove camshaft (INT).
  3. Remove valve lifter.

- Identify installation positions, and store lifters without mixing them up.

  1. Remove intake valve timing control solenoid valve (1).
  2. Remove the alternator and bracket, remove the plug (2), and then remove the oil filter
    CAMSHAFT
  3. Remove exhaust valve timing control solenoid valve.
  4. Remove the plug on the exhaust valve timing control solenoid valve and the oil filter.
  5. For component inspection after removal

INSTALLATION

CAUTION:

Do not reuse Orings or washers.

1. Install oil filter (1) for intake and exhaust valve timing control solenoid valves.

CAUTION:

Do not reuse washers.

NOTE:

The intake side is shown as an example.

  • The oil filter (1) and washer (2) are assembled to the plug (3), and then install them in to the cylinder head.
CAMSHAFT

2. Install intake and exhaust valve timing control solenoid valves.

  • Insert it straight into the cylinder head.
  • Tighten bolts.

3. Install valve lifters.

  • If they are reused, install them in the original positions.

4. Put a matching mark for positioning the camshaft (INT) and the camshaft sprocket (INT):

NOTE:

This helps prevent the knock pin from engaging with the incorrect pin hole after installing the camshaft (INT) and the camshaft sprocket (INT).

a. Put the matching marks (A) on a line extending from the knock pin position of camshaft (INT) (1) front surface.

  • Put the marks on the visible position with the camshaft sprocket installed as shown.

b. Put the matching marks on a line extending from the knock pin hole (B) position of camshaft sprocket (INT) (2) as shown.

  • Put the marks on the visible position with it installed to the camshaft.
CAMSHAFT

5. Put a matching mark for positioning the camshaft (EXH) and the camshaft sprocket (EXH):

NOTE:

This helps prevent the knock pin from engaging with the incorrect pin hole after installing the camshaft (INT) and the camshaft sprocket (EXH).

a. Put the matching marks (A) on a line extending from the knock pin position of camshaft (EXH) (1) front surface.

  • Put the marks on the visible position with the camshaft sprocket installed as shown.

b. Put the matching marks on a line extending from the knock pin hole (B) position of camshaft sprocket (EXH) (2) as shown.

  • Put the marks on the visible position with it installed to the camshaft.
CAMSHAFT

6. Install camshaft

(1) : Camshaft (EXH)

(2) : Camshaft (INT)

(A) : Identification mark

  • Note that the camshafts (INT and EXH) have different shapes at the rear.
CAMSHAFT
  • Install camshafts to the cylinder head so that knock pins (A) on front end are positioned as shown.

(1) : Camshaft (EXH)

(2) : Camshaft (INT)

: Upper side

NOTE:

Though camshaft does not stop at the portion as shown for the placement of cam nose, it is generally accepted camshaft is placed for the same direction as shown.

CAMSHAFT

7. Install camshaft brackets (No. 2 to 5) aligning the identification marks on upper surface as shown.

(A) : EXH side

(B) : INT side

: Engine front

  • Install so that identification mark can be correctly read when viewed from the INT side.
CAMSHAFT

8. Tighten bolts of camshaft brackets in the following steps, in numerical order as shown.

(A) : EXH side

(B) : INT side

: Engine front

a. Tighten No. 9 to 11 in numerical order.

Camshaft bracket bolts : 1.96 N*m (2.0 kgm, 14 inlb)

b. Tighten No. 1 to 8 in numerical order.

Camshaft bracket bolts : 1.96 N*m (2.0 kgm, 14 inlb)

c. Tighten all bolts in numerical order.

Camshaft bracket bolts : 5.88 N*m (0.60 kgm, 52 inlb)

d. Tighten all bolts in numerical order.

Camshaft bracket bolts : 10.4 N*m (1.1 kgm, 8 ftlb)

CAMSHAFT

9. Install the camshaft sprocket (INT and EXH) to the camshaft (INT and EXH):

a. Refer to the matching mark (A) added in step 4. Securely align the knock pin and the pin hole, and then install them.

NOTE:

The intake side is shown as an example.

CAMSHAFT

10. Tighten the camshaft sprocket bolt (INT and EXH).

(1) : Camshaft sprocket (EXH)

CAUTION:

Hold the camshaft hexagonal part (A), using a suitable tool to secure the camshaft.

CAMSHAFT

11. Install the camshaft (INT and EXH) to the camshaft sprocket (INT and EXH) (2 and 3) while aligning the matching mark (marked when timing chain is removed) (A) and the pink link (B) of camshaft sprocket (INT and EXH).

