Cylinder Head Cover Removal and Installation
Removal
Front
1. Connector (Front Secondary HO2S) - Disconnect
2. Intake Manifold - Remove
3. Front Cylinder Ignition Coil - Remove
4. Connector and Positive Cable (Alternator) - Disconnect
5. Front Cylinder Head Cover Harness Holder - Move

- Disconnect the connectors (A).
- Remove the harness clips (B) and the connector clamp (C).
- Move the front cylinder head cover harness holder (D).
6. Front Cylinder Head Cover - Remove

- Remove the front cylinder head cover.
- Remove the heat insulator (A) as needed.
Rear
1. Intake Manifold - Remove
2. Rear Cylinder Ignition Coil - Remove
3. Connector (Rocker Arm Oil Pressure Sensor) - Disconnect
NOTE: Remove the rocker arm oil pressure sensor harness clips from the timing belt rear upper cover at the same time.
4. Harness Holder - Move

- Disconnect the connectors (A) and the ground cable (B).
- Remove the harness clips (C) and the harness holder clamps (D).
- Move the harness holder (E).
5. Rear Cylinder Head Cover Harness Holder - Move

- Remove the harness clip (A).
- Disconnect the breather hose (B).
- Disconnect the connectors (C).
- Move the rear cylinder head cover harness holder (D).
6. Rear Cylinder Head Cover - Remove

- Remove the rear cylinder head cover.
- Remove the heat insulator (A) as needed.
Installation
Front
1. Head Cover Gasket - Install

- Check the spark plug seals (A) for damage. If any seals are damaged, replace it.
- Thoroughly clean the head cover gasket (B) and the groove of the cylinder head cover (C).
NOTE: Check and if necessary, replace the head cover gasket.
- Install the head cover gasket in the groove of the cylinder head cover. Make sure the head cover gasket is seated securely.
2. Front Cylinder Head Cover - Install

- Apply liquid gasket to the front rocker arm oil control valve mating surfaces.
- Set the spark plug seals (A) on the spark plug tubes, and install the front cylinder head cover, then loosely install the front cylinder head cover mounting bolts.
- Inspect the spark plug seals for damage.
- If the heat insulator (B) removed, install the heat insulator.

- Tighten the bolts in three steps; tighten the bolts until the bolts sit on the front cylinder head cover, tighten the bolts until the gasket is compressed, tighten the bolts to specified torque.
3. Front Cylinder Head Cover Harness Holder - Install

- Install the front cylinder head cover harness holder (A).
- Connect the connectors (B).
- Install the harness clips (C) and the connector clamp (D).
- Tighten the front cylinder head cover harness holder mounting bolts (E).
4. Connector and Positive Cable (Alternator) - Connect
5. Front Cylinder Ignition Coil - Install
6. Intake Manifold - Install
7. Connector (Front Secondary HO2S) - Connect
Rear
1. Head Cover Gasket - Install

- Check the spark plug seals (A) for damage. If any seals are damaged, replace it.
- Thoroughly clean the head cover gasket (B) and the groove of the cylinder head cover (C).
NOTE: Check and if necessary, replace the head cover gasket.
- Install the head cover gasket in the groove of the cylinder head cover. Make sure the head cover gasket is seated securely.
2. Rear Cylinder Head Cover - Install

- Apply liquid gasket to the rear rocker arm oil control valve mating surfaces.
- Set the spark plug seals (A) on the spark plug tubes, and install the rear cylinder head cover, then loosely install the rear cylinder head cover mounting bolts.
- Inspect the spark plug seals for damage.
- If the heat insulator (B) removed, install the heat insulator.

- Tighten the bolts in three steps; tighten the bolts until the bolts sit on the rear cylinder head cover, tighten the bolts until the gasket is compressed, tighten the bolts to specified torque.
3. Rear Cylinder Head Cover Harness Holder - Install

- Install the rear cylinder head cover harness holder (A).
- Connect the connectors (B).
- Tighten the rear cylinder head cover harness holder mounting bolts (C).
- Connect the breather hose (D).
- Install the harness clip (E).
4. Harness Holder - Install

- Install the harness holder (A) and the harness clips (B).
- Connect the connectors (C) and the ground cable (D).
5. Connector (Rocker Arm Oil Pressure Sensor) - Connect
NOTE: Install the rocker arm oil pressure sensor harness clips to the timing belt rear upper cover at the same time.
6. Rear Cylinder Ignition Coil - Install
7. Intake Manifold - Install