(1) : Timing chain

(C) : Matching mark (peripheral groove)

  • If the positions of knock pin and pin groove are not aligned, move the camshaft (EXH) slightly to correct these positions.
CAMSHAFT

12. Pull out the stopper pin (A), and then apply the tension to the timing chain by rotating the crankshaft pulley clockwise slightly.

(1) : Plunger

(2) : Chain tensioner

(B) : Lever

(C) : Lever hole

(D) : Front cover has been removed for clarity.

CAMSHAFT
  1. Pull out the stopper pin of chain tensioner.
  2. Install front cover.
  3. Return the camshaft sprocket (INT) in the most retarded position:

a. Remove the stopper pin (A) from the camshaft sprocket (INT).

(B) : Tape

CAMSHAFT

b. Turn the crankshaft pulley (1) slowly clockwise (A) and return the camshaft sprocket (INT) to the most retarded angle position.

CAMSHAFT
  • When first turning the crankshaft, the camshaft sprocket (INT) will turn. Once it is turned more, and the vane (camshaft) also turns, then it has reached the most retarded angle position.

(B) : Stopper pin hole

(C) : Most advanced angle

(D) : Lock pin engaged

  • The most retarded angle position can be checked by seeing if the stopper pin groove (A) is shifted clockwise.
  • After spinning the crankshaft slightly in the counterclockwise direction, you can check the lock pin has joined by seeing if the vane (camshaft) and the sprocket move together.
CAMSHAFT

16. Install the camshaft position sensor (PHASE) to the rear end of cylinder head.

  • Tighten bolts with it completely inserted.

17. Check and adjust valve clearance.

18. Installation of the remaining components is in the reverse order of removal.

INSPECTION AFTER INSTALLATION

  • Before starting engine, check oil/fluid levels, including engine coolant and engine oil. If less than required quantity, fill to the specified level.
  • Use procedure below to check for fuel leakage.
  • Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points.
  • Start engine. With engine speed increased, check again for fuel leakage at connection points.
  • Run engine to check for unusual noise and vibration.

NOTE:

If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop after hydraulic pressure rises.

  • Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including engine oil and engine coolant.
  • Bleed air from passages in lines and hoses, such as in cooling system.
  • After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to specified level, if necessary.
  • Summary of the inspection items:
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Transmission/ transaxle fluid A/T and CVT Models Leakage Level/Leakage Leakage
M/T Models Level/Leakage Leakage Level/Leakage
Other oils and fluids* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gas Leakage

*Power steering fluid, brake fluid, etc.

Inspection

INSPECTION AFTER REMOVAL

Oil Filter

  • Check that there is no foreign material on the oil filter (1) and check it for clogging.
  • Check the oil filter for damage.
  • If there is some damage, replace the oil filter, the plug, and the washer as a set.

CAUTION:

Do not reuse the washer.

Oil Filter

Camshaft Runout

1. Put Vblock on a precise flat table, and support No. 2 and 5 journals of camshaft.

CAUTION:

Do not support No. 1 journal (on the side of camshaft sprocket) because it has a different diameter from the other four locations.

  1. Set a dial indicator vertically to No. 3 journal.
  2. Turn camshaft to one direction, and measure the camshaft runout on the dial indicator. (Total indicator reading)
    Camshaft Runout

4. If it exceeds the limit, replace camshaft.

Camshaft Cam Height

1. Measure the camshaft cam height with a micrometer (A).

2. If wear exceeds the limit, replace camshaft.

Camshaft Cam Height

Camshaft Journal Oil Clearance

CAMSHAFT JOURNAL DIAMETER

Measure the outer diameter of camshaft journal with a micrometer (A).

Camshaft Journal Oil Clearance

CAMSHAFT BRACKET INNER DIAMETER

  • Tighten camshaft bracket bolts to the specified torque. Refer to "INSTALLATION" for the tightening procedure.
  • Measure inner diameter (b) of camshaft bracket with a bore gauge (A).
CAMSHAFT BRACKET INNER DIAMETER

CAMSHAFT JOURNAL OIL CLEARANCE

  • (Oil clearance) = (Camshaft bracket inner diameter) - (Camshaft journal diameter)
  • If it exceeds the limit, replace either or both camshaft and cylinder head.

NOTE:

Camshaft brackets cannot be replaced as single parts, because they are machined together with cylinder head. Replace whole cylinder head assembly.

Camshaft End Play

  1. Install camshaft in cylinder head.
  2. Install a dial indicator (A) in thrust direction on front end of camshaft.

    Measure the camshaft end play on the dial indicator when camshaft is moved forward/backward (in direction to axis).

    Camshaft End Play
  • Measure the following parts if out of the standard.
    • Dimension "A" for cylinder head No. 1 journal bearing

Standard : 4.000 4.030 mm (0.1574 0.1586 in)

  • Dimension "B" for camshaft thrust

Standard : 3.877 3.925 mm (0.1526 0.1545 in)

  • Refer to the standards above, and then replace camshaft and/ or cylinder head.
Camshaft End Play

Camshaft Sprocket Runout

1. Put Vblock on precise flat table, and support No. 2 and 5 journals of camshaft.

CAUTION:

Do not support No. 1 journal (on the side of camshaft sprocket) because it has a different diameter from the other four locations.

2. Measure the camshaft sprocket runout with a dial indicator (A).

(Total indicator reading)

Limit : 0.15 mm (0.0059 in)

  • If it exceeds the limit, replace camshaft sprocket.
Camshaft Sprocket Runout

Valve Lifter

Check if surface of valve lifter has any wear or cracks.

  • If anything above is found, replace valve lifter.
Valve Lifter

Valve Lifter Clearance

VALVE LIFTER OUTER DIAMETER

  • Measure the outer diameter of valve lifter with a micrometer (A).
Valve Lifter Clearance

VALVE LIFTER HOLE DIAMETER

Measure the diameter of valve lifter hole of cylinder head with an inside micrometer (A).

VALVE LIFTER HOLE DIAMETER

VALVE LIFTER CLEARANCE

  • (Valve lifter clearance) = (Valve lifter hole diameter) - (Valve lifter outer diameter)
  • If out of the standard, referring to the each standard of valve lifter outer diameter and valve lifter hole diameter, replace either or both valve lifter and cylinder head.

INSPECTION AFTER INSTALLATION

Inspection of Camshaft Sprocket Oil Groove

CAUTION:

  • Perform this inspection only when DTC P0011 or P0014 is detected in selfdiagnostic results of CONSULT and it is directed according to inspection procedure of EC section.
  • Check when engine is cold so as to prevent burns from the splashing engine oil.

NOTE:

This section provides the inspection method of oil passage of cam sprocket on the intake side. For oil passage on the exhaust side, the inspection procedure must be changed as instructed below:

Step 3 : Remove exhaust valve timing control solenoid valve. Refer to EM56, "Exploded View".

Step 4 : Crank engine, and then check that engine oil comes out from exhaust valve timing control solenoid valve hole (A). End crank after checking.

Step 5 Perform the following inspection if engine oil does not come out from exhaust valve timing control solenoid valve oil hole of the cylinder head.

  • Remove oil filter, and then clean it. Refer to EM56, "Exploded View".
  • Clean oil groove between oil strainer and exhaust valve timing control solenoid valve. Refer to EM56, "Exploded View".

Step 6 : Remove components between exhaust valve timing control solenoid valve and camshaft sprocket (EXH), and then check each oil groove for clogging.

  1. Check engine oil level.
  2. Perform the following procedure so as to prevent the engine from being unintentionally started while checking.

a. Release the fuel pressure.

b. Remove intake manifold.

c. Disconnect ignition coil and injector harness connectors.

  1. Remove intake valve timing control solenoid valve.
  2. Crank engine, and then check that engine oil comes out from intake valve timing control solenoid valve hole (A). End crank after checking.

(1) : Plug

:Engine front

WARNING:

  • Be careful not to touch rotating parts (drive belts, idler pulley, and crankshaft pulley, etc.).

CAUTION:

  • Prevent splashing by using a shop cloth to prevent injury from splashing engine oil and so as to prevent engine oil contamination.
  • Use a shop cloth to prevent engine oil from being splashed to engine and vehicle. Especially be careful not to spill engine oil to rubber parts of drive belts, engine mounting insulator, etc. Wipe engine oil off immediately if it is splashed.
Inspection of Camshaft Sprocket Oil Groove

5. Perform the following inspection if engine oil does not come out from intake valve timing control solenoid valve oil hole of the cylinder head.

  • Remove oil filter, and then clean it.
  • Clean oil groove between oil strainer and intake valve timing control solenoid valve.

6. Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT), and then check each oil groove for clogging.

  • Clean oil groove if necessary.

7. After inspection, installation of components is in the reverse order of removal